2019 MAZDA MODEL CX-5 window

9. Align the blade component projectionwith the wiper arm notch.

Notch
Projection
10. Slide the blade component and install it to the wiper arm.

11. Slowly lower the wiper arm onto the
windshield.
▼Replacing Rear Window Wiper
Blade
When the wiper no longer cleans well, the
blade is probably worn or cracked.
Replace it.
CAUTION
To prevent damage to the wiper arm and
other components, do not move the wiper
by hand.
1. Remove the cover and raise the wiper
arm.
2. Firmly rotate the wiper blade to theright until it unlocks, then remove the
blade.
CAUTION
To prevent damage to the rear window,
do not let the wiper arm fall on it.
Maintenance and Care
Owner Maintenance
6-34
CX-5_8HE3-EA-18I_Edition1 2018-6-29 13:44:47

▼Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 CABIN.+B 50 A For protection of various circuits
2 IG2 30 A For protection of various circuits
3 INJECTOR
ENG.SUB 30 A Engine control system
4 SCR1
EVVT 20 A Engine control system
5P.WINDOW1 30 A ―
6 R.HEATER 20 A ―
7 ADD FAN DE 40 A ―
8 WIPER.DEI 20 A Windshield wiper de-icer
*
9DEFOG 40 A Rear window defogger
10 DCDC DE 40 A ―
11 EPB R 20 A Electric parking brake (EPB) (RH)
12 EPB L 20 A Electric parking brake (EPB) (LH)
Maintenance and Care
Owner Maintenance
6-54*Some models.
CX-5_8HE3-EA-18I_Edition1 2018-6-29 13:44:47

DESCRIPTIONFUSE
RATING PROTECTED COMPONENT
13 AUDIO
DCDC REG 30 A Audio system
14 FAN GE 30 A
Cooling fan
*
15 ENG.MAIN 40 A Engine control system
16 ABS/DSC M 50 A ABS, Dynamic stability control system
17 FAN DE 40 A ―
18 WIPER 20 A Front window wiper and washer
19 HEATER 40 A Air conditioner
20 ADD FAN GE 30 A Cooling fan
*
21 ENGINE.IG1 7.5 A Engine control system
22 C/U IG115 A For protection of various circuits
23 AUDIO2 7.5 A Audio system
24 METER2 7.5 A ―
25 ENGINE3 15 A Engine control system
26 ENGINE2 15 A Engine control system
27 ENGINE1 15 A Engine control system
*
28AT 15 A
Transaxle control system*, Ignition switch
29 H/CLEAN 20 A ―
30 A/C 7.5 A Air conditioner
31 AT PUMP 15 A ―
32 HORN 15 A Horn
33 R.WIPER 15 A Rear window wiper
34 H/L HI 20 A Headlight high beam
35 ST.HEATER 15 A Heated steering wheel
*
36FOG 15 A
Fog lights*
37 ENG.+B 7.5 A Engine control system
38 H/L LOW L 15 A Headlight low beam (LH)
39 ENGINE4 15 A Engine control system
*
40― ― ―
41 METER1 10 A Instrument cluster
42 SRS1 7.5 A Air bag
43 BOSE 25 A
Bose
® Sound System-equipped model*
44 AUDIO1 15 A Audio system
45 ABS/DSC S 30 A ABS, Dynamic stability control system
46 FUEL PUMP 15 A Fuel system
Maintenance and Care
Owner Maintenance
*Some models.6-55
CX-5_8HE3-EA-18I_Edition1 2018-6-29 13:44:47

DESCRIPTIONFUSE
RATING PROTECTED COMPONENT
47 FUEL WARM 25 A ―
48 TAIL 15 A Taillights, License plate lights, Parking lights
49 SCR2
FUEL PUMP2 25 A ―
50 HAZARD 25 A Hazard warning flashe rs, Turn signal lights, Parking lights
51 H/L LOW R 15 A Headlight low beam (RH)
52 OUTLET 25 A Accessory sockets
53 STOP 10 A Brake lights
54 ROOM 15 A For protection of various circuit
Fuse block (Left side)
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 P.SEAT D 30 A Power seat
*
2 P.WINDOW3 30 A Power windows
3 R.OUTLET3 15 A Accessory sockets
4 P.WINDOW2 25 A Power windows
5ESC L 1 5 A ―
Maintenance and Care
Owner Maintenance
6-56*Some models.
CX-5_8HE3-EA-18I_Edition1 2018-6-29 13:44:47

WA R N I N G
Dry off brakes that have become wet by
driving slowly, releasing the accelerator
pedal and lightly applying the brakes
several times until the brake performance
returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the vehicle
pulling to one side when braking could
result in a serious accident. Light braking
will indicate whether the brakes have been
affected.
When using an automatic car wash
Retract the door mirrors.
The automatic car wash brushes could
reduce the paint lustre or hasten paint
deterioration.
When using a high water pressure car
wash
High water temperature and high water
pressure car washers are available
depending on the type of car wash
machine. If the car washer nozzle is put
too close to the vehicle, the force of the
spray could damage or deform the
molding, affect the seal ability of parts, and
allow water to penetrate the interior. Keep
a sufficient space (30 cm (12 in) or more)
between the nozzle and the vehicle. In
addition, do not spend too much time
spraying the same area of the vehicle, and
be very careful wh en spraying between
gaps in doors and around windows.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.

1. Use wax which contains no abrasives. Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for
metallic, mica, and solid colors.
3. When waxing, coat evenly with the sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take off
the wax. Rewax these areas even if the rest
of the vehicle does not need it.
▼ Repairing Damage
to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.
CAUTION
If your Mazda is damaged and needs metal
parts repaired or replaced, make sure the
body shop applies anti-corrosion materials
to all parts, both repaired and new. This
will prevent them from rusting.
Maintenance and Care
Appearance Care
6-61
CX-5_8HE3-EA-18I_Edition1 2018-6-29 13:44:47

▼Instrument Panel Top (Soft pad)
Maintenance
Extremely soft material
is used for the soft
pad surface. If the soft pad surface is
rubbed harshly with a dry cloth, it could
result in the surface being damaged and
leaving white scratch marks.
1. Wipe the soiled area with a soft cloth
soaked in a mild detergent (approx.
5%) diluted with water.
2. Wipe off the remaining detergent using
a cloth soaked in clean water and
wrung out well.
▼Panel Maintenance
If a panel becomes soiled, wipe it off with
a soft cloth soaked in clean water and
thoroughly wrung out.
If some areas require further cleaning, use
the following procedure:
1. Wipe the soiled area with a soft cloth
soaked in a mild detergent (approx.
5 %) diluted with water.
2. Wipe off the remaining detergent using a cloth soaked in clean water and
wrung out well.
NOTE
Be particularly careful when cleaning
shiny surface panels and metallic parts
such as plating as they can be scratched
easily.
▼Active Driving Display
Maintenance*
The dust-proof sheet has a coating. When
cleaning, do not use a hard or
rough-surface cloth, o
r cleaning detergent.
In addition, if a chemical solvent gets on
the active driving d isplay, wipe it off
immediately. The dust-proof sheet could
be damaged and the surface coating could
be scratched. Use a fine, soft cloth such as
those used for cleaning eyeglasses.
NOTE
Use of compressed air when cleaning the
dust-proof sheet is recommended.
▼ Cleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy film, clean them with
glass cleaner. Follow
the directions on the
container.
CAUTION
 Do not scrape or scratch the inside of the
window glass. It could damage the
thermal filaments and the antenna lines.
 When washing the inside of the window
glass, use a soft cloth dampened in
lukewarm water, gently wiping the
thermal filaments and the antenna lines.
Use of glass cleaning products could
damage the thermal filaments and the
antenna lines.
▼ Cleaning the Floor Mats
Rubber floor mats should be cleaned with
mild soap and water only.
Maintenance and Care
Appearance Care
6-66*Some models.
CX-5_8HE3-EA-18I_Edition1
2018-6-29 13:44:47

ItemFeatureFactory
Setting Available Settings Settings
Change
Method
High Beam Control
System (HBC) (page
4-120) Operational/non-operational*1On On/Off A ―
Adaptive Front Lighting
System (AFS) (page
4-119)Operational/non-operational*1On On/Off A ―
Lights-on reminder*8
(page 7-42)
Warning beep volume High High/Low/Off A ―
Coming home light
(page 4-74)
Time until head
lights turn off 30 sec‐
onds 120 seconds/
90 seconds/
60 seconds/
30 seconds/ Off A―
Leaving home light
(page 4-75)
Operational/non-operational On On/Off A ―
Turn signal indicator
(page 4-77)
Beep volume High High/Low A ―
Three-flash turn signal
(page 4-77)Operational/non-operational On On/Off A ―
Ambient lights (page
5-95)
Ambient lights brightness*9MediumBright/
Medium/ Dim/
Off
*10
A―
Rear window defogger
(page 4-82) The operation time fo
r the rear window
defogger can be changed. 15 mi‐
nutes 15 minutes/Continu‐
ous*11――
System
Language Language indicated in display US Eng‐
lish Depends on mar‐
ket
*12A―
Temperature Temperature unit indicated in display °F °F/°C A ―
DistanceDistance unit indicated in display mi or km mi/km A ―
Fuel Economy Monitor (page 4-108)
Ending display Display/non-display Off On/Off B ―
Fuel economy resetting
procedure*Linkage/non-linkage with fuel economy
reset and trip meter A resetOff On/Off B ―
Specifications
Personalization Features
9-16*Some models.
CX-5_8HE3-EA-18I_Edition1
2018-6-29 13:44:47

ItemFeatureFactory
Setting Available Settings Settings
Change
Method
Active Driving Display (page 4-56)
Display Setting can be changed so that the Active
Driving Display is not displayed.
On On/Off C ―
The display height (up/down position)
can be changed.
013 steps up/down
from initial setting (total: 27 steps) C―
The method for adju
sting the display
brightness (automatically/manually) can
be changed. Auto Auto/Man. C ―
The standard brightness while automatic
adjustment is selected can be changed us‐
ing the brightness adjustment.
02 steps up/down from
initial setting (total: 5 steps) C―
The standard brightness while manual
adjustment is selected can be changed us‐
ing the brightness adjustment. 020 steps up/down
from initial setting (total: 41 steps) C―
The display angle can be changed.
03steps up/down from
initial setting (total: 7steps) C―
Navigation guidance Display/non-display
On On/Off C ―
*1 Though these systems can be turned Off, doing so will defeat the purpose of the system and Mazda
recommends that these systems remain On.
*2 Only the volume of the warning beep during Blind Spot Monitoring (BSM) operation ca n be changed. The
volume of the warning beep during Rear Cross Traffic Alert (RCT A) operation cannot be changed.
*3 This system functions only when the navigation system is funct ioning.*4 When the ultrasonic sensors detect an obstruction, the contents indicated on the center display switches to the
360°View Monitor. (Vehicles with 360°View Monitor)
*5 If the auto-wiper control is s et to Off, the wiper lever position is set to intermittent operation.*6 If the setting is changed to Of f, the following operation is performed according to the headlight switch
position:
At position: Headlights turn off i mmediately after the ignition i s switched off.At any position other than : Headlights on/off conditions vary according to the headlight switch
position. Refer to Headlights on page 4-71.
*7 When set to Off, the light s-on reminder is operable.*8 The lights-on reminder settings c an be changed at anytime, however, the lights-on reminder only operates
when the auto headlight function is set to Off. Refer to Lights-On Reminder on page 7-42.
*9 Change the ambient light illumi nation level with the parking lights or headlights turned on.*10 When set to OFF, the ambient lights remain turned off regardless of whether or not the parking lights or
headlights are on or off. Howev er, they will turn on or off in conjunction with the illuminated entry system.
*11 The operation may stop in 15 mi nutes due to the effect of the outside temperature even if the operation time of
the rear window defogger has been changed to Continuous.
*12 Available only in display from the center display.
Specifications
Personalization Features
9-17
CX-5_8HE3-EA-18I_Edition1 2018-6-29 13:44:47