2019 MAZDA MODEL CX-30 engine oil

▼Plastic Part Maintenance
xWhen cleaning the plastic lenses of
the lights, do not use petrol, paraffin,
rectified spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these
chemical agents can discolour or
damage the surfaces resulting in a
significant loss in functionality. If
plastic parts become inadvertently
exposed to any of these chemical
agents, flush with water immediately.
xIf plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fluids such as
petrol, oil, engine coolant, or battery
fluid, it could cause discolouration,
staining, or paint peeling. Wipe off
any such chemical agents or fluids
using a soft cloth immediately.
xHigh water temperature and high
water pressure car washers are
available depending on the type of
high pressure car washer device. If
the car washer nozzle is put too
close to the vehicle or aimed at one
area for an extended period of time,
it could deform plastic parts or
damage the paint.
xDo not use wax containing
compounds (polish). Otherwise, it
could result in paint damage.
xIn addition, do not use an electrical
or air tool to apply wax. Otherwise,
the frictional heat generated could
result in deformation of plastic parts
or paint damage.
Interior Care
▼Interior Care
WARNING
Do not spray water into the vehicle
cabin:
Spraying water into the vehicle cabin is
dangerous as electrical devices such as
the audio and switches could get wet
resulting in a malfunction or vehicle
fire.
NOTE
xDo not wipe the interior using
alcohol, chlorine bleach, or organic
solvents such as thinner, benzene,
and petrol. Otherwise, it may cause
discolouration or stains.
xRubbing hard with a stiff brush or
cloth may cause damage.
If the vehicle interior becomes soiled
by any of the following , wipe it off
immediately using a soft cloth.
Leaving it uncleaned could cause
discolouration, stains, cracks, or
peeling of the coating , and it will make
it hard to wipe off later.
xBeverage or fragrancexGrease or oilxSoiling
▼Seat Belt Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked
in a mild detergent (approx. 5%)
diluted with water.
2. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
3. Before retracting seat belts which
have been pulled out for cleaning,
dry them off thoroughly and make
Maintenance and Care
Appearance Care
6-59

WARNING
Do not jack up the vehicle higher
than is necessary:
Jacking up the vehicle higher than is
necessary is dangerous as it could
destabilize the vehicle resulting in
an accident.
Do not start the engine or shake
the vehicle while it is jacked up:
Starting the engine or shaking the
vehicle while it is jacked up is
dangerous as it could cause the
vehicle to fall off the jack resulting
in an accident.
Never go under the vehicle while it
is jacked up:
Going under the vehicle while it is
jacked up is dangerous as it could
result in death or serious injury if
the vehicle were to fall off the jack.
9. Remove the wheel nuts by turning
them anticlockwise; then remove
the wheel and centre cap.
▼Mounting the Spare Tyre
1. Remove dirt and grime from the
mounting surfaces of the wheel and
hub, including the hub bolts, with a
cloth.

WARNING
Make sure the mounting surfaces
of the wheel, hub and wheel nuts
are clean before changing or
replacing tyres:
When changing or replacing a tyre,
not removing dirt and grime from
the mounting surfaces of the wheel,
hub and hub bolts is dangerous.
The wheel nuts could loosen while
driving and cause the tyre to come
off, resulting in an accident.
2. Mount the spare tyre.
3. Install the wheel nuts with the
bevelled edge inward; tighten them
by hand.

WARNING
Do not apply oil or grease to
wheel nuts and bolts and do not
tighten the wheel nuts beyond the
recommended tightening torque:
Applying oil or grease to wheel nuts
and bolts is dangerous. The wheel
nuts could loosen while driving and
cause the tyre to come off, resulting
in an accident. In addition, wheel
nuts and bolts could be damaged if
tightened more than necessary.
4. Turn the jack handle anticlockwise
using the wheel brace and lower
the vehicle.
If Trouble Arises
Flat Tyre
7-37

When starting the engine, the brake
system warning light may turn on and
the warning indication may be
displayed. In this case, park the
vehicle in a safe location and release
the brake pedal.
If the brake system warning light/
warning indication does not turn off
even after parking the vehicle, have
the vehicle inspected by an expert
repairer (we recommend an
Authorised Mazda Repairer).

▼Electronic Brake Force Distribution
System Warning
If the electronic brake force
distribution control unit determines
that some components are operating
incorrectly, the control unit may
illuminate the brake system warning
light and the ABS warning light
simultaneously. The problem is likely to
be the electronic brake force
distribution system.
WARNING
Do not drive with both the brake
system warning light and ABS warning
light illuminated. Have the vehicle
towed to an expert repairer (we
recommend an Authorised Mazda
Repairer) to have the brakes inspected
as soon as possible:
Driving when the brake system warning
light and ABS warning light are
illuminated simultaneously is
dangerous.
When both lights are illuminated, the
rear wheels could lock more quickly in
an emergency stop than under normal
circumstances.
▼Charging System Warning
Indication/Warning Light
If the warning light illuminates while
driving , it indicates a malfunction of
the alternator or of the charging
system.
Drive to the side of the road and park
off the right-of-way. Consult an expert
repairer (we recommend an
Authorised Mazda Repairer).
CAUTION
Do not continue driving when the
charging system warning light is
illuminated because the engine could
stop unexpectedly.
▼Engine Oil Warning Indication/
Warning Light
This warning light indicates low engine
oil pressure.
CAUTION
Do not run the engine if the oil
pressure is low. Otherwise, it could
result in extensive engine damage.
If the light illuminates or the warning
indication is displayed while driving:
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-50

1. Drive to the side of the road and
park off the right-of-way on level
ground.
2. Turn off the engine and wait 5
minutes for the oil to drain back
into the sump.
3. Inspect the engine oil level (page
6-27). If it's low, add the
appropriate amount of engine oil
while being careful not to overfill.
CAUTION
Do not run the engine if the oil
level is low. Otherwise, it could
result in extensive engine damage.
4. Start the engine and check the
warning light.

If the light remains illuminated even
though the oil level is normal or after
adding oil, stop the engine
immediately and have your vehicle
towed to an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼High Engine Coolant Temperature
Warning Indication
Displays if the engine coolant
temperature has increased excessively.
“Elevated Engine Coolant Temp. Drive
Slowly” displayed
Drive slowly to reduce engine load
until you can find a safe place to stop
the vehicle and wait for the engine to
cool down.
“Excessive Engine Coolant Temp. Stop
the Vehicle in a Safe Location”
displayed
This indicates the possibility of
overheating. Park the vehicle in a safe
place immediately and stop the
engine.
Refer to Overheating on page 7-44.
CAUTION
Do not drive the vehicle with the high
engine coolant temperature warning
light illuminated. Otherwise, it could
result in damage to the engine.
▼Power Steering Malfunction
Indication/Indicator Light
The message is displayed if the electric
power steering has a malfunction.
If the message is displayed, stop the
vehicle in a safe place and do not
operate the steering wheel. There is no
problem if the indication turns off
when the engine is restarted after
some time has passed. If the indication
displays even after the engine is
restarted, contact an expert repairer
(we recommend an Authorised Mazda
Repairer) if the message is displayed
continuously.
NOTE
xIf the message is displayed, the
power steering will not operate
normally. In this case, the steering
wheel can still be operated,
however, the operation may feel
heavy compared to normal, or the
steering wheel could vibrate when
turning.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-51

NOTE
The light illumination timing may vary
because fuel inside the fuel tank moves
around according to the driving
conditions and the vehicle posture.
Action to be taken
Add fuel. If the light is flashing, refuel
as soon as possible.
▼Engine Oil Level Warning
Indication/Warning Light
This warning light indicates that the
engine oil level is around the MIN
mark (page 6-27).
CAUTION
Do not continue to drive the vehicle
with the engine oil level warning
indication/warning light displayed/
turned on. If the vehicle continues to
be driven with an insufficient amount
of engine oil, it could cause damage to
the engine.
Action to be taken
Add 1 L (0.3 US gal, 0.2 Imp gal) of
engine oil (page 6-24).
▼Seat Belt Warning Indication/
Warning Light (Front seat)
The seat belt warning light turns on if
the driver or front passenger's seat is
occupied and the seat belt is not
fastened with the ignition switched
ON.
If the driver or front passenger's seat
belt is unfastened (only when the front
passenger's seat is occupied) and the
vehicle is driven at a speed faster than
about 20 km/h (12 mph), the warning
light flashes. After a short time, the
warning light stops flashing, but
remains illuminated. If a seat belt
remains unfastened, the warning light
flashes again for a given period of
time.
NOTE
xIf the driver or front passenger's seat
belt is unfastened after the warning
light turns on, and the vehicle speed
exceeds 20 km/h (12 mph), the
warning light flashes again.
xPlacing heavy items on the front
passenger's seat may cause the front
passenger's seat belt warning
function to operate depending on
the weight of the item.
xTo allow the front passenger seat
weight sensor to function properly,
do not place and sit on an additional
seat cushion on the front passenger's
seat. The sensor may not function
properly because the additional seat
cushion could cause sensor
interference.
xIf a small child is seated on the front
passenger's seat, the warning light
may not operate.
Action to be taken
Fasten the seat belts.
▼Seat Belt Warning Light (Rear seat)
(Red)
If the rear seat belts are not fastened
while the ignition is switched ON , the
driver and the passenger are alerted by
the warning light.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-59

perform the applicable procedure
(page 3-8).
▼Power Liftgate Warning Beep*
If system operation precautions are
necessary, the driver is notified by the
warning sound.
Warning beep What to check
The beep sounds 3
timesThe conditions re-
quired for the power
liftgate to operate have
not been met, such as
an object being stuck
in the liftgate.
The beep sound con-
tinuesThe vehicle is being
driven with the liftgate
open. Stop the vehicle
and close the liftgate.
▼Low Fuel Warning Beep
When the low fuel warning light
flashes, a warning beep is activated
once at the same time.
▼Electronic Steering Lock Warning
Beep
The warning beep operates if the
steering wheel is not unlocked after the
push button start is pressed. (page
4-4)
▼Brake System Warning Beep (With
M Hybrid)
A warning beep is activated if a
problem with the brake system occurs
and the brakes may not work as
intended. Decelerate the vehicle while
checking the safety of the surrounding
area, and park the vehicle in a safe
place. After stopping the vehicle,
contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼Brake Override Warning Beep
A warning beep is activated when the
accelerator pedal and brake pedal are
depressed at the same time while
driving. Only depress the brake pedal.
▼Vehicle Problem Warning Beep
If any of the following problems occur,
a warning beep is activated. Check the
information regarding the warning
indication in the instrument cluster or
on the centre display.
xAutomatic transmission problemxIncrease in automatic transmission
internal temperature
xM Hybrid problemxBrake fluid amount decreasexEngine oil level sensor problemxElectric Parking Brake (EPB) problemxEngine hydraulic pressure decreasexEngine coolant temperature increasexEngine system problem
▼Shift Position Warning Beep
A sound is activated when the push
button start is pressed while the
selector lever is in a position other
than P, and the ignition is switched to
ACC. Check the selector lever
position.
▼Ignition Not Off Reminder
Warning Beep (With M Hybrid)
A warning beep is activated
continuously if the driver's door is
opened with the selector lever in a
position other than the P or N
position. Shift the selector lever to the
P or N position, or close the driver's
door.
▼i-stop Warning Beep*
xIf the driver's door is opened while
engine idling is stopped, the warning
sound operates to notify the driver
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-69

▼Lubricant Quality
Engine oil*1Europe and Taiwan Except Europe and Taiwan
SKYACTIV-G 2.0,
SKYACTIV-G 2.5Recommended Oils
*2Oil Quality
Mazda Original Oil Supra-X 0W-20
API SL or higher, or
ILSAC GF-III or higher Mazda Original Oil Ultra 5W-30
Alternative Oil Quality
*3
API SN*4 or higher, or ACEA
A5/B50W-20
5W-30
SKYACTIV-X 2.0Recommended Oils
*2Oil Quality
Mazda Original Oil Supra-X 0W-20
API SN or higher
Alternative Oil Quality
*3
API SN or higher 0W-20
SKYACTIV-D 1.8Recommended Oils
*2Oil Quality
Mazda Original Oil Supra DPF 0W-30
ACEA C3
0W-30/5W-30 Mazda Original Oil Ultra DPF 5W-30
Alternative Oil Quality
*3
ACEA C30W-30
5W-30
*1 Refer to Recommended Oil on page 6-24.*2 Mazda Original Oils are specially designed/tested for the respective engine. For optimum
performance we recommend to use Mazda Original Oils at all times.
*3 If you are unable to find a Mazda Original Oil, alternative oils meeting the listed specification may
also be used.
*4 Use API SM or higher in Kazakhstan.
Do not use oils which do not meet the above specification or requirements. Use of unsuitable oil may
lead to engine damage which is not covered by the Mazda Warranty.
Lubricant Classification
Coolant FL-22 type
Manual transmission oil
Mazda Long Life Gear Oil G7
*1
Automatic transmission
fluidSKYACTIV-G 2.0, SKYAC-
TIV-G 2.5, SKYACTIV-D
1.8Mazda Original Oil ATF-FZ
SKYACTIV-X 2.0 Mazda Original Oil ATF-A7
Transfer case oil Mazda Long Life Hypoid Gear Oil SG1
Rear differential oil Mazda Long Life Hypoid Gear Oil SG1
Specifications
Specifications
9-6

Lubricant Classification
Brake/Clutch fluidWith M Hybrid Mazda Genuine Brake Fluid or equivalent
Without M Hybrid SAE J1703 or FMVSS116 DOT-3 or DOT-4
*1 Mazda Long Life Gear Oil G7 is superior oil for low fuel cost and optimum shift-feel. Using Mazda
Long Life Gear Oil G7 is recommended.
If Mazda Long Life Gear Oil G7 cannot be obtained, use standard oil (API Service GL-4 (SAE
75W-80)).
▼Cleaner
Cleaner Classification
Deposit Cleaner
*1Mazda genuine deposit cleaner
(K002 W0 001)
*1 Use Mazda genuine deposit cleaner. Using non-genuine deposit cleaner would cause internal failure
of the fuel system. Refer to 3-30, 6-3, 6-6 for the details.
▼Capacities
(Approximate Quantities)
Item Capacity
Engine oilSKYACTIV-G 2.0With oil filter replacement 4.2 L (4.4 US qt, 3.7 Imp qt)
Without oil filter replacement 4.0 L (4.2 US qt, 3.5 Imp qt)
SKYACTIV-G 2.5With oil filter replacement 4.5 L (4.8 US qt, 4.0 Imp qt)
Without oil filter replacement 4.3 L (4.5 US qt, 3.8 Imp qt)
SKYACTIV-X 2.0With oil filter replacement 4.6 L (4.9 US qt, 4.0 Imp qt)
Without oil filter replacement 4.4 L (4.6 US qt, 3.9 Imp qt)
SKYACTIV-D 1.8With oil filter replacement 5.1 L (5.4 US qt, 4.5 Imp qt)
Without oil filter replacement 4.7 L (5.0 US qt, 4.1 Imp qt)
Specifications
Specifications
9-7