2019 MAZDA MODEL CX-30 oil temperature

▼Plastic Part Maintenance
xWhen cleaning the plastic lenses of
the lights, do not use petrol, paraffin,
rectified spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these
chemical agents can discolour or
damage the surfaces resulting in a
significant loss in functionality. If
plastic parts become inadvertently
exposed to any of these chemical
agents, flush with water immediately.
xIf plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fluids such as
petrol, oil, engine coolant, or battery
fluid, it could cause discolouration,
staining, or paint peeling. Wipe off
any such chemical agents or fluids
using a soft cloth immediately.
xHigh water temperature and high
water pressure car washers are
available depending on the type of
high pressure car washer device. If
the car washer nozzle is put too
close to the vehicle or aimed at one
area for an extended period of time,
it could deform plastic parts or
damage the paint.
xDo not use wax containing
compounds (polish). Otherwise, it
could result in paint damage.
xIn addition, do not use an electrical
or air tool to apply wax. Otherwise,
the frictional heat generated could
result in deformation of plastic parts
or paint damage.
Interior Care
▼Interior Care
WARNING
Do not spray water into the vehicle
cabin:
Spraying water into the vehicle cabin is
dangerous as electrical devices such as
the audio and switches could get wet
resulting in a malfunction or vehicle
fire.
NOTE
xDo not wipe the interior using
alcohol, chlorine bleach, or organic
solvents such as thinner, benzene,
and petrol. Otherwise, it may cause
discolouration or stains.
xRubbing hard with a stiff brush or
cloth may cause damage.
If the vehicle interior becomes soiled
by any of the following , wipe it off
immediately using a soft cloth.
Leaving it uncleaned could cause
discolouration, stains, cracks, or
peeling of the coating , and it will make
it hard to wipe off later.
xBeverage or fragrancexGrease or oilxSoiling
▼Seat Belt Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked
in a mild detergent (approx. 5%)
diluted with water.
2. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
3. Before retracting seat belts which
have been pulled out for cleaning,
dry them off thoroughly and make
Maintenance and Care
Appearance Care
6-59

xExposure to direct sunlight for long
periods may cause deterioration and
shrinkage. When parking the car
under direct sunlight for long
periods, shade the interior using
sunshades.
xDo not leave vinyl products on the
leather upholstery for long periods.
They may affect the leather quality
and colouring. If the cabin
temperature becomes hot, the vinyl
may deteriorate and adhere to the
genuine leather.
▼Plastic Part Maintenance
CAUTION
Do not use polishing agents.
Depending on the product ingredients,
they could cause discolouration, stains,
cracks or peeling of the coating.
▼Instrument Panel Top (Soft pad)
Maintenance
Extremely soft material is used for the
soft pad surface. If the soft pad surface
is rubbed harshly with a dry cloth, it
could result in the surface being
damaged and leaving white scratch
marks.
1. Wipe the soiled area with a soft
cloth soaked in a mild detergent
(approx. 5%) diluted with water.
2. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
▼Active Driving Display
Maintenance*
The dust-proof sheet has a coating.
When cleaning , do not use a hard or
rough-surface cloth, or cleaning
detergent. In addition, if a chemical
solvent gets on the active driving
display, wipe it off immediately. The
dust-proof sheet could be damaged
and the surface coating could be
scratched. Use a fine, soft cloth such as
those used for cleaning eyeglasses.
NOTE
Use of compressed air when cleaning
the dust-proof sheet is recommended.
▼Panel Maintenance
If a panel becomes soiled, wipe it off
with a soft cloth soaked in clean water
and thoroughly wrung out.
If some areas require further cleaning ,
use the following procedure:
1. Wipe the soiled area with a soft
cloth soaked in a mild detergent
(approx. 5 %) diluted with water.
2. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
NOTE
Be particularly careful when cleaning
shiny surface panels and metallic parts
such as plating as they can be
scratched easily.
▼Cleaning the Window Interiors
If the windows become covered with
an oily, greasy, or waxy
film, clean
them with glass cleaner. Follow the
directions on the container.
CAUTION
¾Do not scrape or scratch the inside
of the window glass. It could
damage the thermal filaments and
the aerial lines.
¾When washing the inside of the
window glass, use a soft cloth
dampened in lukewarm water, gently
wiping the thermal filaments and the
aerial lines.
Maintenance and Care
Appearance Care
*Some models.6-61

1. Drive to the side of the road and
park off the right-of-way on level
ground.
2. Turn off the engine and wait 5
minutes for the oil to drain back
into the sump.
3. Inspect the engine oil level (page
6-27). If it's low, add the
appropriate amount of engine oil
while being careful not to overfill.
CAUTION
Do not run the engine if the oil
level is low. Otherwise, it could
result in extensive engine damage.
4. Start the engine and check the
warning light.

If the light remains illuminated even
though the oil level is normal or after
adding oil, stop the engine
immediately and have your vehicle
towed to an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼High Engine Coolant Temperature
Warning Indication
Displays if the engine coolant
temperature has increased excessively.
“Elevated Engine Coolant Temp. Drive
Slowly” displayed
Drive slowly to reduce engine load
until you can find a safe place to stop
the vehicle and wait for the engine to
cool down.
“Excessive Engine Coolant Temp. Stop
the Vehicle in a Safe Location”
displayed
This indicates the possibility of
overheating. Park the vehicle in a safe
place immediately and stop the
engine.
Refer to Overheating on page 7-44.
CAUTION
Do not drive the vehicle with the high
engine coolant temperature warning
light illuminated. Otherwise, it could
result in damage to the engine.
▼Power Steering Malfunction
Indication/Indicator Light
The message is displayed if the electric
power steering has a malfunction.
If the message is displayed, stop the
vehicle in a safe place and do not
operate the steering wheel. There is no
problem if the indication turns off
when the engine is restarted after
some time has passed. If the indication
displays even after the engine is
restarted, contact an expert repairer
(we recommend an Authorised Mazda
Repairer) if the message is displayed
continuously.
NOTE
xIf the message is displayed, the
power steering will not operate
normally. In this case, the steering
wheel can still be operated,
however, the operation may feel
heavy compared to normal, or the
steering wheel could vibrate when
turning.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-51

at an expert repairer (we recommend
an Authorised Mazda Repairer).
xWhen there is a malfunction in the
AWD system.
“Excessive AWD System Load. Drive
Slowly Until Warning Light Turns Off.
Vehicle Now in Front Wheel Drive” is
displayed/When the light is flashing
The indication is displayed/the light
flashes under the following conditions.
Park the vehicle in a safe place and
check that the warning indication light
turns
off/ the warning light stops
flashing, and then drive the vehicle.
Contact an expert repairer (we
recommend an Authorised Mazda
Repairer) if the indication is
continuously displayed.
xWhen the differential oil temperature
is excessively high.
xWhen there is a large difference
between the front and rear wheel
rotation, such as when trying to
remove the vehicle from mud.
“Mismatched Tyre Diameters. Vehicle
Now in Front Wheel Drive” is
displayed/When the light is turned on
The indication is displayed/the light
turns on under the following
conditions. Inspect the tyre sizes or
tyre pressures on all 4 wheels. Contact
an expert repairer (we recommend an
Authorised Mazda Repairer) if the
indication remains on or the warning
light remains illuminated.
xWhen any of the tyre diameter is
different.
xWhen any of the tyre pressure is
incorrect.
▼120 km/h Warning Light*
The 120 km/h warning light
illuminates when the vehicle speed
exceeds 120 km/h.
Action to be taken
Lower the vehicle speed.
▼Tyre Pressure Monitoring System
(TPMS) Warning Indication/
Warning Light (Flashing)
*
If there is a problem with the TPMS or
the voltage of a tyre pressure sensor
decreases, the TPMS warning light
flashes and a message is displayed on
the multi-information display. Have
your vehicle inspected by an expert
repairer (we recommend an
Authorised Mazda Repairer).
WARNING
Do not drive the vehicle at high
speeds if the TPMS warning light turns
on or flashes:
Driving the vehicle at high speeds
while the TPMS warning light is turned
on or
flashing is dangerous because
the brake performance and the
steering wheel operability will be
reduced. If the vehicle is driven at high
speeds or the brakes are suddenly
applied, it could lead to an accident.
Gradually apply the brakes to lower the
vehicle's speed.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-57

perform the applicable procedure
(page 3-8).
▼Power Liftgate Warning Beep*
If system operation precautions are
necessary, the driver is notified by the
warning sound.
Warning beep What to check
The beep sounds 3
timesThe conditions re-
quired for the power
liftgate to operate have
not been met, such as
an object being stuck
in the liftgate.
The beep sound con-
tinuesThe vehicle is being
driven with the liftgate
open. Stop the vehicle
and close the liftgate.
▼Low Fuel Warning Beep
When the low fuel warning light
flashes, a warning beep is activated
once at the same time.
▼Electronic Steering Lock Warning
Beep
The warning beep operates if the
steering wheel is not unlocked after the
push button start is pressed. (page
4-4)
▼Brake System Warning Beep (With
M Hybrid)
A warning beep is activated if a
problem with the brake system occurs
and the brakes may not work as
intended. Decelerate the vehicle while
checking the safety of the surrounding
area, and park the vehicle in a safe
place. After stopping the vehicle,
contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼Brake Override Warning Beep
A warning beep is activated when the
accelerator pedal and brake pedal are
depressed at the same time while
driving. Only depress the brake pedal.
▼Vehicle Problem Warning Beep
If any of the following problems occur,
a warning beep is activated. Check the
information regarding the warning
indication in the instrument cluster or
on the centre display.
xAutomatic transmission problemxIncrease in automatic transmission
internal temperature
xM Hybrid problemxBrake fluid amount decreasexEngine oil level sensor problemxElectric Parking Brake (EPB) problemxEngine hydraulic pressure decreasexEngine coolant temperature increasexEngine system problem
▼Shift Position Warning Beep
A sound is activated when the push
button start is pressed while the
selector lever is in a position other
than P, and the ignition is switched to
ACC. Check the selector lever
position.
▼Ignition Not Off Reminder
Warning Beep (With M Hybrid)
A warning beep is activated
continuously if the driver's door is
opened with the selector lever in a
position other than the P or N
position. Shift the selector lever to the
P or N position, or close the driver's
door.
▼i-stop Warning Beep*
xIf the driver's door is opened while
engine idling is stopped, the warning
sound operates to notify the driver
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-69

Index
Washer................................ 4-65
Headlight Washer...................... 4-65
Head Restraint.......................... 2-15
High Beam Control System
(HBC)....................................... 4-99
High Beam Control System (HBC)
indicator light (green)......... 4-100
Hill Launch Assist (HLA)............. 4-79
Horn........................................ 4-67
I
If a Warning Light Turns On or
Flashes......................................7-49
If the Active Driving Display Does Not
Operate.................................... 7-74
Ignition Not Off Reminder Warning
Beep.........................................7-69
Ignition Not Switched Off (STOP)
Warning Beep........................... 7-67
Ignition Switch............................ 4-4
Illuminated Entry System............ 5-34
Immobilizer System................... 3-47
Inspecting Brake/Clutch Fluid
Level.........................................6-30
Inspecting Coolant Level............ 6-28
Inspecting Engine Oil Level.........6-27
Inspecting Washer Fluid Level..... 6-31
Instrument Cluster..................... 4-21
Average fuel economy...........4-29
Current fuel economy........... 4-29
Deceleration regeneration charge
display................................. 4-30
Distance-to-empty................4-28
Engine coolant temperature
gauge...................................4-25
Fuel gauge........................... 4-26
Indication/indicator lights..... 4-34
Instrument panel
illumination..........................4-27
i-ACTIVSENSE display........... 4-30
Message Display................... 4-31
Message indicated on multi-
information display............... 7-63
Multi-information display...... 4-23
Odometer............................ 4-25
Outside temperature
display................................. 4-28
Speedometer....................... 4-21
Tachometer.......................... 4-21
Trip meter............................ 4-25
Vehicle speed alarm............. 4-30
Warning indication/warning
lights....................................4-32
Intelligent Speed Assistance
(ISA)....................................... 4-170
Activation/deactivation.......4-172
Intelligent Speed Assistance (ISA)
display............................... 4-172
Intelligent Speed Assistance (ISA)
set indication (green).......... 4-171
Intelligent Speed Assistance (ISA)
standby indication (white)... 4-171
Setting the system...............4-173
Temporarily cancelling the
system............................... 4-174
Interior Care............................. 6-59
Active driving display
maintenance........................ 6-61
Cleaning the window
interiors............................... 6-61
Instrument panel top (Soft pad)
maintenance........................ 6-61
Leather upholstery
maintenance........................ 6-60
Panel maintenance............... 6-61
Plastic part maintenance....... 6-61
Seat belt maintenance.......... 6-59
Upholstery maintenance....... 6-60
Vinyl upholstery
maintenance........................ 6-60
Interior Lights............................ 5-33
10-5

Index
Outside mirrors.................... 3-36
Rearview mirror.................... 3-39
Mirror Defogger........................ 4-67
Multi-information Display.......... 4-23
M Hybrid.................................. 4-86
O
Off-Road Traction Assist............ 4-84
Off-Road Traction Assist
indicator light....................... 4-84
Off-Road Traction
Assist switch......................... 4-84
Outside Mirrors.........................3-36
Outside temperature warning
beep........................................ 7-70
Overhead Console.................... 5-39
Overhead Lights........................ 5-33
Overheating.............................. 7-44
Owner Maintenance
Closing the bonnet............... 6-18
Engine compartment
overview.............................. 6-19
Key battery replacement........6-39
Opening the bonnet............. 6-17
Owner maintenance
precautions.......................... 6-16
P
Parking Brake............................ 4-70
Parking Sensor System............. 4-252
Park assist sensor system
operation........................... 4-255
Sensor detection range........4-254
Petrol Particulate Filter............. 4-236
Power Liftgate........................... 3-22
Power Liftgate Warning Beep...... 7-69
Power Steering.......................... 4-93
Power Windows........................ 3-41
R
Rearview Mirror........................ 3-39
Rear Coat Hooks....................... 5-39
Rear Cross Traffic Alert (RCTA) ...........
.............................................. 4-126
Rear Cross Traffic Alert (RCTA)
Warning Beep........................... 7-71
Rear Door Child Safety Locks..... 3-20
Rear Fog Light........................... 4-59
Rear Side Radar Sensor............ 4-224
Rear View Monitor.................. 4-238
Displayable range on the
screen................................ 4-240
Rear view monitor
operation........................... 4-242
Rear view parking camera
location............................. 4-239
Switching to the rear view monitor
display............................... 4-239
Variance between actual road
conditions and displayed
image................................ 4-249
Viewing the display.............4-241
Rear window
Rear Window Defogger......... 4-66
Rear Window Defogger............. 4-66
Rear Window Washer................ 4-64
Rear Window Wiper.................. 4-64
Recommended Oil.................... 6-24
Registering Your Vehicle in A Foreign
Country...................................... 8-2
Replacement
Fuse..................................... 6-46
Key battery........................... 6-39
Light bulbs........................... 6-44
Tyres.................................... 6-42
Wheel.................................. 6-43
Wiper.................................. 6-32
Roadside Emergency Triangle
Retaining Strap.......................... 7-23
10-8