2019 MAZDA MODEL CX-30 turn signal

Signal Indicator Refer to
(Green)
*Mazda Radar Cruise Control (MRCC) Set Indication4-134
*Mazda Radar Cruise Control with Stop & Go function (MRCC with
Stop & Go function) Set Indication4-143
*Cruising &
Tra ffi c Support (CTS) Set Indication4-154
*Smart Brake Support (SBS) OFF Indicator Light*1
Smart Brake
Support (SBS)
4-177
Smart Brake
Support [Rear]
(SBS-R)
4-180
Smart Brake
Support [Rear
Crossing]
(SBS-RC)
4-184
(White)
*Intelligent Speed Assistance (ISA) Standby Indication4-171
*Adjustable Speed Limiter (ASL) Standby Indication4-167
(Green)
*Intelligent Speed Assistance (ISA) Set Indication4-171
*Adjustable Speed Limiter (ASL) Set Indication4-167
(White)
*Cruise Standby Indication4-228
(Green)
*Cruise Set Indication4-228
*1 The light turns on when the ignition is switched on for an operation check, and
turns off a few seconds later or when the engine is started. If the light does not
turn on or remains turned on, have the vehicle inspected at an expert repairer
(we recommend an Authorised Mazda Repairer).
*2 The light turns on continuously when the parking brake is applied.
▼Wrench Indication/Indicator LightThe wrench indication/indicator light
is displayed/turns on under the
following conditions.
xWhen the preset maintenance
period has arrived.
When Driving
Instrument Cluster and Display
*Some models.4-37

▼Indicators
1. Manual shift mode indication
2. Gear position indication
Manual shift mode indication
In manual shift mode, the “M” of the
shift position indication in the
instrument panel illuminates.
Gear position indication
The numeral for the selected gear
illuminates.

NOTE
xIf the gears cannot be shifted down
when driving at higher speeds, the
gear position indication will
flash
twice to signal that the gears cannot
be shifted down (to protect the
transmission).
xIf the automatic transmission fluid
(ATF) temperature becomes too
high, there is the possibility that the
transmission will switch to automatic
shift mode, cancelling manual shift
mode and turning off the gear
position indication illumination. This
is a normal function to protect the
AT. After the ATF temperature has
decreased, the gear position
indication illumination turns back on
and driving in manual shift mode is
restored.
x(SKYACTIV-D 1.8 (European
model))
If the engine oil temperature
becomes too high, there is the
possibility that the transmission will
switch to automatic shift mode,
cancelling manual shift mode and
turning off the gear position
indicator illumination. After the
engine oil temperature has
decreased, the gear position
indicator illumination turns back on
and driving in manual shift mode is
restored.
▼Gear Shift Indicator (GSI)*
The GSI supports you to obtain
optimum fuel economy and smooth
driving. It displays the selected gear
position in the instrument cluster as
well as notifies the driver to change to
the most suitable gear position
corresponding to the actual driving
condition.

1. Selected gear position
2. Suitable gear position
Indication Condition
NumeralThe selected gear position is
displayed.
and numer-
alShift up or down to the indi-
cated gear position is recom-
mended.
When Driving
Automatic Transmission
*Some models.4-47

The following lights turn on when the
leaving home light is operated.
Low beams, Position lights, Tail lights,
Number plate lights.
To turn on the lights
When the ignition switch and the
headlight switch are in the following
conditions, the headlights will
illuminate when the transmitter unlock
button is pressed and the vehicle
receives the transmitter signal. The
headlights turn off after a certain
period of time has elapsed (30
seconds).
xIgnition switch: off
xHeadlight switch: AUTO, , or
1. Lock button
2. Unlock button
NOTE
xOperation of the leaving home light
can be turned on or
off.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
xWhen the transmitter lock button is
pressed and the vehicle receives the
transmitter signal, the headlights turn
off.
xWhen the headlight switch is turned
to the OFF position, the headlights
turn off.
▼Headlight Levelling
The number of passengers and weight
of cargo in the luggage Compartment
change the angle of the headlights.
The angle of the headlights will be
automatically adjusted when turning
on the headlights.
A system malfunction or operation
conditions are indicated by a warning.
Refer to Exterior Light Warning
Indication/Warning Light on page
7-58.
▼Running Lights*
Some countries require moving
vehicles to have their lights on (running
lights) during the daytime.

The running lights turn on or off
automatically.

NOTE
(Except countries prohibited by law)
The running lights can be deactivated.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When Driving
Switches and Controls
4-58*Some models.

Turn and Lane-Change
Signals
▼Turn and Lane-Change Signals
The ignition must be switched ON to
use the turn and lane-change signals.
▼Direction Indicators
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel
after the turn is completed.

If the indicator light continues to flash
after a turn, manually return the lever
to its original position.
1. Right turn
2. Right lane change
3. OFF
4. Left lane change
5. Left turn

The direction indicators in the
instrument cluster flash according to
the operation of the direction indicator
lever to show which signal is working.

NOTE
xThere may be a problem with the
direction indicator lights if they do
not flash but remain turned on, or
they flash abnormally. Have your
vehicle inspected by an expert
repairer (we recommend an
Authorised Mazda Repairer).
xA personalised function is available
to change the turn indicator sound
volume.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Lane-Change Signals
Move the lever halfway toward the
direction of the lane changeŠuntil the
indicator
flashesŠ and hold it there. It
will return to the off position when
released.
▼Three-Flash Turn Signal
After releasing the direction indicator
lever from the halfway point, the
direction indicator
flashes 3 times. The
operation can be cancelled by moving
the lever in the direction opposite to
which it was operated.
NOTE
The three-flash turn signal function can
be switched to on/off using the
personalisation function.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When Driving
Switches and Controls
4-60

Hazard Warning Flasher
▼Hazard Warning Flasher
The hazard warning lights should
always be used when you stop on or
near a roadway in an emergency.

The hazard warning lights warn other
drivers that your vehicle is a traffic
hazard and that they must take
extreme caution when near it.

Depress the hazard warning flasher
and all the direction indicators will
flash. The hazard warning indicator
lights in the instrument cluster flash
simultaneously.
NOTE
xThe direction indicators do not work
when the hazard warning lights are
on.
xCheck local regulations about the
use of hazard warning lights while
the vehicle is being towed to verify
that it is not in violation of the law.
xIf the brake pedal is depressed while
driving on slippery roads, the
emergency stop signal system could
operate causing all the turn and lane
change signals to flash. Refer to
Emergency Stop Signal System on
page 4-78.
xWhile the emergency stop signal
system is operating, all the direction
indicators automatically flash rapidly
to caution the driver of a vehicle
following behind your vehicle of a
sudden braking situation. Refer to
Emergency Stop Signal System on
page 4-78.
When Driving
Switches and Controls
4-68

xThere is a problem with the
AUTOHOLD function.Emergency Stop Signal
System
▼Emergency Stop Signal System
If you apply the brakes suddenly while
driving at a speed of about 55 km/h
(34 mph) or faster, the emergency stop
signal system automatically and rapidly
flashes all the direction indicator lights
to caution drivers behind your vehicle
of the sudden braking situation.
NOTE
xFlashing
When you bring your vehicle to a
complete stop while all the direction
indicator lights are flashing rapidly,
the rapid
flashing of all the direction
indicator lights changes back to the
normal flashing pattern. The
direction indicator lights turn off
when you release your foot from the
brake pedal.
xOperation
xWhen the ABS operates, the
emergency stop signal system is
more likely to operate. Therefore, if
the brake pedal is depressed on a
slippery road, all of the direction
indicator lights may
flash.
xThe emergency stop signal system
does not operate when the hazard
warning light switch is pressed.
When Driving
Brake
4-78

High Beam Control
System (HBC)
*
▼High Beam Control System (HBC)
The HBC determines the conditions in
front of the vehicle using the Forward
Sensing Camera (FSC) while driving in
darkness to automatically switch the
headlights between high and low
beams.
Refer to Forward Sensing Camera
(FSC) on page 4-216.
While driving the vehicle at a speed of
about 30 km/h (19 mph) or more, the
headlights are switched to high beams
when there are no vehicles ahead or
approaching in the opposite direction.
The system switches the headlights to
low beams when one of the following
occurs:
xThe system detects a vehicle or the
headlights/lights of a vehicle
approaching in the opposite
direction.
xThe vehicle is driven on roads lined
with streetlamps or on roads in
well-lit cities and towns.
xThe vehicle is driven at less than
about 20 km/h (12 mph).
xThe headlight high-beam indicator
light turns on while the high beams
are on.
1. Forward Sensing Camera (FSC)*1
*1 The recognition distance of the Forward
Sensing Camera (FSC) varies according to
the surrounding conditions.
The warning light turns on when the
system has a malfunction.
Refer to High Beam Control System
(HBC) Warning Indication/Warning
Light (Amber) on page 7-58.
CAUTION
¾Do not adjust the vehicle height,
modify the headlight units, or
remove the camera, otherwise the
system will not operate normally.
¾Do not rely excessively on the HBC
and drive the vehicle while paying
sufficient attention to safety. Switch
the headlights between the high
beams and low beams manually if
necessary.
NOTE
The timing in which the system
switches the headlights changes under
the following conditions. If the system
does not switch the headlights
appropriately, manually switch
between high and low beams
according to the visibility as well as
road and traffic conditions.
xWhen there are sources of light in
the area such as street lamps,
illuminated signboards, and traffic
signals.
xWhen there are reflective objects in
the surrounding area such as
reflective plates and signs.
xWhen visibility is reduced under rain,
snow and foggy conditions.
xWhen driving on roads with sharp
turn or hilly terrain.
xWhen the headlights/rear lamps of
vehicles in front of you or in the
opposite lane are dim or not
illuminated.
When Driving
i-ACTIVSENSE
*Some models.4-99

xWhen there are other sources of light
in the area such as street lamps,
illuminated signboards, and traffic
signals.
xWhen there are reflective objects in
the surrounding area such as
reflective plates and signs.
xWhen visibility is reduced under rain,
snow and foggy conditions.
xWhen driving on roads with sharp
curves or undulations.
xWhen the headlights/rear lamps of
vehicles ahead or in the opposite
lane are dim or not illuminated.
xWhen there is insufficient darkness
such as at dawn or dusk.
xWhen the luggage compartment is
loaded with heavy objects or the rear
passenger seats are occupied.
xWhen visibility is reduced due to a
vehicle ahead spraying water from its
tyres onto your windscreen.
▼To Operate the System
The ALH operates to control Glare-Free
High Beam, Wide-Range Low Beam
and Highway Mode automatically after
the ignition is switched ON and the
headlight switch is in the
and
low beam position.
The ALH determines that it is dark
based on the brightness of the
surrounding area. At the same time,
the ALH indicator light (green) in the
instrument cluster illuminates.
NOTE
Operation of the ALH function can be
disabled.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Manual Switching
Switching to low beams
Switch the headlight switch to the
position, or press the ALH switch.
The ALH indicator light (green) turns
off.
1. ALH switch

If the ALH is turned off using the ALH
switch, press the ALH switch again to
turn the ALH back on.
Switching to high beams
Shift the lever to the high beam
position.
The ALH indicator light (green) turns
off and the headlight high-beam
indicator light is illuminated.
When Driving
i-ACTIVSENSE
4-102