2019 MAZDA MODEL CX-30 engine

Window and Headlight
Washer Fluid
▼Inspecting Washer Fluid Level
WARNING
Use only windscreen washer fluid or
plain water in the reservoir:
Using radiator antifreeze as washer
fluid is dangerous. If sprayed on the
windscreen, it will dirty the
windscreen, affect your visibility, and
could result in an accident.
Inspect fluid level in the washer fluid
reservoir; add fluid if necessary.

The top of the float should be between
F and E.

Use plain water if washer
fluid is
unavailable.
But use only washer fluid in cold
weather to prevent it from freezing.
NOTE
Front and rear washer
fluid is supplied
from the same reservoir.
Body Lubrication
▼Body Lubrication
All moving points of the body, such as
door and bonnet hinges and locks,
should be lubricated each time the
engine oil is changed. Use a
nonfreezing lubricant on locks during
cold weather.

Make sure the bonnet's secondary
latch keeps the bonnet from opening
when the primary latch is released.
Maintenance and Care
Owner Maintenance
6-31

▼Inspecting Electrolyte Level
A low level of electrolyte fluid will
cause the battery to discharge quickly.

1. Upper level
2. Lower level
Inspect the electrolyte level at least
once a week. If it is low, remove the
caps and add enough distilled water to
bring the level between the upper and
lower level (illustration).

Do not overfill.
Examine the specific gravity of the
electrolyte with a hydrometer,
especially during cold weather. If it is
low, recharge the battery.
▼Battery Recharging
NOTE
xBefore performing maintenance or
recharging the battery, turn off all
accessories and stop the engine.
xTo disconnect the battery, remove
the negative lead first. Install it last
when connecting the battery.
xBe sure to remove the caps before
recharging the battery.
xDo not quick-charge the battery.
xIf the battery quickly discharges
because, for example, the lights
were left on too long with the engine
off, slow-charge it as required by
battery size and charger capacity.
xIf the battery gradually discharges
because of high electric load while
the vehicle is being used, recharge it
as required by battery size and
charger capacity.
▼Battery Replacement
Contact an expert repairer (we
recommend an Authorised Mazda
Repairer) for a battery replacement
purchase.
Maintenance and Care
Owner Maintenance
6-38

xVanity mirror lights
Refer to Vanity Mirrors on page
5-32.
xFront overhead lights/front map
lights, rear overhead light, and
luggage compartment light
Refer to Interior Lights on page
5-33.
▼Replacing Exterior Light Bulbs
The exterior lights have either LEDs or
normal bulbs.
Only the bulb for a running lights (type
B) can be replaced.
LED type
xHeadlightsxRunning lights (Type A)xPosition lightsxFront direction indicator lightsxSide direction indicator lightsxHigh-mount brake lightxRear direction indicator lightsxBrake lightsxTail lightsxReverse lightsxRear fog lightsxNumber plate lights
The LED bulb cannot be replaced as a
single unit because it is an integrated
unit.
The LED bulb has to be replaced with
the unit. We recommend an expert
repairer (we recommend an
Authorised Mazda Repairer) if the
replacement is necessary.
Bulb type
Running lights (Type B)
1. Make sure the ignition is switched
off, and the headlight switch is off.
2. If you are changing the left bulb,
start the engine, turn the steering
wheel all the way to the right, and
turn off engine. If you are changing
the right bulb, turn the steering
wheel to the left.
3. Pull the centre of each plastic
retainer and remove the retainers.
1. Removal
2. Installation
4. Pull the centre of each plastic
retainer and remove the retainers.
1. Removal
2. Installation
5. Turn the screw anticlockwise and
remove it, and then partially peel
back the mudguard.
Maintenance and Care
Owner Maintenance
6-45

block located in the engine
compartment.
4. Inspect the fuse and replace it if it is
blown.
1. Normal
2. Blown

5. Insert a new fuse of the same
amperage rating , and make sure it
fits tightly. If it does not
fit tightly,
have an expert install it. Consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
If you have no spare fuses, borrow
one of the same rating from a
circuit not essential to vehicle
operation, such as the audio or
accessory socket circuit.
CAUTION
Always replace a fuse with a
genuine Mazda fuse or equivalent
of the same rating. Otherwise, you
may damage the electric system.
6. Reinstall the cover and make sure
that it is securely installed.
Replacing the fuses under the bonnet
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the
fuse block under the bonnet.
If a fuse is blown, it must be replaced.
Follow these steps:

1. Make sure the ignition is switched
off, and other switches are
off.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is
blown, replace it with a new one of
the same amperage rating.
1. Normal
2. Blown

Maintenance and Care
Owner Maintenance
6-47

▼Fuse Panel Description
Fuse block (Engine compartment)
No.FUSE RAT-
INGPROTECTED COMPONENT
F1ŠŠ
F2 20 A
Windscreen wiper de-icer
*
F330 A
Engine control system*
20 A/30 A
Injector*
F4 20 A
S-VT*
F5 40 A Engine control system
F6 20 A
S-VT
*
Maintenance and Care
Owner Maintenance
*Some models.6-49

No.FUSE RAT-
INGPROTECTED COMPONENT
F715 A
Fuel warmer
*
20 A
Fuel pump*
F8 15 A Engine control system
F9 15 A
Transmission control system
*
F10 15 A Engine control system
F11 7.5 A Air conditioner
F12 15 A Engine control system
F13 15 A
NOx sensor
*
F14 20 A
Front seat warmer*
F15 20 A
Headlight washer*
F16 15 A For protection of various circuits
F17ŠŠ
F18 15 A Accessory sockets
F19 60 A Power steering system
F20 15 A Headlight (LH) 1
F21 15 A Headlight (RH) 1
F22 15 A Keyless system
F23 30 A ABS, Dynamic stability control system
F24 15 A Headlight (LH) 2
F25 15 A Headlight (RH) 2
F26 7.5 A On board diagnostics
F27 25 A For protection of various circuits
F28 25 A For protection of various circuits
F29 15 A Windscreen washer
F30ŠŠ
F31 15 A Horn
F32 15 A Headlights
F33ŠŠ
F34ŠŠ
F35 50A ABS, Dynamic stability control system
F36ŠŠ
F37 40 A Rear window defogger
F38 50 A For protection of various circuits
Maintenance and Care
Owner Maintenance
6-50*Some models.

No.FUSE RAT-
INGPROTECTED COMPONENT
F39ŠŠ
F40 40 A Air conditioner
F41ŠŠ
F42 20 A Windscreen wiper
F43 30 A
Cooling fan
*
F44 30 A Starter
F45 10 A Engine control system
F46 15 A Audio
F47 15 A For protection of various circuits
F48 7.5 A Air bag
F49 15 A Instrument cluster
F50 15 A Room light
F51 25 A Audio
F52 10 A
Sunroof
*
F53 15 A Engine control system
F54 15 A i-ACTIVSENSE
F55 50 A
For protection of various circuits
*
F56 50 AŠ
Maintenance and Care
Owner Maintenance
*Some models.6-51

evaporates, the minerals will
concentrate and harden to form white
rings. The rings can damage your
vehicle's finish.
Prevention
It is necessary to wash and wax your
vehicle to preserve its
finish according
to the instructions in this section.
These steps should be taken
immediately after you find water marks
on your vehicle's finish.
Paint Chipping
Occurrence
Paint chipping occurs when gravel
thrown in the air by another vehicle's
tyres hits your vehicle.
How to avoid paint chipping
Keeping a safe distance between you
and the vehicle ahead reduces the
chances of having your paint chipped
by
flying gravel.
NOTE
xThe paint chipping zone varies with
the speed of the vehicle. For
example, when travelling at 90 km/h
(56 mph), the paint chipping zone is
50 m (164 ft).
xIn low temperatures a vehicle's
finish
hardens. This increases the chance of
paint chipping.
xChipped paint can lead to rust
forming on your Mazda. Before this
happens, repair the damage by using
Mazda touch-up paint according to
the instructions in this section.
Failure to repair the affected area
could lead to serious rusting and
expensive repairs.

Follow all label and container
directions when using a chemical
cleaner or polish. Read all warnings
and cautions.
▼Maintaining the Finish
Washing
CAUTION
¾Before lifting the windscreen wiper
blades off the windscreen, always
follow the procedure for moving the
windscreen wiper blades. Otherwise,
a wiper blade, wiper arm, or the
bonnet could be damaged.
Refer to the Replacing Windscreen
Wiper Blades (page 6-32) section for
the procedure on how to move the
windscreen wiper blades to the
service position.
¾When the wiper lever is in the AUTO
position and the ignition is switched
ON, the wipers may move
automatically in the following cases:
¾If the windscreen above the rain
sensor is touched or wiped with a
cloth.
¾If the windscreen is struck with a
hand or other object from either
outside or inside the vehicle.
Keep hands and scrapers clear of the
windscreen when the wiper lever is
in the AUTO position and the
ignition is switched ON as
fingers
could be pinched or the wipers and
wiper blades damaged when the
wipers activate automatically.
If you are going to clean the
windscreen, be sure the wipers are
turned off completely (when it is
most likely that the engine is left
running) this is particularly important
when clearing ice and snow.
Maintenance and Care
Appearance Care
6-55