2019 MAZDA MODEL CX-30 mazda connect

6. If the connection fails, the indicator light (red) turns on and the indicator light
(green) flashes quickly (0.15 second intervals), and the beep sounds
simultaneously.
Make a manual emergency call again.
1. Red (Turns on)
2. Green (Flashes)
NOTE
If a call to the call centre does not connect even though the indicator light shows a
call is possible, make a call to the police or other authority by means other than the
Mazda
ERA-GLONASS.
Manual emergency call cancellation
A manual emergency call can be cancelled even after the Emergency call switch has
been pressed by pressing the switch again, as long as the call with the call centre has
not begun. If the call cannot be cancelled and the call with the call centre has
begun, tell the operator that the call is mistaken.
▼Indicator Light/Beep Sound
The indicator light turns on/flashes and beep sounds are activated to notify the
driver of the system operation status or if there is a problem with the system.
StatusIndicator light
Beep sound
statusOn/flashing conditions
Green Red Flash interval
Diagnosis Turns on Turns onŠŠWhen the ignition is switched
ON, it turns on and then
turns off after a few seconds.
NOTE
A manual emergency call is
not possible during diagnosis.
Normal Turns off Turns offŠŠThe system is operating nor-
mally.
If Trouble Arises
Mazda
ERA-GLONASS
7-19

StatusIndicator light
Beep sound
statusOn/flashing conditions
Green Red Flash interval
Malfunction Turns off Turns onŠ3 beeps
(Slow intermit-
tent sound)
xA system malfunction is
detected.
xThe remaining power of
the built-in battery is low.
CAUTION
If the indicator light (red) re-
mains on constantly, the sys-
tem will not operate normal-
ly. Have the vehicle inspected
at an expert repairer (we rec-
ommend an Authorised Maz-
da Repairer) as soon as possi-
ble.
Call being
made with call
centreFlashes Turns offSlow
(0.5 second
intervals)The beep does
not sound, but
the ringback
tone can be
heard.An emergency call is being
made by the Mazda
ERA-GLONASS.
Vehicle infor-
mation is be-
ing transmittedFlashes Turns
offSomewhat
quick
(0.3 second
intervals)Continuous in-
termittent
soundVehicle information is being
transmitted to the call centre.
Start of voice
callTu r n s o n Tu r n s o ffŠ1 beep
During a voice call with the
call centre.
During voice
callTu r n s o n Tu r n s
offŠŠ
Connection
failureFlashes Turns onQuick
(0.15 second
intervals)3 beeps
(Fast intermit-
tent sound)When an emergency call fails
to connect.
▼Te s t M o d e
The test mode function makes sure that the Mazda ERA-GLONASS can operate
normally.
Have your vehicle tested at an Authorised Mazda Repairer when performing the test
mode.
Method to start test mode
Switch the ignition ON while the parking brake is applied, and wait 2 minutes with
the vehicle stopped.
If Trouble Arises
Mazda
ERA-GLONASS
7-20

¾Do not exceed 80 km/h (50 mph).
¾Avoid driving over obstacles. Also,
do not drive through an automatic
car wash. This tyre's diameter is
smaller than a conventional tyre,
so the ground clearance is
reduced.
¾Do not use a tyre chain on this tyre
because it will not fit properly.
¾Do not use your temporary spare
tyre on any other vehicle, it has
been designed only for your
Mazda.
¾Use only one temporary spare tyre
on your vehicle at the same time.
To remove the spare tyre
1. Remove the luggage mat.

2.(Vehicles with sub-woofer)
Uncouple the sub-woofer
connector.

1. Sub-woofer

NOTE
Extra strength may be required to
uncouple the connector. Be sure to
squeeze the tab firmly.
3.(Vehicles with sub-woofer)
Turn the spare tyre hold-down bolt
anticlockwise and remove the
sub-woofer and the spare tyre.

(Vehicles without sub-woofer)
Turn the spare tyre hold-down bolt
anticlockwise and remove the spare
tyre.

1. Spare tyre hold-down bolt

NOTE
If the spare tyre hold-down bolt
cannot be loosened, hold the edge
of the tyre and turn it anticlockwise
until the spare tyre hold-down bolt
rotates.
To secure the spare tyre
Store the spare tyre in the reverse order
of removal. After storing , verify that the
spare tyre is stored securely.
If Trouble Arises
Flat Tyre
7-26

Location shown in the figure (do not connect to the negative (-) terminal of
the battery)
5. Start the booster vehicle's engine and rev the engine.
6. Start the engine of your vehicle. Run the engines for about 3 minutes to
temporarily charge the battery of your vehicle.
7. Disconnect the jumper leads in the reverse order of their connection.
8. Install the battery cover.
9. Have your vehicle inspected by an expert repairer (we recommend an Authorised
Mazda Repairer) as soon as possible.
If Trouble Arises
Battery Runs Out
7-41

Towing Description
▼Towing Description
We recommend that towing be done
only by an expert repairer (we
recommend an Authorised Mazda
Repairer) or a commercial tow-truck
service.

Proper lifting and towing are necessary
to prevent damage to the vehicle.
Particularly when towing a AWD
vehicle, where all the wheels are
connected to the drive train, proper
transporting of the vehicle is absolutely
essential to avoid damaging the drive
system. Government and local laws
must be followed.
1. Wheel dollies

A towed FWD vehicle should have its
drive wheels (front wheels)
off the
ground. If excessive damage or other
conditions prevent this, use wheel
dollies.

When towing a FWD vehicle with the
rear wheels on the ground, release the
parking brake.
Refer to Electric Parking Brake (EPB) on
page 4-70.

A towed AWD vehicle must have all its
wheels
off the ground.
WARNING
Always tow a AWD vehicle with all
four wheels
off the ground:
Towing a AWD vehicle with either the
front or rear wheels on the ground is
dangerous as the drive train could be
damaged, or the vehicle could trail
away from the tow truck and cause an
accident. If the drive train has been
damaged, transport the vehicle on a
flatbed truck.
CAUTION
¾Do not tow the vehicle pointed
backward with driving wheels on the
ground. This may cause internal
damage to the transmission.
¾Do not tow with sling-type
equipment. This could damage your
vehicle. Use wheel-lift or flatbed
equipment.
If Trouble Arises
Emergency Towing
7-46

▼Brake Override Warning Indication
This message is displayed when the
accelerator pedal and brake pedal are
depressed at the same time while
driving.
Release the accelerator pedal and
depress the brake pedal.
▼Check Engine Indication/Light
If this light illuminates while driving ,
the vehicle may have a problem. It is
important to note the driving
conditions when the light illuminated
and consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
The check engine light may illuminate
in the following cases:
xThe engine's electrical system has a
problem.
xThe emission control system has a
problem.
x(Except SKYACTIV-D 1.8)
xThe fuel tank level being very low
or approaching empty.
xThe
fuel-filler cap is missing or not
tightened securely.
If the check engine light remains on, or
it flashes continuously , do not drive at
high speeds and consult an expert
repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
WARNING
If the check engine light turns on, do
not disconnect the battery leads.
If the battery leads are disconnected
and then reconnected, the engine
could be damaged and catch on
fire.
▼i-stop Warning Indication/
Warning Light (Amber)*
When the light is turned on
xA problem in the system may be
indicated under the following
conditions. Have your vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe light does not turn on when
the ignition is switched ON.
x(Except European model)
If the i-stop warning light (amber)
remains on while the engine is
running , the battery performance
may have decreased. Have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer).
When the light is flashing
The light continues to flash if the
system has a malfunction. Have your
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer).
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-53

Warning Sound is
Activated
▼Lights-On Reminder
If the ignition is switched OFF with the
exterior lights turned on and the
driver’s door is opened, a sound is
activated.
Operate the headlight switch to turn
off the exterior lights.
NOTE
xWhen the ignition is switched to
ACC, the “Ignition Not Switched
Off
(STOP) Warning Beep” (page 7-67)
overrides the lights-on reminder.
xA personalised function is available
to change the sound volume for the
lights-on reminder.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Seat Belt Warning Beep
Front seat
If the vehicle speed exceeds about 20
km/h (12 mph) with the driver or front
passenger's seat belt unfastened, a
warning beep sounds continuously. If
the seat belt remains unfastened, the
beep sound stops once and then
continues for about 90 seconds. The
beep stops after the driver or front
passenger's seat belt is fastened.
NOTE
xPlacing heavy items on the front
passenger seat may cause the front
passenger seat belt warning function
to operate depending on the weight
of the item.
xTo allow the front passenger seat
weight sensor to function properly,
do not place and sit on an additional
seat cushion on the front passenger
seat. The sensor may not function
properly because the additional seat
cushion could cause sensor
interference.
xWhen a small child sits on the front
passenger seat, it is possible that the
warning beep will not operate.
Rear seat
The warning beep only sounds if a seat
belt is unfastened after being fastened.
▼Ignition Not Switched Off (STOP)
Warning Beep
European models
If the driver's door is opened with the
ignition switched to ACC, a beep will
be heard 6 times in the cabin to notify
the driver that the ignition has not
been switched OFF (STOP). Under this
condition, the keyless entry system will
not operate, the vehicle cannot be
locked, and the battery voltage will be
depleted.
Except European models
If the driver's door is opened with the
ignition switched to ACC, a beep will
be heard continuously in the cabin to
notify the driver that the ignition has
not been switched OFF (STOP). Under
this condition, the keyless entry system
will not operate, the vehicle cannot be
locked, and the battery voltage will be
depleted.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-67

You can change the vehicle speed
setting at which the warning is
triggered.
▼120 km/h Warning Beep*
If the vehicle speed exceeds 120
km/h, a chime sounds for 5 seconds.
▼Blind Spot Monitoring (BSM)
Warn in g Beep*
The Blind Spot Monitoring (BSM)
warning beep operates when the
direction indicator lever is operated to
the side where the Blind Spot
Monitoring (BSM) warning light is
illuminated.
▼Front Cross Traffic Alert (FCTA)
Warn in g Beep*
The Front Cross Traffic Alert (FCTA)
warning beep is activated if there is a
possibility of collision with a vehicle
approaching from the front on the left
and right sides of the vehicle.
▼Rear Cross Traffic Alert (RCTA)
Warn in g Beep*
The Rear Cross Traffic Alert (RCTA)
warning beep is activated if there is a
possibility of collision with a vehicle
approaching from the rear on the left
and right sides of the vehicle.
▼Lane Departure Warning Sound*
While the system is operating, if the
system determines that the vehicle may
depart from the lane, it sounds a
warning sound.
NOTE
The volume of the Lane Departure
Warning System (LDWS) warning
sound can be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Mazda Radar Cruise Control
(MRCC) System Warnings*
The Mazda Radar Cruise Control
(MRCC) system warnings notify the
driver of system malfunctions and
cautions on use when required.
Check based on the beep sound.
Warning beep type Notification content
The beep sounds 1
time while the Mazda
Radar Cruise Control
(MRCC) is operatingThe vehicle speed is
slower than 25 km/h
(16 mph) and the
Mazda Radar Cruise
Control (MRCC) sys-
tem has been cancel-
led.
The beep sounds in-
termittently while the
Mazda Radar Cruse
Control (MRCC) is op-
erating.The distance between
your vehicle and the
vehicle ahead is too
close. Check the safety
of the surrounding
area and reduce vehi-
cle speed.
▼Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function) System
Warnings
*
The Mazda Radar Cruise Control with
Stop & Go function (MRCC with Stop
& Go function) system warnings notify
the driver of system malfunctions and
cautions on use when required.
Check based on the beep sound.
Warning beep type Notification content
The beep sounds 1
time while the Mazda
Radar Cruise Control
with Stop & Go func-
tion (MRCC with Stop
& Go function) is op-
eratingIf a malfunction occurs
in the system, make
sure that the Mazda
Radar Cruise Control
with Stop & Go func-
tion (MRCC with Stop
& Go function) has
been cancelled.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-71