2019 MAZDA MODEL CX-3 headlight bulb

Light Bulbs
With LED HeadlightsWith Halogen Headlights
Overhead lights (Front) /Map lights
Overhead lights (Rear)Overhead lights (Front) /Map lights
Headlights (High
beam)/Daytime running
lights
Headlights (Low beam)
Parking lights/Daytime
running lights Side turn signal lights
Fo g lights
Parking lights/Front
side-marker lights
Front side-marker lights
Front turn signal lights
Lugg age compartment light
License plate lights Reverse lights Taillights
Rear turn signal lights Rear side-marker lights
Brake lights/Taillights High-mount brake light
Some models.
Side turn signal lights
Headlights (High beam)
Headlights (Low beam)
Fog lights
Front turn signal lights
Maintenance and Care
Owner Maintenance
6-41
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

WA R N I N G
Never touch the glass portion of a halogen
bulb with your bare hands and always
wear eye protection when handling or
working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it will
explode and serious injuries could be
caused by the flying glass.
If the glass portion is touched with bare
hands, body oil could cause the bulb to
overheat and explode when lit.
Always keep halogen bulbs out of the reach
of children:
Playing with a halogen bulb is dangerous.
Serious injuries could be caused by
dropping a halogen bulb or breaking it
some other way.
CAUTION
When removing the lens or lamp unit using
a flathead screwdriver, make sure that the
flathead screwdriver does not contact the
interior terminal. If the flathead screwdriver
contacts the terminal, a short circuit may
occur.
NOTE
•To replace the bulb, contact an
Authorized Mazda Dealer.
•If the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
•Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.
▼Replacing Exterior Light Bulbs
Headlights (With
LED headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Headlights/Daytime running lights
(With halogen headlights)
High-beams bulbs/Daytime running
lights
1. Make sure the ignition is switched off, and the headligh t switch is off.
2. Lift the hood.
3. Disconnect the connector from the unit by pressing the tab on the connector
with your finger and pulling the
connector downward.

Maintenance and Care
Owner Maintenance
6-42
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

4. Turn the socket and bulb assembly toremove it. Carefully remove the bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.

5. Install the new bulb in the reverseorder of the removal procedure.
Low-beam bulbs
1. Make sure the ignition is switched off, and the headlight switch is off.
2. Lift the hood.
3. Disconnect the connector from the unit by pressing the tab on the connector
with your finger and pulling the
connector downward.

4. Turn the socket and bulb assembly toremove it. Carefully remove the bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.

5. Install the new bulb in the reverseorder of the removal procedure.
Parking lights/Daytime running lights/
Front side-marker lights (With LED
headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Maintenance and Care
Owner Maintenance
6-43
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

Parking lights/Front side-marker lights
(With halogen headlights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverseorder of the removal procedure.
Front turn signal lights
1. Make sure the ignition is switched off, and the headlight switch is off.
2. Turn the screw counterclockwise and remove it, and then partially peel back
the mudguard.

3. Turn the socket and bulb assemblycounterclockwise and remove it.
4. Disconnect the bulb from the socket.

5. Install the new bulb in the reverseorder of the removal procedure.
Fog lights
*, Side turn signal lights*,
Brake lights/Taillights (LED type), Rear
side-marker lights (LED type),Taillights
(LED type)*, High-mount brake light,
Reverse lights (LED type)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Maintenance and Care
Owner Maintenance
6-44*Some models.
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

Rear turn signal lights, Brake lights/
Taillights (Bulb type), Rear side-marker
lights (Bulb type)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the bolts counterclockwise and remove them.

3. Pull the unit rearward to remove it.
4. Turn the socket and bulb assemblycounterclockwise and remove it.
5. Disconnect the bulb from the socket.
Rear turn signal lights

Brake lights/Taillights

Rear side-marker lights

6. Install the new bulb in the reverse
order of the removal procedure.
Maintenance and Care
Owner Maintenance
6-45
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

Reverse lights (Bulb type)
1. Make sure the ignition is switched off,and the headlight switch is off.
2. Remove the cover.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.

5. Install the new bulb in the reverseorder of the removal procedure.
License plate lights
1. Make sure the ignition is switched off, and the headlight switch is off.
2. Remove the cover.

3. Turn the socket and bulb assemblycounterclockwise and remove it.

4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse
order of the removal procedure.
▼Replacing Interior Light Bulbs
Overhead lights (F
ront)/Map lights,
Overhead lights (Rear)
1. Wrap a small flathead screwdriver with
a soft cloth to prev ent damage to the
lens, and then remove the lens by
carefully prying on the edge of the lens
with the flathead screwdriver.
2. Disconnect the bulb by pulling it out.
Maintenance and Care
Owner Maintenance
6-46
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

▼We i g h t s
U.S.A. and Canada
Item We i g h t
2WD AW D
Automatic transaxle Manual transaxle
GVWR (Gross Vehicle Weight
Rating) 1,742 kg (3,840 lbs) 1,700 kg (3,748 lbs) 1,810 kg (3,990 lbs)
GAWR (Gross Axle
Weight Rating) Front 933 kg (2,057 lbs) 900 kg (1,984 lbs) 958 kg (2,112 lbs)
Rear 812 kg (1,790 lbs) 808 kg (1,781 lbs) 860 kg (1,896 lbs)

Mexico
Item
We i g h t
With moonroof Without moonroof
GVW (Gross Vehi-
cle Weight) Total
1,762 kg (3,885 lbs) 1,751 kg (3,860 lbs)
Front 924 kg (2,037 lbs) 918 kg (2,024 lbs)
Rear 838 kg (1,847 lbs) 833 kg (1,836 lbs)
GAW (Permissible
axle load) Front
939 kg (2,070 lbs) 933 kg (2,057 lbs)
Rear 887 kg (1,955 lbs) 887 kg (1,955 lbs)
▼Air Conditioner
The type of refrigerant used is indicated on a label attached t
o the inside of the engine com-
partment. Check the la bel before recharging the refrigerant. Re fer to Climate Control Sys-
tem on page 5-4.
Item Specification
Refrigerant Type HFC134a (R-134a)
▼Light Bulbs
Exterior light
Light bulb Category
Wattage UNECE*1 (SAE)
Headlights Halogen head-
lights
High beam/Daytime run-
ning lights
60
HB3 (9005)
Low beam 55H11 (H11)
LED headlights High beam
LED
*2― (―)
Low beam LED
*2― (―)
Specifications
Specifications
9-6
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14

Light bulbCategory
Wat tage UNECE*1 (SAE)
Parking lights/Front side-marker
lights With halogen headlights
5W5W (―)
Parking lights/Daytime running
lights With LED headlights
LED
*2― (―)
Front side-marker lights With LED headlights LED
*2― (―)
Front turn signal lights 27 ― (1156NA)
Fog lights
*LED*2― (―)
Side turn signal lights
*LED*2― (―)
High-mount brake light LED
*2― (―)
Rear turn signal lights 21 WY21W (7443NA)
Rear side-marker lights Bulb type 5 W5W (―)
LED type
LED
*2― (―)
Brake lights/Taillights Bulb type 21/5 W21/5W (7443)
LED type
LED
*2― (―)
Reverse lights Bulb type 16 W16W (921)
LED type
LED
*2― (―)
Taillights
*LED type LED*2― (―)
License plate lights 5 W5W (―)
*1 UNECE stands for United Nations Economic Commission for Europe.*2 LED is the abbreviation for Light Emitting Diode.
Interior light
Light bulb Category
Wa t t ag e UNECE*1
Overhead light (Front)/Map lights 8 ―
Overhead light (Rear) 10―
Luggage compartment light 5―
*1 UNECE stands for United Nations Economic Commission for Europe.
▼Tires
NOTE
The tires have been optimally matched with the chassis of your vehicle.
When replacing tires, Mazda recommends that you replace tires of the same type originally
fitted to your vehicle. For details, contact an Authorized Mazda Dealer.
Check the tire pressure label for tire size and inflation press
ure.
Refer to Tire Inflation Pressure on page 6-36.
Specifications
Specifications
*Some models.9-7
CX-3_8GR7-EA-18B_Edition1 2017-12-20 16:18:14