2019 MAZDA MODEL 2 warning light
[x] Cancel search: warning lightPage 255 of 759
NOTE
xThe BSM will operate when all of the following conditions are met:
xThe ignition is switched ON.
xThe BSM OFF switch is pressed and the BSM OFF switch indicator light is turned off.
xThe vehicle speed is about 30 km/h (19 mph) or faster.
xThe BSM will not operate under the following circumstances.
xThe vehicle speed falls below about 25 km/h (15 mph) even though the BSM OFF switch
indicator light is turned off.
xThe shift lever (manual transaxle)/selector lever (automatic transaxle) is shifted to R
position and the vehicle is reversing.
xThe turning radius is small (making a sharp turn, turning at intersections).
xIn the following cases, the BSM OFF indicator light turns on and operation of the system
is stopped. If the BSM OFF indicator light remains illuminated, have the vehicle inspected
at an expert repairer (we recommend an Authorised Mazda Repairer) as soon as possible.
xSome problem with the system including the BSM warning indicator lights is detected.
xA large deviation in the installation position of a radar sensor (rear) on the vehicle has
occurred.
xThere is a large accumulation of snow or ice on the rear bumper near a radar sensor
(rear). Remove any snow, ice or mud on the rear bumper.
xDriving on snow-covered roads for long periods.
xThe temperature near the radar sensors (rear) becomes extremely hot due to driving for
long periods on slopes during the summer.
xThe battery voltage has decreased.
xUnder the following conditions, the radar sensors (rear) cannot detect target objects or it
may be difficult to detect them.
xA vehicle is in the detection area at the rear in an adjacent driving lane but it does not
approach. The BSM determines the condition based on radar detection data.
xA vehicle is travelling alongside your vehicle at nearly the same speed for an extended
period of time.
xVehicles approaching in the opposite direction.
xA vehicle in an adjacent driving lane is attempting to pass your vehicle.
xA vehicle is in an adjacent lane on a road with extremely wide driving lanes. The
detection area of the radar sensors (rear) is set at the road width of expressways.
xIn the following case, the flashing of the BSM warning indicator light, and the activation
of the warning sound and the warning screen indicator display may not occur or they may
be delayed.
xA vehicle makes a lane change from a driving lane 2 lanes over to an adjacent lane.
xDriving on steep slopes.
xCrossing the summit of a hill or mountain pass.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 256 of 759
xWhen there is a difference in the height between your driving lane and the adjacent
lane.
xDirectly after the BSM system becomes operable by changing the setting.
xIf the road width is extremely narrow, vehicles 2 lanes over may be detected. The detection
area of the radar sensors (rear) is set according to the road width of expressways.
xThe BSM warning indicator light may turn on and the vehicle detection screen may be
displayed in the display in reaction to stationary objects (guardrails, tunnels, sidewalls,
and parked vehicles) on the road or the roadside.
Objects such as guardrails and concrete walls
running alongside the vehicle.Places where the width between guardrails or
walls on each side of the vehicle narrows.
The walls at the entrance and exits of tunnels,
turnouts.
xA BSM warning indicator light may flash or the warning beep and the warning screen
indicator display may be activated several times when making a turn at a city
intersection.
xTurn off the BSM while pulling a trailer or while an accessory such as a bicycle carrier is
installed to the rear of the vehicle. Otherwise, the radar’s radio waves will be blocked
causing the system to not operate normally.
xIn the following cases, it may be difficult to view the illumination/flashing of the BSM
warning indicator lights equipped on the door mirrors.
xSnow or ice is adhering to the door mirrors.
xThe front door glass is fogged or covered in snow, frost or dirt.
xThe system switches to the Rear Cross Traffic Alert function when the shift lever (manual
transaxle) or the selector lever (automatic transaxle) is shifted to the reverse (R) position.
Refer to Rear Cross Traffic Alert (RCTA) on page 4-130.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 272 of 759
NOTE
xIn the following cases, the Blind Spot Monitoring (BSM) warning indication/warning light
turns on and operation of the system is stopped. If the Blind Spot Monitoring (BSM)
warning indication/warning light remains illuminated, have the vehicle inspected at an
Authorised Mazda Dealer as soon as possible.
xSome problem with the system including the Blind Spot Monitoring (BSM) warning
indicator lights has occurred.
xA large deviation in the installation position of a radar sensor (rear) on the vehicle has
occurred.
xThere is a large accumulation of snow or ice on the rear bumper near a radar sensor
(rear).
xDriving on snow-covered roads for long periods.
xThe temperature near the radar sensors becomes extremely hot due to driving for long
periods on slopes during the summer.
xThe battery voltage has decreased.
xUnder the following conditions, the radar sensors (rear) cannot detect target objects or it
may be difficult to detect them.
xThe vehicle speed when reversing is about 10 km/h (6 mph) or faster.
xThe radar sensor (rear) detection area is obstructed by a nearby wall or parked vehicle.
(Reverse the vehicle to a position where the radar sensor detection area is no longer
obstructed.)
Your vehicle
xA vehicle is approaching directly from the rear of your vehicle.
Your vehicle
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 273 of 759
xThe vehicle is parked at an angle.
Your vehicle
x(With Blind Spot Monitoring (BSM) OFF switch)
Directly after pressing the Blind Spot Monitoring (BSM) OFF switch and the system
becomes operable.
(Without Blind Spot Monitoring (BSM) OFF switch)
Directly after the Blind Spot Monitoring (BSM) system becomes operable using the
personalisation feature.
xIn the following cases, it may be difficult to view the illumination/flashing of the Blind
Spot Monitoring (BSM) warning indicator lights equipped on the door mirrors.
xSnow or ice adheres to the door mirrors.
xThe front door glass is fogged or covered in snow, frost or dirt.
xTurn off the RCTA system while pulling a trailer or while an accessory such as a bicycle
carrier is installed to the rear of the vehicle. Otherwise, the radio waves emitted by the
radar will be blocked causing the system to not operate normally.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 276 of 759
xThe following are not detected as physical objects.
xVehicles approaching in the opposite direction
xPedestrians
xStationary objects (stopped vehicles, obstructions)
xIf a vehicle ahead is travelling at an extremely low speed, the system may not detect it
correctly.
xDuring headway control travel, do not set the system on two-wheeled vehicles such as
motorcycles and bicycles.
xDo not use the MRCC system under conditions in which the close proximity warnings are
frequently activated.
xDuring headway control travel, the system accelerates and decelerates your vehicle in
conjunction with the speed of the vehicle ahead. However, if it is necessary to accelerate
for a lane change or if the vehicle ahead brakes suddenly causing you to close in on the
vehicle rapidly, accelerate using the accelerator pedal or decelerate using the brake
pedal depending on the conditions.
xWhile the MRCC system is in use, it does not cancel even if the selector lever (automatic
transaxle)/shift lever (manual transaxle) is operated and any intended engine braking will
not occur. If deceleration is required, lower the vehicle speed setting or depress the brake
pedal.
xThe brake lights are illuminated while the MRCC automatic braking is operating,
however, they may not be illuminated while the vehicle is on a down slope at the set
vehicle speed or travelling at a constant speed and following a vehicle ahead.
xThe MRCC warning light (amber) illuminates when the system has a malfunction.
Refer to Warning Lights on page 4-39.
xThe headway control operation can be cancelled and the system can be switched to only
cruise control.
Refer to Cruise Control Function on page 4-143.
▼ 0 D ] G D 5 D G D U & U X L V H & R Q W U R O 0 5 & & ' L V S O D \ , Q G L F D W L R Q
7 K H V H W W L Q J V W D W X V D Q G R S H U D W L R Q F R Q G L W L R Q V R I W K H 0 5 & & V \ V W H P D U H L Q G L F D W H G L Q W K H D F W L Y H
G U L Y L Q J G L V S O D \
Vehicle ahead display
MRCC Distance
between vehicle
display
MRCC Set vehicle speed
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 290 of 759
xIf you take your hands off the steering wheel (not holding the steering wheel), the warning
sound is activated and an alert is indicated in the active driving display or the warning
light turns on in the instrument cluster.
With Active Driving Display Without Active Driving Display
If the steering wheel is held lightly, or depending on the road conditions, the system may
detect that you have released the steering wheel (not holding the steering wheel) even if
you are holding it, and display a message in the active driving display.
xThe timing at which the lane departure warning is activated and the steering wheel
operation assist is performed varies.
xThe following settings for the LAS&LDWS can be changed. Refer to Personalisation
Features on page 9-15.
xSteering operation assist operational/non-operational
xCancel sensitivity (likelihood of steering assist)
9 H K L F O H O D Q H O L Q H G L V S O D \
: K H Q W K H / $ 6 / ' : 6 G H W H F W V Z K L W H \ H O O R Z O L Q H V R Q E R W K W K H O H I W D Q G U L J K W V L G H V D Q G
E H F R P H V R S H U D W L R Q D O W K H Y H K L F O H O D Q H O L Q H V D U H L Q G L F D W H G L Q W K H D F W L Y H G U L Y L Q J G L V S O D \ R U W K H
/ $ 6 / ' : 6 L Q G L F D W R U O L J K W W X U Q V R Q L Q W K H L Q V W U X P H Q W F O X V W H U
With Active Driving Display Without Active Driving Display
$ X W R F D Q F H O
, Q W K H I R O O R Z L Q J F D V H V W K H / $ 6 / ' : 6 L V D X W R P D W L F D O O \ F D Q F H O O H G D Q G W K H Y H K L F O H O D Q H
O L Q H V V W D Q G E \ D U H L Q G L F D W H G L Q W K H D F W L Y H G U L Y L Q J G L V S O D \ , Q D G G L W L R Q Z K H Q W K H
/ $ 6 / ' : 6 E H F R P H V R S H U D W L R Q D O W K H V \ V W H P W X U Q V E D F N R Q D X W R P D W L F D O O \ D Q G W K H Y H K L F O H
O D Q H O L Q H V R S H U D W L R Q D O D U H L Q G L F D W H G L Q W K H D F W L Y H G U L Y L Q J G L V S O D \
x 7 K H W H P S H U D W X U H L Q V L G H W K H F D P H U D L V K L J K R U O R Z
x 7 K H Z L Q G V F U H H Q D U R X Q G W K H F D P H U D L V I R J J \
x 7 K H Z L Q G V F U H H Q D U R X Q G W K H F D P H U D L V E O R F N H G E \ D Q R E V W U X F W L R Q F D X V L Q J S R R U I R U Z D U G
Y L V L E L O L W \
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 294 of 759
▼ 6 \ V W H P & D Q F H O O L Q J
: K H Q W K H / D Q H N H H S $ V V L V W 6 \ V W H P / $ 6
/ D Q H ' H S D U W X U H : D U Q L Q J 6 \ V W H P
/ ' : 6 L V W X U Q H G R I I S U H V V W K H / D Q H N H H S
$ V V L V W 6 \ V W H P / $ 6 / D Q H ' H S D U W X U H
: D U Q L Q J 6 \ V W H P / ' : 6 2 ) ) V Z L W F K
7 K H / D Q H N H H S $ V V L V W 6 \ V W H P / $ 6
/ D Q H ' H S D U W X U H : D U Q L Q J 6 \ V W H P / ' : 6
2 ) ) V Z L W F K L Q G L F D W R U O L J K W W X U Q V R Q
NOTE
xIn the following cases, the Lane-keep
Assist System (LAS) & Lane Departure
Warning System (LDWS) is cancelled
automatically and the Lane-keep Assist
System (LAS) & Lane Departure
Warning System (LDWS) OFF indicator
light turns on. Have your vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThere is a malfunction in the power
steering.
xThere is a malfunction in the DSC.
xThere is a malfunction in the Forward
Sensing Camera (FSC).
xWhen the ignition is switched OFF, the
system status before it was turned off is
maintained. For example, if the ignition
is switched OFF with the lane-keep
system operable, the system will be
operable when the ignition is switched
ON the next time.
: K H Q W K H / D Q H N H H S $ V V L V W 6 \ V W H P / $ 6
/ D Q H ' H S D U W X U H : D U Q L Q J 6 \ V W H P
/ ' : 6 L V F D Q F H O O H G W K H Y H K L F O H O D Q H
O L Q H V D U H Q R O R Q J H U L Q G L F D W H G L Q W K H D F W L Y H
G U L Y L Q J G L V S O D \
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 295 of 759
▼ / D Q H ' H S D U W X U H : D U Q L Q J
, I W K H V \ V W H P G H W H U P L Q H V W K D W W K H Y H K L F O H P D \ G H Y L D W H I U R P L W V O D Q H W K H O D Q H G H S D U W X U H
Z D U Q L Q J E H H S V R X Q G U X P E O H V R X Q G
R U V W H H U L Q J Z K H H O Y L E U D W L R Q L V D F W L Y D W H G D Q G W K H
G L U H F W L R Q L Q Z K L F K W K H V \ V W H P G H W H U P L Q H V W K D W W K H Y H K L F O H P D \ G H Y L D W H L V L Q G L F D W H G L Q W K H
D F W L Y H G U L Y L Q J G L V S O D \
, I W K H V \ V W H P G H W H U P L Q H V W K D W W K H Y H K L F O H P D \ G H Y L D W H I U R P L W V O D Q H W K H F R O R X U R I W K H O D Q H
O L Q H R Q W K H V L G H E H L Q J G H W H F W H G E \ W K H V \ V W H P F K D Q J H V I U R P Z K L W H W R D P E H U D Q G I O D V K H V
Warning light (Flashes) Active Driving Display
NOTE
xIf you have set the lane departure warning sound to the beep sound/rumble sound*1
setting, the warning sound may not be heard depending on the surrounding noise
conditions.
xIf you have set the lane departure warning system to the steering wheel vibrations setting,
the vibration may not be felt depending on the road surface conditions.
xWhen the setting for the steering operation assist is changed to operational, the warnings
can be set to activate/not activate. (When the setting for the steering operation assist is
changed to non-operational, the warnings cannot be set to not activate.)
Refer to Setting Change (Personalisation Features) on page 9-15.
xThe LAS & LDWS can be changed to the following settings regardless of whether the
steering operation assist has been set to operational/non-operational. Always check the
setting status when driving the vehicle and make setting changes if necessary.
Refer to Setting Change (Personalisation Features) on page 9-15.
xSteering wheel vibration: Strong/weak
xWarning sound volume
xTypes of warnings (steering wheel vibration/beep sound/rumble sound*1)
*1 A rumble strip is a series of grooves in the road pavement surface positioned at specific
intervals, and when the vehicle passes over it a vibration and rumble sound is produced
which alerts the driver that the vehicle is departing from the lane.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (