2019 KIA SPORTAGE sensor

9
DRIVER'S PANEL
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS *IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
For more information on the BSW / RCCW, refer to your Owner’s Manual.
Blind-Spot Collision Warning (BSW)†5
The BSW system uses radar sensors to help alert the driver before changing
lanes The light on the BSW button A will illuminate when turned ON The outside
rearview mirror warning lights will also illuminate for 3 seconds
The system will become active when the vehicle is traveling more than 20 mph
and will alert the driver if another vehicle is detected by the radar sensor
REMINDERS:
•When the BSW is ON and the vehicle power is cycled to OFF then ON again, the BSW system returns to ON
•
The RCCW feature can be turned OFF/ON in User Settings from the LCD Instrument Cluster modes
•When vehicle power is cycled, the RCCW will remain in the previous state
Blind-Spot Collision Warning w/ RCCW Video
To view a video on your mobile device, snap this QR Code or visit the listed website
Refer to page 2 for more information
www.youtube.com/KiaFeatureVideosRear Cross-Traffic Collision Warning (RCCW)*
If the RCCW system sensors detect approaching vehicles from the left or right
side C, the system will sound an audible alert, the warning indicators on the
outside rearview mirror will illuminate and a message will appear on the LCD
screen RCCW is designed to operate under these following conditions:
•When the gear shift is in Reverse
•When the vehicle moves in reverse from a parked position
•When the vehicle is moving less than 6 mph
QR CODE
Blind-Spot Collision Warning* / Lane Change Assist (LCA)*
1st-stage alert: When another vehicle is detected within the BSW System boundary B, or when a vehicle detected with the LCA boundary, a yellow indicator will
illuminate on the outside rearview mirrors
2nd-stage alert: When 1st-stage alert is on and the driver activates a turn signal,
a flashing yellow indicator will illuminate on the outside rearview mirrors and the
system will sound an alert
B
A
C

DRIVER'S PANEL
10SPORTAGE FEATURES & FUNCTIONS GUIDE*IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
Electronic Stability Control (ESC)†6
The ESC system is designed to help stabilize the vehicle
during cornering maneuvers It is a good idea to keep
the ESC turned ON for daily driving whenever possible
Press ESC button B to turn ESC OFF/ON
REMINDERS:
•
ESC is turned ON by default at vehicle start-up When ignition is cycled, ESC will turn ON again
•
The ESC Indicator Light in the instrument cluster will illuminate whenever the ESC is in operation
Lane Departure Warning (LDW)*†5
AC
B
Lane Departure Warning Video
To view a video on your mobile device, snap this QR Code or visit the listed website
Refer to page 2 for more information
www.youtube.com/KiaFeatureVideos
QR CODE
With the Engine Start /Stop button in the ON position, press the LDW
button C to turn system ON The instrument cluster indicator
will illuminate white It will remain white when vehicle is traveling less
than 40 mph and the system does not detect the lane markers When
system detects the lane markers, the LDW icon will illuminate green
If the LDW detects that you are moving outside of your lane, the
system may issue a warning on the LCD screen and an alert may
sound, under these conditions:
• The vehicle exceeds approximately 40 mph
• The LDW system recognizes the lane the vehicle is traveling in
and the vehicle is not between the lane markers
If the LDW button is ON and ignition is cycled, the system will turn
ON again If the LDW button is OFF, the system remains OFF
REMINDER: LDW will not issue a warning if the turn signal or hazard lights are activated
Lane Departur e
Lane Departure
Lane Departure
Lane Departure
Lane Departure
Lane Departure
Lane Departure
Lane Departure
The Lane Departure Warning (LDW) is not a substitute for safe and proper driving. Always drive safely and use caution. LDW may not always alert the driver if the vehicle is driven outside of its lane.
(Buttons located on left of Steering Wheel)
Instrument Cluster Control
With parking lights/headlights ON, toggle switch A up (+) or down (-) to adjust the brightness of the
instrument panel illumination
REMINDER: The Instrument Cluster Control does not adjust brightness on the audio/navigation system* screens; see the display settings in the Setup menu to adjust the brightness on the screen
When the LDW sensor does not detect the the indicator will not illuminate
When the LDW sensor detects the vehicle moving outside of the lane the vehicle’s traveling in, a yellow indicator will illuminate either on the left or right lane (shown in both images above)
When the LDW sensor detects the lane traveling in, both indicators are illuminated
Lane Departure
Lane Departure
Lane Departure
Lane Departure
For more information on Electronic Stability Control (ESC) and its specific features and operations, please refer to your Owner’s Manual.

36SPORTAGE FEATURES & FUNCTIONS GUIDE
OTHER KEY FEATURES
*IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
HomeLink® with Auto-Dimming
Rearview Mirror*†1 0
A HomeLink® button
B HomeLink® button
C Indicator light
D HomeLink® button
E Glare detection sensor
F Automatic dimming ON
G Automatic dimming OFF
ABCDEFG
REMINDER: Mirror indicator light C will illuminate when automatic dimming is ON
The Auto-Dimming Rearview Mirror* is designed to reduce glare
from a vehicle’s headlights located in the rear and also connect up
to three electronic transmitters into one location
•
To turn automatic dimming ON, press button F
•
To turn automatic dimming OFF, press button G
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515.
HomeLink® Setup - How to Sync Transmitter
If programming for the first time, begin with Step 1
(repeating this step will delete all information)
To program non-rolling and rolling code garage
door openers and other devices:
1
Press and hold the left A and center D buttons
simultaneously until the indicator light C begins
to flash (to reprogram buttons, skip this step)
2 Press and hold the desired button A, B or D
and hold the button on the transmitter while it
is approximately 1 to 3 inches away from the
mirror The HomeLink® Indicator light C will
flash rapidly once the frequency signal has been
successfully programmed
To finish programming rolling code garage door
openers, complete these steps:
3 Locate the “learn” or “smart” button on the garage door’s motor head unit
Press and release the button and complete Step 4 within 30 seconds
4 Firmly press and release the programmed HomeLink® button up to three times
• You can reprogram a single HomeLink® button by repeating Step 2• Erasing programmed buttons will delete all trained transmitters
QUICK TIP
Operating HomeLink®:
Press one of the programmed HomeLink® buttons
Erasing programmed buttons:
Press and hold the left A and center D buttons simultaneously for approximately
20 seconds, and then release both buttons within 30 seconds
HomeLink Setup Video
To view a video on your mobile device, snap this QR Code or visit the listed website
Refer to page 2 for more information
www.youtube.com/KiaFeatureVideos
QR CODE