2019 KIA NIRO bulb

Features of your vehicle
120
4
If an indicator stays on and does not
flash or if it flashes abnormally, one of
the turn signal bulbs may be burned
out and will require replacement.
✽ ✽
NOTICE
If an indicator flash is abnormally
quick or slow, a bulb may be burned
out or have a poor electrical connec-
tion in the circuit.
Check headlight
This warning message illuminates if
there is a malfunction (burned-out
bulb except LED lamp or circuit mal-
function) with the headlamp. In this
case, have your vehicle inspected by
an authorized Kia dealer.
✽ ✽NOTICE
• When replacing the bulb, use the
same wattage bulb.
For more information, refer to
“BULB WATTAGE” in chapter 9.
• If a different wattage bulb is installed on the vehicle, this warn-
ing message is not displayed.
Front fog light (if equipped)
Fog lights are designed to provide
improved visibility when visibility is
poor due to fog, rain or snow, etc. The
fog lights will turn on when the fog light
switch (1) is turned to the on position
after the headlight is turned on.
To turn off the fog lights, turn the fog
light switch (1) to the ON position
again.
When in operation, the fog lights
consume large amounts of vehicle
electrical power. Only use the fog
lights when visibility is poor.
OJFA055274ODE046458N

Tire terminology and definitions . . . . . . . . . . . . . . . . 8-50
All season tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-53
Summer tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-53
Snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-\
53
Tire chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-54\
Radial-ply tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-54
Low aspect ratio tire . . . . . . . . . . . . . . . . . . . . . . . . . . 8-55
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
8-56
Inner panel fuse replacement . . . . . . . . . . . . . . . . . . . 8-57
Engine compartment fuse replacement. . . . . . . . . . . 8-59
Fuse/relay panel description. . . . . . . . . . . . . . . . . . . . 8-62
Light bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-84
Bulb replacement precaution . . . . . . . . . . . . . . . . . . 8-84
Light bulb position (Front). . . . . . . . . . . . . . . . . . . . . 8-85
Light bulb position (Rear) . . . . . . . . . . . . . . . . . . . . . 8-86
Light bulb position (Side) . . . . . . . . . . . . . . . . . . . . . . 8-87
Headlamp (HID type) bulb replacement . . . . . . . . . 8-87
Headlamp (LED type) replacement. . . . . . . . . . . . . . 8-88
Headlamp (High/Low beam) bulb replacement . . . 8-88
Front turn signal lamp bulb replacement . . . . . . . . 8-89
Fog lamp/DRL bulb replacement . . . . . . . . . . . . . . . 8-90
Stop and tail lamp bulb replacement . . . . . . . . . . . . 8-90
Tail lamp (inside) bulb replacement . . . . . . . . . . . . . 8-92
Stop and tail lamp (LED type) bulb replacement . . 8-93
Back-up lamp bulb replacement . . . . . . . . . . . . . . . . 8-93
High mounted stop lamp bulb replacement . . . . . . . 8-93
License plate lamp bulb replacement . . . . . . . . . . . . 8-94
Side repeater lamp (LED type) bulb replacement . . 8-94
Map lamp (Bulb type) bulb replacement . . . . . . . . . 8-95
Map lamp (LED type) bulb replacement . . . . . . . . . 8-95
Vanity mirror lamp bulb replacement . . . . . . . . . . . 8-95
Room lamp (Bulb type) bulb replacement . . . . . . . . 8-96
Room lamp (LED type) bulb replacement . . . . . . . . 8-97
Liftgate room lamp bulb replacement . . . . . . . . . . . 8-97
Appearance care . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-98
Exterior care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-98
Interior care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-103
Emission control system . . . . . . . . . . . . . . . . . . . 8-106
Crankcase emission control system . . . . . . . . . . . . . 8-106
Evaporative emission control (Including ORVR :
Onboard Refueling Vapor Recovery) system . . . . 8-106
Exhaust emission control system . . . . . . . . . . . . . . . 8-107
California perchlorate notice . . . . . . . . . . . . . . . 8-109
8

Maintenance
58
8
3. Pull the suspected fuse straight
out. Use the removal tool provided
on the engine compartment fuse
panel cover.
4. Check the removed fuse; replace it if it is blown.
Spare fuses are provided in theengine compartment fuse panel.
5. Push in a new fuse of the same rating, and make sure it fits tightly
in the clips.
If it fits loosely, consult an authorized
Kia dealer.
If you do not have a spare, use a fuse of the same rating from a circuityou may not need for operating thevehicle, such as the power outletfuse.
If the head lamp, turn signal lamp,
stop signal lamp, fog lamp, DRL, tail
lamp, HMSL do not work and the
fuses are OK, check the fuse panel
in the engine compartment. If a fuse
is blown, it must be replaced.
✽ ✽ NOTICE
If the headlamp, fog lamp, turn sig-
nal lamp, or tail lamp malfunction
even without any problem to the
lamps, have the vehicle checked by
an authorized Kia dealer for assis-
tance.
ODE076020
CAUTION
Do not input any other objects
except fuses or relays intofuse/relay terminals, such as adriver or wiring. It may causecontact failure and systemmalfunction.
Do not plug in screwdrivers or aftermarket wiring into the ter-minal originally designed forfuse and relays only. The elec-trical system and wiring of thevehicle interior may be dam-aged or burned due to contactfailure.
If you directly connect the wire on the taillight or replacethe bulb which is over the reg-ulated capacity to install trail-ers, etc., the inner junctionblock can get burned.

Maintenance
84
8
LIGHT BULBS
Bulb replacement precaution
Please keep extra bulbs on hand
with appropriate wattage ratings in
case of emergencies.
Refer to “Bulb Wattage” in chapter 9.
When changing lamps, first turn off
the engine at a safe place, firmly
apply the parking brake and detach
the battery’s negative (-) terminal.
Use only bulbs of the specified
wattage.✽ ✽ NOTICE
• If the light bulb or lamp connector
is removed while the lamp is still
on, the fuse box's electronic sys-
tem may log it as a malfunction.
Therefore, a lamp malfunction
incident may be recorded as a
Diagnostic Trouble Code (DTC) in
the fuse box.
• It is normal for an operating lamp to flicker momentarily. This is due
to a stabilization function of the
vehicle’s electronic control device.
If the lamp lights up normally
after momentarily blinking, then
it is functioning as normal.
However, if the lamp continues to
flicker several times or turns off
completely, there may be an error
in the vehicle’s electronic control
device. Please have the vehicle
checked by an authorized Kia
dealer immediately.
✽ ✽ NOTICE
We recommend that the headlight
aiming be adjusted by an authorized
Kia dealer after an accident or after
the headlight assembly is reinstalled.
WARNING- Working on
the lights
Prior to working on the light,
firmly apply the parking brake,
ensure that the engine
start/stop button is in OFF posi-
tion and turn off the lights to
avoid sudden movement of the
vehicle and burning your fingers
or receiving an electric shock.
CAUTION -Light replace-
ment
Be sure to replace the burned- out bulb with one of the samewattage rating. Otherwise, itmay cause damage to the fuseor electric wiring system.
CAUTION -Headlamp
Lens
To prevent damage, do notclean the headlamp lens withchemical solvents or strongdetergents.

885
Maintenance
✽ ✽NOTICE
After driving in heavy rain or wash-
ing, headlamp and taillamp lenses
could appear frosty. This condition is
caused by the temperature differ-
ence between the lamp inside and
outside. This is similar to the con-
densation on your windows inside
your vehicle during the rain and
doesn’t indicate a problem with your
vehicle. If the water leaks into the
lamp bulb circuitry, we recommend
that you have the vehicle checked by
an authorized Kia dealer.
If you don’t have the necessary tools,
the correct bulbs and the expertise,
consult an authorized Kia dealer. In
many cases, it is difficult to replace
vehicle light bulbs because other
parts of the vehicle must be removed
before you can get to the bulb. This is
especially true if you have to remove
the headlamp assembly to get to the
bulb(s).
Removing/installing the headlamp
assembly can result in damage to
the vehicle.
If non-genuine parts or substandard
bulbs are used, it may lead to blow-
ing a fuse or other wiring damages.
Do not install extra lamps or LEDs to
the vehicle. If additional lights are
installed, it may lead to lamp mal-
functions and flickering. Additionally,
the fuse box and other writing may
be damaged.Light bulb position (Front)
■Head lamp - Type B
■Head lamp - Type A
ODEP077029N■Fog lamp
ODE076029N
ODEP077030N

Maintenance
86
8
(1) Headlamp (Low/High) (Bulb type)
(2) Front turn signal lamp (Bulb type)
(3) Position lamp (LED type)
(4) Side marker (Bulb type)
(5) Headlamp (Low/High) (LED type)
(6) Headlamp (Low) (LED type)
(7) Front turn signal lamp/Position
lamp (LED type)
(8) Side marker (LED type)
(9) Day time running lamp (LED type)
(10) Front fog lamp (Bulb type)Light bulb position (Rear)
(1) Stop/tail lamp (Bulb type)
(2) Tail lamp (Bulb type)
(3) Rear turn signal lamp (Bulb type)
(4) Side marker (Bulb type)
(5) Side marker (LED type)
(6) Stop/tail lamp (LED type)
(7) Back up lamp (Bulb type)
(8) License plate lamp (Bulb type)
(9) High mounted stop lamp (LED type)
■Rear combination lamp
- Type B
■Rear combination lamp
- Type A
ODEP077032N■Back up lamp
ODE076031N
ODEP077033N
■High mounted stop lamp
■License plate lamp
ODE076056L
ODEP077055N

887
Maintenance
Light bulb position (Side)
(1) Side repeater lamp (LED type)
Headlamp (HID type) bulb
replacement
If the light bulb does not operate,
have the vehicle checked by an
authorized Kia dealer.
✽ ✽NOTICE
If your vehicle is equipped with
High Intensity Discharge (HID)
headlamps, these headlamps contain
mercury. If you need to have your
vehicle disposed, you should remove
the HID headlamps before disposal.
The removed HID headlamps
should be recycled, re-used or dis-
posed as hazardous waste.
✽ ✽NOTICE
HID lamps have superior perform-
ance vs. halogen bulbs. HID lamps
are estimated by the manufacturer to
last twice as long or longer than halo-
gen bulbs depending on their fre-
quency of use. They will probably
require replacement at some point in
the life of the vehicle. Cycling the
headlamps on and off more than typ-
ical use will shorten HID lamps life.
HID lamps do not fail in the same
manner as halogen incandescent
lamps. If a headlamp goes out after a
period of operation but will immedi-
ately relight when the headlamp
switch is cycled it is likely the HID
lamp needs to be replaced. HID
lamping components are more com-
plex than conventional halogen bulbs
thus have higher replacement cost.
ODE076034
WARNING- HID
Headlamp (if equipped)
Do not attempt to replace or
inspect the HID headlamp
(XENON bulb) due to risk of
electric shock. If the light bulb
does not operate, have your
vehicle checked by an author-
ized Kia dealer.

Maintenance
88
8
Headlamp (LED type) replace-
ment
If the Low/High beam lamp (1), Low
beam lamp (2), Front turn signal
lamp/Position lamp(3), or side mark-
er (4) does not operate, have the
vehicle checked by an authorized Kia
dealer.
The LED lamps cannot be replaced
as a single component because they
are part of an integrated unit. The
LED lamps have to be replaced with
the unit.
A skilled technician should check or
repair the head lamp (LED), for it
may damage related parts of the
vehicle.
Headlamp (High/Low beam)
bulb replacement
1. Open the hood.
2. Remove the headlamp bulb cover
by turning it counterclockwise.
3. Disconnect the headlamp bulb socket-connector.
4. Remove the bulb-socket from the headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp
assembly. 5. Install a new bulb-socket assem-
bly in the headlamp assembly by
aligning the tabs on the bulb-sock-
et with the slots in the headlamp
assembly. Push the bulb-socket
into the headlamp assembly and
turn the bulb-socket clockwise.
6. Install the headlamp bulb cover by turning it clockwise.
ODE076035ODEP077073N