2019 INFINITI QX80 automatic transmission

5
LIMITATION OF WARRANTIES AND
OTHER WARRANTY TERMS AND
STATE LAW RIGHTS EXTRA EXPENSES
- LIMITATIONS OF DAMAGES THIS
WARRANTY DOES NOT COVER
INCIDENTAL OR CONSEQUENTIAL
DAMAGES SUCH AS LOSS OF THE USE
OF THE VEHICLE, INCONVENIENCE OR
COMMERCIAL LOSS.
ANY IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE SHALL BE
LIMITED TO THE DURATION OF THIS
WRITTEN WARRANTY.
Some states do not allow the exclusion or
limitation of incidental or consequential
damages or limitations on how long an
implied warranty lasts, so the above
limitations or exclusions may not apply to
you. This warranty gives you specific legal
rights, and you may also have other rights
which vary from state to state.
Infiniti does not authorize any person to
create for it any other warranty, obligation
or liability in connection with this vehicle.
THE WARRANTY BEGINS
The warranty period begins on the date the
vehicle is delivered to the first retail buyer or
put into service, whichever is earlier.
FOR HOW LONG AND WHAT IS
COVERED
BASIC COVERAGE
•The basic coverage period is 48 months or
60,000 miles, whichever comes first.
•The warranty covers any repairs needed to
correct defects in materials or workmanship
of all parts and components of each new
Infiniti vehicle supplied by Infiniti subject
to the exclusions listed under the heading
”WHAT IS NOT COVERED” or, if the part is
covered by one of the separate coverages
described in the following sections of this
warranty, that specific coverage applies
instead of the basic coverage.
POWERTRAIN COVERAGE
•The Powertrain coverage period is 72
months or 70,000 miles, whichever comes
first.
•This warranty covers any repairs needed to
correct defects in material or workmanship.
•Powertrain coverage includes components
listed below, under the headings Engine,
Transmission and Transaxle, Drivetrain, and
Restraint System, supplied by Infiniti, subject
to the exclusions listed under the heading
“WHAT IS NOT COVERED.” ENGINE - Cylinder heads and block and
all internal parts, rocker covers and oil pan,
valve train and front cover, timing chain and
tensioner, oil pump, water pump and fuel
pump, fuel injectors, intake and exhaust
manifolds, flywheel, seals and gaskets. TRANSMISSION AND TRANSAXLE
- Case and all internal parts, torque
converter and converter housing,
automatic transmission control module,
transfer case and all internal parts, seals
and gaskets, clutch cover and housing,
A/T cooler, and electronic transmission
controls.
DRIVETRAIN - Drive shafts, final drive
housing and all internal parts, propeller
shafts, universal joints, bearings, seals and
gaskets.
RESTRAINT SYSTEM - Air bags and
related electronic control systems.
CORROSION COVERAGE (PERFORATION
FROM CORROSION)
Any body sheet metal panel supplied by Infiniti
found to have developed perforation (rust-
through) due to corrosion in normal use is
covered for 84 months, regardless of mileage,
except for those items listed under “WHAT IS
NOT COVERED.” No additional rust proofing
applications are required. Perforation is a
condition in which any body sheet metal panel
has corroded from one surface to another.
TOWING COVERAGE
If your vehicle is inoperative due to the failure
of a warranted part during any of the New
Vehicle Limited warranties, including Emission
and Seat belt warranties, towing service to the
nearest authorized Infiniti retailer is covered.
(Continued on next page)
2019 NEW VEHICLE LIMITED WARRANTY

44
Never perform a temporary repair, use an
innertube or inject sealant as a permanent
substitute for a proper repair. Only qualified
persons should repair tires.
Be sure that all your valves have suitable valve
caps. This will keep valve cores clean and clear
and guard against leakage.
REPAIRS - WHENEVER POSSIBLE, SEE
A TIRE RETAILER AT ONCE.Some tire
manufacturers do not warrant any inspection
or repair process. The repair is entirely the
responsibility of the repairer. Punctures in
the tread of a passenger tire which do not
exceed 1/4 of an inch (6mm) in diameter can
usually be repaired by following the Rubber
Manufacturer’s Association (RMA) Passenger
and Light Truck Repair procedures. Contact
the manufacturer of your tires for its position
and assistance as to the acceptable location
for a proper repair and the repair of speed
rated tires. Do not use plug repairs. They may
cause further damage to the tire. They are not
always air tight and the plug may fail. Do not
exceed posted speed limits on any repaired tire.
Certain tire manufacturers speed ratings are
voided if the tire is repaired.
Although a tire was properly repaired, internal
structural damage resulting from the puncture
may have occurred.
Sometime later the damage may cause the tire
to be removed from service.
If the tire has a puncture in the tread which
exceeds 1/4 inch (6mm), the tire must be replaced. If any tire has sustained a puncture,
have the tire inspected internally by a tire
retailer for possible damage that may have
occurred.
Improper mounting and inflation procedures
can cause an explosion of the tire/rim
assembly. Only specially trained persons should
perform these tasks. Contact your tire store or
retailer for assistance.
CAUTION - Never, under any circumstance,
introduce a flammable substance into a tire.
WHEEL ALIGNMENT AND BALANCING
Wheel alignment and balancing are important
for safety and maximum mileage from your
tires. Check how your tires are wearing at
least once a month. If your tires are wearing
unevenly, such as the inside shoulder of the
tire wearing faster than the rest of the tread,
or if you detect excessive vibration, your
vehicle may be out of alignment or balance.
These conditions not only shorten the life of
your tires, but adversely affect the handling
characteristics of your vehicle which could
be dangerous. If you detect irregular wear or
vibration, have your alignment and balance
checked immediately. Tires which have been
run underinflated will show more wear on the
shoulders than in the center of the tread.
HARD BRAKING
You must inspect your tires after any hard
braking circumstances or after tires have slid
on the pavement. This can cause a flat spot in
a section of the tire tread. TIRE SPINNING
Never spin your tires above a speedometer
reading of 35 mph (55 km/h) if your vehicle
becomes stuck. The centrifugal force
generated by the free spinning tire/wheel
assembly may cause a sudden tire explosion,
resulting in vehicle damage and/or serious
personal injury or death. Never allow anyone
to stand near or behind a tire spinning at high
speed while attempting to push a vehicle that
is stuck. When in mud, sand, snow, ice or other
slippery conditions, do not indulge in excessive
wheel spin. In such conditions, with automatic
transmission vehicles, by accelerating the
engine excessively, it is possible to spin one of
the drive tires beyond its speed capability. This
is also true when balancing a drive tire/wheel
assembly using the engine of the vehicle to
spin the wheel.
TIRE TREAD
Tires must be replaced when the depth of
the tread reaches 2/32 inch (1.6 mm). Tires
are manufactured with tread wear indicators
molded into the tire grooves which indicate
tread wearout. As tires approximate 2/32 inch
(1.6 mm) wearout, the tread gauge becomes
thinner and more vulnerable to the effects
of road hazards. Also, worn tires are more
subject to hydroplaning, which can cause loss
of control. Therefore, visual tire inspection
becomes more crucial as the tires wear out.
(Continued on next page)
IMPORTANT TIRE SAFETY INFORMATION¹