2019 INFINITI QX30 set clock

If you are driving at speeds above approxi-
mately 34 MPH (55 km/h) and no other road
users are detected, the high beam headlights
are switched on automatically. The
indicator light in the combination meter also
lights up.
If you are driving at speeds below approxi-
mately 28 MPH (45 km/h) or other road
users are detected or the roads are ad-
equately lit The high beam headlights are
switched off automatically. The
indica-
tor light in the combination meter goes out.
The
indicator light in the vehicle infor-
mation display remains lit.
To deactivate:
Move the combination switch back to its nor-
mal position The
indicator light in the
vehicle information display goes out.
HEADLIGHTS MISTED UP ON
THE INSIDE
Certain climatic and physical conditions may
cause moisture to form in the headlight. This
moisture does not affect the functionality of
the headlight.
INSTRUMENT BRIGHTNESS
CONTROL
The light sensor in the combination meter
automatically controls the brightness of the
instrument panel
In daylight, the displays in the combination
meter are not illuminated
The lighting in the combination meter, dis-
plays and controls in the vehicle interior can
be adjusted using the brightness control
knob.
The brightness control knob
1is located
behind the steering wheel.
Turn the brightness control knob clockwise or
counterclockwise. If the light switch is set to
orthe brightness is dependent
upon the brightness of the ambient light.
FRONT FOG LIGHTS
In conditions where visibility is poor due to
fog, snow or rain, the fog lights improve vis-
ibility as well as making it easier for other
road users to see you. They can be operated
together with the side lights or together with
the side lights and low beam headlights.
To switch on the fog lights:
•Turn the ignition switch to the ON position
or start the engine.
•Turn the light switch toor.
•Press thebutton. The greenindicator light in the combination meter
lights up
NIC2615NIC2699
FOG LIGHT SWITCH (IF SO
EQUIPPED)
Instruments and controls2-71

If the battery cable is disconnected, the clock
will need to be re-adjusted to the correct
time.
ADJUSTING TIME
Set the time using the INFINITI controller and
the [Settings] menu available in the central
display (see your INFINITI InTouch Owner's
Manual).
NOTE
On vehicles fitted with a navigation system,
the clock is automatically updated via GPS.
The initial clock setting may be incorrect.
In the center console (LHD)
Rear console
The power outlet is used for powering elec-
trical accessories such as a cellular telephone.
An emergency cut-off ensures that the on-
board voltage does not drop too low. If the
on board voltage is too low, the power to the
sockets is automatically cut. This ensures that
there is sufficient power to start the engine.
CAUTION
•The outlet and plug may be hot during or
immediately after use.
•Only certain power outlets are designed
for use with a cigarette lighter unit. Do
not use any other power outlet for an
accessory lighter. It is recommended you
visit an INFINITI retailer for additional
information.
•Do not use with accessories that exceed
a 12 volt, 180W (15A) power draw. Do
not use double adapters or more than
one electrical accessory.
•Use this power outlet with the engine
running to avoid discharging the vehicle
battery.
•Avoid using when the air conditioner,
headlights or rear window defogger is on.
NSD659NIC2690
NIC2683
CLOCK POWER OUTLET
Instruments and controls2-79

AIR CONDITIONING SYSTEM
1Sets the temperature
2De-ices/defogs the windshield
3Set the air distribution
4Activates/deactivates air-recirculation
mode
5Sets the airflow
6Activates/deactivates cooling with air
dehumidification
7Switches the rear window defroster on/
off
Operating tips
A number of tips and recommendations for
optimum use of the air-conditioning system
are listed below:
•Switch on the air-conditioning system by
turning control knob
5clockwise to the
desired position (except position0)
•Set the temperature to 70° F (22° C)
•Recommendation for avoiding misted
windows at low exterior temperatures or
in rain: switch on the
cooling with
dehumidification function. Set air distri-
bution to
and if possible switch
offand. Deactivate air-
recirculation mode.
Set airflow control
5to a setting be-
tween 3 and 6.
•Recommendation for rapid cooling or
heating of the vehicle interior: briefly set
airflow control
5to a setting between 3
and 6.
•Recommendation for a constant vehicle
interior temperature: set airflow control
5to a setting between 1 and 3.
NAA1644
4-30Display screen, heater and air conditioner, and audio system

•Recommendation for air distribution in
winter: select theandsettings.
Recommendation for air distribution in
summer: select the
orandsettings.
•Only use the "Windshield demisting" func-
tion briefly until the windshield is clear again
•Only use air-recirculation mode briefly, for
example if there are unpleasant outside
odors or when in a tunnel. The windows
could otherwise mist up as no fresh air is
drawn into the vehicle in air-recirculation
mode
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds
at the bottom of the screen in the central
display (see separate operating instruc-
tions). You will see the current settings of
the various climate control functions.
Switching air-conditioning system
on/off
Make sure the ignition switch is in the ON
position.
To switch on:turn control
5clockwise to the
desired position (except position0).
To switch off:turn control
5counter-
clockwise to position0.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate the "Cooling with air dehu-
midification" function, the air inside the ve-
hicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can mist up more quickly. There-
fore, only deactivate the "Cooling with air
dehumidification" function briefly.
The "Cooling with air dehumidification" func-
tion is only available when the engine is run-
ning. The air inside the vehicle is cooled and
dehumidified according to the temperature
selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This
is normal and not a sign that there is a mal-
function.
To activate:
Press the
button The indicator light in
thebutton lights up.
To deactivate:
Press the
button. The indicator light in
thebutton goes out. The cooling with
air dehumidification function has a delayed
switch-off feature.Problems with the "Cooling with air dehu-
midification" function:
Problem:The indicator light in the
but-
ton flashes three times or remains off. The
cooling with air dehumidification function
cannot be activated.
Cause and solution:The cooling with air de-
humidification function has been deactivated
due to a malfunction. Have the system
checked. It is recommended you visit an
INFINITI retailer for this service.
Setting the temperature
You can set the temperature for the entire
vehicle. The set temperature is automatically
maintained at a constant level.
To increase or reduce the temperature: turn
control
1counterclockwise or clockwise.
Only change the temperature setting in small
increments. Start at 70° F (22° C).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the foot-
well air ventilators.
Display screen, heater and air conditioner, and audio system4-31

NOTE
•You can also activate several of the air
distribution settings simultaneously. In
order to do this, press several of the air
distribution buttons. The air is then
routed through different air ventilators.
•Regardless of the air distribution setting,
airflow is always directed through the
side air ventilators. The side air ventila-
tors can only be closed if the adjusters are
turned clockwise until they engage.
To set air distribution:
1. Make sure the engine is running.
2. Press one or more of the
,,orbuttons. The corresponding indica-
tor light comes on.
Setting the airflow
1. Make sure the ignition switch is in the ON
position.
2. To increase or reduce airflow: turn control
5counterclockwise or clockwise.
Defogging the windshield
You can use this function to de-ice the wind-
shield or to defog the inside of the windshield
and the side windows.
NOTE
You should only select the "Windshield de-
misting" function until the windshield is clear
again.
Activating the "Windshield demisting"
function:
Make sure the ignition switch is in the ON
position.
To activate: press the
button The indi-
cator light in thebutton lights up.
The climate control system switches to the
following functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air-recirculation mode offNOTE
•The "Windshield demisting" function au-
tomatically sets the blower output to the
optimum demisting effect. As a result, the
airflow may increase or decrease auto-
matically after the
button is
pressed.
•You can adjust the blower output manu-
ally while the "Windshield demisting"
function is in operation. Turn airflow con-
trol
5counterclockwise or clockwise.
Deactivating the "Windshield demisting"
function:
Press the
button. The indicator light in
thebutton goes out. The previous set-
tings are reactivated. Air-recirculation mode
remains deactivated.
or
Turn temperature control
1counterclock-
wise or clockwise.
Defogging the windows
Windows misted up on the inside:
1. Activate the
"Cooling with air dehu-
midification" function.
2. If the windows continue to mist up, acti-
vate the
"Windshield demisting"
function.
4-32Display screen, heater and air conditioner, and audio system

The system automatically regulates the tem-
perature of the dispensed air, the airflow and
the air distribution.
The automatic mode functions optimally
when the "Cooling with air dehumidification"
function is activated. If desired, cooling with
air dehumidification can be deactivated.
If you deactivate the "Cooling with air-
dehumidification" function, the air inside the
vehicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can mist up more quickly. There-
fore, only deactivate the "Cooling with air-
dehumidification" function briefly.
To set climate control to automatic mode:
Make sure the ignition switch is in the ON
position.
Set the desired temperature.
To activate: press the
button The indi-
cator light in thebutton lights up. Auto-
matic air distribution and airflow are activated.
To switch to manual mode: press theorbutton
or
Press the
orbutton. The indicator
light in thebutton goes out. Automatic
air distribution and airflow are deactivated.
Setting the temperature
Different temperatures can be set for the
driver's and front-passenger sides. The set
temperature is automatically maintained at a
constant level.
Make sure the ignition switch is in the ON
position.
To increase or reduce temperature: turn con-
trol
1or9counterclockwise or clockwise.
Only change the temperature setting in small
increments. Start at 70° F (22° C).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the foot-
well air ventilators.
Directs the airflow through the center
and side air ventilators as well as the
footwell air ventilators.
Directs the airflow through the center
and side air ventilators as well as the
demister ventilators.
Directs the airflow through the foot-
well and demister ventilators.
Directs the airflow through the demis-
ter ventilators, the center and side air
ventilators as well as the footwell air
ventilators.NOTE
Regardless of the air distribution setting,
airflow is always directed through the side
air ventilators. The side air ventilators can
only be closed if the adjusters are turned
clockwise until they engage.
To set the air distribution:
1. Make sure the engine is running.
2. Press the
orbutton repeat-
edly until the desired symbol appears in
the display.
Setting the airflow
1. Make sure the ignition switch is in the ON
position.
2. To increase or reduce airflow: press the
orbutton.
Switching the ZONE function
on/off
This function is only available with automatic
climate control.
To activate:press the
button. The in-
dicator light in thebutton lights up. The
temperature setting for the driver's side is not
adopted for the front-passenger side.
To deactivate:press the
button. The
indicator light in thebutton goes out.
4-36Display screen, heater and air conditioner, and audio system

The temperature setting for the driver's side
is adopted for the front-passenger side.
Defogging the windshield
You can use this function to de-ice the wind-
shield or to defog the inside of the windshield
and the side windows.
NOTE
You should only select the "Windshield de-
misting" function until the windshield is clear
again.
Activating the "Windshield demisting"
function:
Make sure the ignition switch is in the ON
position.
To activate: press the
button The indi-
cator light in thebutton lights up.
The climate control system switches to the
following functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air-recirculation mode offNOTE
•The "Windshield demisting" function au-
tomatically sets the blower output to the
optimum demisting effect. As a result, the
airflow may increase or decrease auto-
matically after the
button is
pressed.
•You can adjust the blower output man-
ually while the "Windshield demisting"
function is in operation. Press the
orbutton.
Deactivating the "Windshield demisting"
function:
Press the
button. The indicator light in
thebutton goes out. The previous set-
tings are reactivated Air-recirculation mode
remains deactivated.
or
Turn temperature control
1or9counter-
clockwise or clockwise.
Defogging the windows
Windows misted up on the inside:
1. Activate the
"Cooling with air dehu-
midification" function.
2. Activate automatic mode
.3. If the windows continue to mist up, acti-
vate the
"Windshield demisting"
function.
NOTE
You should only select this setting until the
windshield is clear again.
Windows misted up on the outside:
1. Activate the windshield wipers.
2. Set the air distribution to
or.
NOTE
You should only select this setting until the
windows are clear again.
Air recirculation mode
You can deactivate the flow of fresh air if
unpleasant odors are entering the vehicle
from outside. The air already inside the ve-
hicle will then be recirculated.
If you activate air-recirculation mode, the
windows can mist up more quickly, in particu-
lar at low temperatures. Only use air recircu-
lation mode briefly to prevent the windows
misting up.
Activating air recirculation mode:
Make sure the ignition switch is in the ON
position.
Display screen, heater and air conditioner, and audio system4-37

REINITIALISATION PROCEDURE
AFTER BATTERY
RECONNECTION
If the battery has been reconnected, check
the following items:
•Clock setting (if so equipped). For details,
see "Clock", or the separately provided
INFINITI InTouch Owner’s Manual.
•Reset the desired radio stations to the pre-
set station buttons. For details, see the
audio device descriptions in the separately
provided INFINITI InTouch Owner’s
Manual.
JUMP-STARTING
If jump-starting is necessary, see "Jump
starting". If the engine does not start by jump
starting, the battery may have to be replaced.
It is recommended that you visit an INFINITI
retailer for this service.
WARNING
Be sure the ignition switch is in the OFF
position before servicing drive belt. The en-
gine could rotate unexpectedly.
1. Visually inspect each belt for signs of un-
usual wear, cuts, fraying or looseness. If
the belt is in poor condition or loose, have
it replaced or adjusted. It is recommended
that you visit an INFINITI retailer for this
service.
2. Have the belts checked regularly for con-
dition and tension in accordance with the
maintenance schedule as shown in a
separately provided Warranty Informa-
tion and Maintenance booklet.Replace the spark plugs according to the
maintenance schedule shown in a separate
maintenance booklet.
If replacement is required, it is recommended
that you visit an INFINITI retailer.
Always replace spark plugs with recom-
mended or equivalent ones.
WARNING
Be sure the engine and ignition switch are
off and that the parking brake is engaged
securely.
CAUTION
•Be sure to use the correct socket to re-
move the spark plugs. An incorrect
socket can cause damage to the spark
plugs.
DRIVE BELT SPARK PLUGS
8-12Do-it-yourself