2019 INFINITI QX30 lock

•Exterior lighting delayed switch-off: the
exterior lighting remains lit for 60 seconds
after the engine is switched off. If you
close all the doors and the lift gate, the
exterior lighting goes off after 15 seconds.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press theorbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Surround Lighting] function.
5. Press the button to save the setting.
When the [Surround Lighting] function is
activated, the light cone and the area
around the vehicle are displayed in orange
in the vehicle information display
6. Press the button to confirm the set-
ting.
Deactivating delayed switch-off of the exte-
rior lighting temporarily:
1. Before leaving the vehicle, switch the igni-
tion switch to the OFF position.
2. Switch the ignition switch to the ON po-
sition.
The exterior lighting delayed switch-off is
deactivated.Delayed switch-off of the exterior lighting
is reactivated the next time you start the
engine.
Depending on your vehicle's equipment,
when the surround lighting and delayed
switch-off exterior lighting are on, the fol-
lowing light up:
•Side lights
•Fog lights
•Low beam headlights
•Daytime driving lights
•Surround lighting in the exterior mirrors
Activating/deactivating the interior light-
ing delay:
If you activate the [Interior Lighting Delay]
function, the interior lighting remains on for
20 seconds after you remove the key from
the ignition lock.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.4. Press the
orbutton to select
the [Interior Lighting Delay] function. If
the [Interior lighting delayed switch-off]
function has been switched on, the vehicle
interior is displayed in orange in the ve-
hicle information display
5. Press the button to save the setting.
Vehicle
Setting permanent speed limiter:
You can set permanent speed limiter using
the [Limit Speed (Winter Tires)] function.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Vehicle] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Limit Speed (Winter Tires)] function.
You will see the selected setting.
5. Press to confirm.
6. Press the
orbutton to adjust
permanent speed limiter in increments of
ten ([150 mph] to [100 mph]), [240 km/h]
to [160 km/h]). The [Off] setting switches
permanent speed limiter off).
Instruments and controls2-27

7. Press the orbutton to store
the entry.
Activating/deactivating the acoustic lock-
ing confirmation:
If you switch on the [Acoustic Lock Feed-
back] function, an acoustic signal sounds
when you lock the vehicle.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Vehicle] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Acoustic Lock Feedback] function.
If the [Acoustic Lock Feedback] function
is activated, the
symbol in the ve-
hicle information display lights up orange.
5. Press the button to save the setting.
Convenience
Switching the [Fold Mirrors in when Lock-
ing] function on/off:
This function is only available when the ve-
hicle is equipped with the electrical fold-in
function.When you activate the [Fold Mirrors in when
Locking] function, the exterior mirrors are
folded in when the vehicle is locked. If you
unlock the vehicle and then open the driver's
or front passenger door, the exterior mirrors
fold out again.
If you have switched on the [Fold Mirrors in
when Locking] function and you fold in the
exterior mirrors using the button on the door
(see "Folding"), they will not fold out auto-
matically. The exterior mirrors can then only
be folded out using the button on the door.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Convenience] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Fold Mirrors in when Locking] func-
tion.
If the [Fold Mirrors in when Locking]
function is activated, the vehicle's exterior
mirror is shown in orange in the vehicle
information display.
5. Press the button to save the setting.
Resetting to factory settings
1. Press theorbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Factory Setting] submenu.
3. Press to confirm.
The [Reset All Settings?] message ap-
pears.
4. Press the
orbutton to select
[No] or [Yes].
5. Press the button to confirm the se-
lection.
If you have selected [Yes], the vehicle in-
formation display shows a confirmation
message.
For safety reasons, not all functions are reset:
the [Limit Speed (Winter Tires)] function in
permanent speed limiter can only be set in the
[Vehicle] submenu.
If you want to reset the Daytime driving lights
function in the Lights submenu, you must
switch the ignition switch to the ACC
position.
2-28Instruments and controls

Safety systems
Message Possible causes/consequences and solutions
[Currently Unavailable See
Operator's Manual]ABS (Anti-Lock Braking System), BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are temporarily
unavailable.
Forward Emergency Braking (FEB) may also have failed.
In addition, the,andwarning lights may light up in the combination meter.
Possible causes:
•Self-diagnosis is not yet complete.•The on-board voltage may be insufficient.
WARNING
The brake system continues to function normally, but without the functions listed above. The wheels could therefore lock if you
brake hard, for example.
The steering and braking characteristics may be severely affected. The braking distance may increase in an emergency braking
situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Carefully drive on a suitable stretch of road, making slight steering movements, at a speed above 12 MPH (20 km/h). If the display
message disappears, the functions mentioned above are available again.
If the display message continues to be displayed, drive on carefully and have the system checked. It is recommended you visit an
INFINITI retailer for this service.
2-30Instruments and controls

Message Possible causes/consequences and solutions
[Inoperative See Operator's
Manual]ABS (Anti-Lock Braking System), BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are not available
due to a malfunction.
Forward Emergency Braking (FEB) may also have failed.
In addition, the,,andwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above. The wheels could therefore lock if you
brake hard, for example.
The steering and braking characteristics may be severely affected. The braking distance may increase in an emergency braking
situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
[Currently Unavailable See
Operator's Manual]BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are temporarily unavailable.
Forward Emergency Braking (FEB) may also have failed.
In addition, theandwarning lights may light up in the combination meter.
The self-diagnosis function, for example, may not be complete.
WARNING
The brake system continues to function normally, but without the functions listed above.
The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Carefully drive on a suitable stretch of road, making slight steering movements, at a speed above 12 MPH (20 km/h). If the display
message disappears, the functions mentioned above are available again.
If the display message continues to be displayed, drive on carefully and have the system checked. It is recommended you an INFINITI
retailer for this service.
Instruments and controls2-31

Message Possible causes/consequences and solutions
[Inoperative See Operator's
Manual]BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are not available due to a malfunction.
Forward Emergency Braking (FEB) may also have failed.
In addition, theandwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above.
The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Inoperative See Operator's
Manual]EBD (Electronic Brake Force Distribution) ABS (Anti-Lock Braking System), BAS (Brake Assist System), VDC (Vehicle Dynamic
Control), and hill start assist are not available due to a malfunction.
Forward Emergency Braking (FEB) may also have failed.
A warning tone sounds.
In addition, the,andwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above. The front and rear wheels could
therefore lock if you brake hard, for example.
The steering and braking characteristics may be severely affected. The braking distance may increase in an emergency braking
situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
[Turn On The Ignition to
Release the Parking Brake]The redindicator light lights up.
You attempted to release the electric parking brake while the ignition was switched off.
Key: turn the key to the ON position in the ignition switch
2-32Instruments and controls

Message Possible causes/consequences and solutions
The yellow
warning light is lit. If you manually apply or release the electric parking brake, the redindicator light flashes.
The electric parking brake is malfunctioning. It is not possible to apply the electric parking brake manually.
or
Insert the seat belt in the belt buckle and accelerate slightly more when pulling away.
Press the P (Park) button, as the electric parking brake is not applied automatically.
It is recommended you consult an INFINITI retailer.
If you do not wish the electric parking brake to be applied, leave the ignition switched on, e. g. when washing the vehicle in an
automatic car wash or when having the vehicle towed.
[Parking Brake Inoperative]The yellowwarning light is lit. The redindicator light flashes for about ten seconds after the electric parking brake
has been applied or released. It then goes out or remains lit.
The electric parking brake is malfunctioning, e.g. because of overvoltage or undervoltage.
1. Rectify the cause of the overvoltage or undervoltage, e.g. by charging the battery or restarting the engine.
2. Apply or release the electric parking brake.
If the electric parking brake still cannot be applied or released:
1. Switch the ignition off and turn it back on.
2. Apply or release the electric parking brake manually.
If the electric parking brake still cannot be applied or released, it is recommended you consult an INFINITI retailer.
The yellow
warning light is lit. The redindicator light flashes.
It is not possible to apply the electric parking brake manually.
1. Press the P (Park) button.
Consult an INFINITI retailer.
[Brake Immediately]A tone may also sound at regular intervals. If you attempt to lock the vehicle, the tone becomes louder.
You cannot start the engine.
1. Paying attention to the traffic situation, immediately depress the brake pedal firmly and hold until the display message
disappears.
2. Secure the vehicle against rolling away. You can restart the engine.
Instruments and controls2-35

Engine
Message Possible causes/consequences and solutions
[Check Coolant Level See
Operators Manual]The coolant level is too low.CAUTIONAvoid making long journeys with too little coolant in the engine cooling system. The engine will otherwise be damaged.
Top up the coolant, observing the warning notes before doing so (see "If your vehicle overheats").
If the coolant needs topping up more often than usual. have the engine coolant system checked. It is recommended you visit an
INFINITI retailer for this service.
The fan motor is faulty.
If the coolant temperature is below 250°F (120°C), you can continue driving to the nearest place you can have the system checked.
It is recommended that you visit an INFINITI retailer for this service.
Avoid putting the engine under heavy load as you do so, e.g. driving in mountainous terrain and stop-start traffic.
[Coolant Too Hot Stop
Vehicle Turn Engine Off]The coolant is too hot.
A warning tone also sounds.CAUTIONIf the gauge indicates coolant temperature near the hot (H) end of the normal range, reduce vehicle speed to decrease tempera-
ture. If the gauge is over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued
operation of the vehicle may seriously damage the engine. For additional information, refer to "If your vehicle overheats" for
immediate action required.
1. Stop the vehicle immediately, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away
3. Wait until the engine has cooled down.
4. Make sure that the air supply to the engine radiator is not blocked, e.g. by frozen slush.
5. Do not start the engine again until the display message goes out and the coolant temperature is below 120°C. The engine may
otherwise be damaged.
6. Pay attention to the coolant temperature display.
7. If the temperature increases again, have the system checked immediately. It is recommended you visit an INFINITI retailer for
this service.
Under normal operating conditions and with the specified coolant level, the coolant temperature may rise to 250°F (120°C).
See "If your vehicle overheats".
Instruments and controls2-45

Vehicle
Message Possible causes/consequences and solutions
[Depress Brake to Start
Engine](DCT models only). You have attempted to start the engine with the transmission in position N (Neutral) without depressing the
brake pedal.
Depress the brake pedal.
[To Deselect P or N,
Depress Brake and Start
Engine]You have attempted to shift the shift lever to position R (Reverse) or D (Drive) without starting the engine.
Start the engine and depress the brake pedal.
NOTE•It is only possible to move the shift lever from position P (Park) to the desired position if you depress the brake pedal. Only then
can the parking lock be deactivated.
•At transmission fluid temperatures below -5°F (-20°C) you can only shift out of position P (Park) into another transmission
position when the engine is running.
[Apply Brake to Shift
From 'P']You have attempted to shift the shift lever to position R (Reverse), N (Neutral) or D (Drive) without depressing the brake pedal.
Depress the brake pedal.
[Risk of Rolling Transmis-
sion Not in P]The driver's door is open/not fully closed and the shift lever is in position R (Reverse), N (Neutral) or D (Drive).
A warning tone also sounds
WARNING
The vehicle may roll away.
There is a risk of an accident.
1. Press the P (Park) button.
2. Secure the vehicle against rolling away.
3. Close the driver's door fully.
[Service Required Do Not
Shift Gears Visit Dealer]You cannot change the transmission position due to a malfunction.
A warning tone also sounds.
If transmission position D (Drive) is selected, Drive to an INFINITI retailer without shifting the transmission from position D (Drive).
If transmission position R (Reverse), N (Neutral) or P (Park), secure the vehicle against rolling away. It is recommended you consult
an INFINITI retailer.
2-54Instruments and controls