2019 INFINITI QX30 window

Message Possible causes/consequences and solutions
[Steering Malfunction See
Operator's Manual]The electric steering lock is malfunctioning.WARNING
The steering may be locked by the electric steering lock.
There is a risk of an accident.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Do not drive on. It is recommended you contact the nearest INFINITI retailer.
The electric steering lock was unable to unlock the steering.
1. Remove the key from the ignition switch.
2. To unlock the steering, move the steering wheel slightly.
3. Insert the key into the ignition lock again.
[Check Washer Fluid]The washer fluid level in the washer fluid reservoir has dropped below the minimum.
Top up the washer fluid (see "Window washer fluid")
[Wiper Malfunctioning] The windshield wipers are defective.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Hazard Warning Flashers
Malfunctioning]The hazard warning lights are faulty.
Visit an INFINITI retailer.
Instruments and controls2-57

To switch the alarm off with the key: press
theorbutton on the key. The
alarm is switched off
or
Vehicles with a push button ignition switch:
•Remove the start/stop button from the
ignition lock (see " Push-button ignition
switch (if equipped)")
•Insert the key into the ignition lock. The
alarm stops.
The alarm is not switched off, even if you
close the open door that has triggered it, for
example.
WARNING
In freezing temperatures the washer solu-
tion may freeze on the windshield and ob-
scure your vision which may lead to an ac-
cident. Warm the windshield with the
defroster before you wash the windshield.
CAUTION
•Do not operate the washer continuously
for more than 30 seconds.
•Do not operate the washer if the win-
dow washer fluid reservoir is empty.
•Do not fill the window washer reservoir
tank with washer fluid concentrates at
full strength. Some methyl alcohol
based washer fluid concentrates may
permanently stain the grille if spilled
while filling the window washer reser-
voir tank.
•Pre-mix washer fluid concentrates with
water to the manufacturer’s recom-
mended levels before pouring the fluid
into the window washer reservoir tank.
Do not use the window washer reservoir
tank to mix the washer fluid concentrate
and water.NOTE
•If the wiper operation is interrupted by
snow or ice, the wiper may stop moving to
protect its motor. If this occurs, turn the
wiper switch to the “OFF” position and
remove the snow or ice on and around the
wiper arms. In approximately 1 minute,
turn the switch on again to operate the
wiper.
•Do not operate the windshield wipers
when the windshield is dry, as this could
damage the wiper blades. Moreover, dust
that has collected on the windshield can
scratch the glass if wiping takes place
when the windshield is dry.
•If it is necessary to switch on the wipers in
dry weather conditions, always operate
them using washer fluid.
•If the windshield wipers leave smears on
the windshield after the vehicle has been
washed in an automatic car wash, this
may be due to wax or other residue. Clean
the windshield with washer fluid after an
automatic car wash.
WIPER AND WASHER SWITCH
Instruments and controls2-61

•Vehicles with a rain sensor: if the wind-
shield becomes dirty in dry weather con-
ditions, the windshield wipers may be
activated inadvertently. This could
damage the windshield wiper blades or
scratch the windshield.
For this reason, you should always
switch off the windshield wipers in dry
weather.
Vehicles with a rain sensor: in the
orposition, the appropriate wiping fre-
quency is automatically set according to the
intensity of the rain. In the
position, the
rain sensor is more sensitive than in the
position, causing the windshield wiper
to wipe more frequently.
If the wiper blades are worn, the windshield
will no longer be wiped properly. This could
prevent you from observing the traffic condi-
tions.
SWITCHING THE REAR WINDOW
WIPER ON/OFF
WARNING
In freezing temperatures the washer solu-
tion may freeze on the windshield and ob-
scure your vision which may lead to an ac-
cident. Warm the windshield with the
defroster before you wash the windshield.
CAUTION
•Do not operate the washer continuously
for more than 30 seconds.
•Do not operate the washer if the win-
dow washer fluid reservoir is empty.
•Do not fill the window washer reservoir
tank with washer fluid concentrates atfull strength. Some methyl alcohol
based washer fluid concentrates may
permanently stain the grille if spilled
while filling the window washer reser-
voir tank.
•Pre-mix washer fluid concentrates with
water to the manufacturer’s recom-
mended levels before pouring the fluid
into the window washer reservoir tank.
Do not use the window washer reservoir
tank to mix the washer fluid concentrate
and water.
1Switch
2Wipes with washer fluid
3Switches on intermittent wiping
4Switches off intermittent wiping
5Wipes with washer fluid
1. Switch the ignition switch to the ON po-
sition.
2. Turn switch
1on the combination switch
to the corresponding position.
When the rear window wiper is switched
on, the
symbol appears in the as-
sistance graphic in the combination meter.
Further information on the assistance
graphic (see "Showing the distance
display" earlier in this section).
NIC2617
Instruments and controls2-63

The defroster switchBoperates when the
ignition switch is in the ON position for the
rear window, and (if equipped) for the outside
rear view mirrors.
The defroster is used to reduce the moisture,
fog or frost on the rear window surface and
on the outside mirror surface to improve the
rear view.
When the defroster switch
is pushed,
the indicator light illuminates and the de-
froster operates for several minutes. After
the preset time has passed, the defroster will
turn off automatically. To turn off the de-
froster manually, push the defroster switch
again, and the indicator light turns off.
CAUTION
•When cleaning the inner side of the rear
window, be careful not to scratch or
damage the rear window defroster.
•When operating the defroster con-
tinuously, be sure to start the engine.
Otherwise, it may cause the battery to
discharge.
•When cleaning the inner side of the win-
dow, be careful not to scratch or dam-
age the electrical conductors on the sur-
face of the window.The windshield de-icer switch (defogger
switch)
Aoperates when the ignition switch
is in the ON position.
You can use this function to defrost the wind-
shield or to demist the inside of the wind-
shield and the side windows
NOTE
You should only select the windshield de-icer
function until the windshield is clear again.
When the switch
is pushed, the indica-
tor light in the switch illuminates. The climate
control system switches to the following
functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air recirculation mode off
NAA1659NAA1659
REAR WINDOW AND OUTSIDE
MIRROR DEFROSTER SWITCHWINDSHIELD DE-ICER SWITCH (IF
EQUIPPED)
2-64Instruments and controls

NOTE
The seat heater can only be activated
when the ignition switch is in the ON po-
sition.
2. Start the engine.
3. Select the heat range:
•To switch on: press button1repeat-
edly until the desired heating level is
set.
•To switch off: press button1repeat-
edly until all the indicator lights turn off.
NOTE
If the battery voltage is too low, the seat
heating may switch off.
POWER WINDOWS
WARNING
•Make sure that all passengers have their
hands, etc. inside the vehicle while it is in
motion and before closing the windows.
Use the window lock switch to prevent
unexpected use of the power windows.
•To help avoid risk of injury or death
through unintended operation of the
vehicle and or its systems, including en-
trapment in windows or inadvertent
door lock activation, do not leave chil-
dren, people who require the assistance
of others or pets unattended in your ve-
hicle. Additionally, the temperature in-
side a closed vehicle on a warm day can
quickly become high enough to cause a
significant risk of injury or death to
people and pets.
The switches for all side windows are located
on the driver's door. There is also a switch on
each door for the corresponding side window
The switches on the driver's door take prece-
dence.
Auto-reverse function
The auto-reverse function can be activated
when a window is closed by automatic op-
eration.
Depending on the environment or driving con-
ditions, the auto-reverse function may be ac-
tivated if an impact or load similar to some-
thing being caught in the window occurs.
WARNING
There are some small distances immedi-
ately before the closed position which can-
not be detected. Make sure that all passen-
gers have their hands, etc., inside the
vehicle before closing the window.
If the vehicle's battery is disconnected, re-
placed, or jump started, the power window
auto-reverse function may not operate prop-
erly. If this occurs, it is recommended you visit
an INFINITI retailer to re-initialize the power
window auto-reverse system.
If the control unit detects something caught
in a window equipped with automatic opera-
tion as it is closing, the window will be imme-
diately lowered.
WINDOWS
2-74Instruments and controls

Driver’s window switch
The power windows operate when the igni-
tion switch is in the ON position.
1. Front left side window
2. Front right side window
3. Rear left side window
4. Rear right side window
The driver’s switch, the main switch, can con-
trol all windows.
•To open manually: press and hold the cor-
responding button.
•To open fully: press the button beyond the
point of resistance to the second detent and
release it. Automatic operation is started.
•To close manually: pull the corresponding
button and hold it.
•To close fully: pull the button beyond the
point of resistance and release it. Auto-
matic operation is started.
•To interrupt automatic operation: press/
pull the corresponding switch again.
NOTE
•If you press/pull the switch beyond the
point of resistance, automatic operation
is started in the corresponding direction.
You can stop automatic operation by
pressing/pulling again.
•You can continue to operate the side win-
dows after switching off the engine or re-
moving the key. This function remains ac-
tive for five minutes or until the driver's or
front-passenger door is opened.
•The side windows cannot be operated
from the rear when the override feature
for the side windows is activated.
NIC2715
Instruments and controls2-75

Locking rear side windows:
To enable/disable the override feature for
the rear side windows, press button
2.If
indicator light
1is lit, operation of the rear
side windows is disabled. Operation is only
possible using the switches in the driver's
door. If indicator light
1is off, operation is
possible using the switches in the rear com-
partment.
Passenger’s window switch
The passenger’s switch can control its corre-
sponding window.
Convenience opening feature
For vehicles with Intelligent Key:you can
ventilate the vehicle before you start driving.
The key can also be used to carry out the
following functions simultaneously:
•Unlock the vehicle
•Open the side windows
NOTE
The convenience opening feature can only be
operated using the key.
The key must be in close proximity to the
vehicle.Press and hold the
button until the side
windows are in the desired position.
To interrupt convenience opening: release
the
button.
Convenience closing feature
WARNING
When the convenience closing feature is
operating, parts of the body could become
trapped in the closing area of the side win-
dow. There is a risk of injury. Observe the
complete closing procedure when the con-
venience closing feature is operating.
When closing make sure that no parts of
the body are in the closing area.
For vehicles with Intelligent Key:The key can
also be used to carry out the following func-
tions simultaneously:
•Lock the vehicle
•Close the side windows
The driver's door and the door at which the
handle is used must both be closed. The key
must be outside the vehicle. The gap between
the key and the corresponding door handle
should not be greater than 1 m.
NIC2716NIC2640
2-76Instruments and controls

Press and hold thebutton until the side
windows are fully closed.
To interrupt convenience closing: release the
button.
You can also use the keyless locking feature
to activate convenience closing:
Touch recessed sensor surface
1on the
door handle until the side windows are fully
closed.
NOTE
Make sure you only touch recessed sensor
surface
1.
To interrupt convenience opening: release
the recessed sensor surface
1on the door
handle.
Resetting the side windows
If a side window can no longer be closed fully,
you must reset it.
1. Switch the ignition switch to the ON po-
sition.
2. Close the door.3. Pull the corresponding switch on the door
control panel until the side window is
completely closed
4. Hold the switch for an additional second.
If the side window opens again slightly:
1. Immediately pull the corresponding switch
on the door control panel until the side
window is completely closed.
2. Hold the switch for an additional second.
3. If the corresponding side window remains
closed after the button has been released,
the side window has been reset correctly.
If this is not the case, repeat the steps
above again.
If the power window automatic function
does not operate properly after performing
the procedure above, have your vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
NPA1478
Instruments and controls2-77