2019 HYUNDAI I10 warning

3-8
Safety system
Seatback angle
OAC3039003R
To recline the seatback:
1. Lean forward slightly and lift up the
seatback lever.
2. Carefully lean back on the seat
and adjust the seatback to the
position you desire.
3. Release the lever and make sure
the seatback is locked in place.
(The lever MUST return to its origi-
nal position for the seatback to
lock.)Reclining seatback
Sitting in a reclined position when the
vehicle is in motion can be danger-
ous. Even when buckled up, the pro-
tections of your restraint system (seat
belts and/or air bags) is greatly
reduced by reclining your seatback.
WARNING
NEVER ride with a reclined seat-
back when the vehicle is moving.
Riding with a reclined seatback
increases your chance of serious
or fatal injuries in the event of a
collision or sudden stop.
Drivers and passengers should
ALWAYS sit well back in their
seats, properly belted, and with
the seatbacks upright.
Seat belts must be snug against your
hips and chest to work properly.
When the seatback is reclined, the
shoulder belt cannot do its job
because it will not be snug against
your chest. Instead, it will be in front
of you.
During an accident, you could be
thrown into the seat belt, causing
neck or other injuries.
The more the seatback is reclined,
the greater chance the passenger’s
hips will slide under the lap belt or the
passenger’s neck will strike the shoul-
der belt.

3-10
Safety system
Rear seats (if equipped)
The rear seatbacks can be folded to
facilitate carrying long items or to
increase the luggage capacity of the
vehicle.
WARNING
‡Never allow passengers to sit on
top of the folded down seatback
whilst the vehicle is moving. This
is not a proper seating position
and no seat belts are available
for use. This could result in seri-
ous injury or death in case of an
accident or sudden stop.
‡Objects carried on the folded
down seatback should not
extend higher than the top of the
front seatbacks. This could allow
cargo to slide forward and cause
injury or damage during sudden
stops.1. Set the front seatback to the
upright position and if necessary,
slide the front seat forward.
2. Lower the rear head restraints to
the lowest position (if equipped
with adjustable head restraints).
OAI3039010
3. Insert the rear lap/shoulder belt
plate into the holder on the side
trim. It will prevent the lap/shoulder
belt from interfering with the seat-
back when folding.

3-11
03
OAC3039006TU
OAC3039007TU
4. Pull up the seatback lever and fold
the seatback toward the front of
the vehicle.
To use the rear seat, lift and push up
the seatback backward. Push the
seatback firmly until it clicks into
place. Make sure the seatback is
locked in place.
When returning the rear seatbacks to
the upright position, remember to
return the rear shoulder belts to their
proper position.
WARNING
When you return the rear seatback
to its upright position after being
folded down:
Be careful not to damage the seat
belt webbing or buckle. Do not
allow the seat belt webbing or
buckle to get caught or pinched in
the rear seat. Ensure that the seat-
back is completely locked into its
upright position by pushing on the
top of the seatback. Otherwise, in
an accident or sudden stop, the
seat could fold down and allow
cargo to enter the passenger com-
partment, which could result in
serious injury or death.
NOTICE
‡When returning the rear seat-
backs to the upright position,
remember to return the rear
shoulder belts to their proper
position.
‡Routing the seat belt webbing
through the rear seat belt guides
will help keep the seat belts from
being trapped behind or under
the seats.

3-12
Safety system
WARNING
Cargo
Cargo should always be secured
to prevent it from being thrown
about the vehicle in a collision and
causing injury to the vehicle occu-
pants. Do not place objects in the
rear seats, since they cannot be
properly secured and may hit the
front seat occupants in a collision.
WARNING
Cargo loading
Make sure the engine is off, the
Automated manual transmission
is in N (Neutral) or the Manual
transmission is in R (Reverse) or
1st, and the parking brake is
securely applied whenever loading
or unloading cargo. Failure to take
these steps may allow the vehicle
to move if the shift lever is inadver-
tently moved to another position.
Head restraint
The vehicle’s front and rear seats
have adjustable head restraints. The
head restraints provide comfort for
passengers, but more importantly
they are designed to help protect
passengers from whiplash and other
neck and spinal injuries during an
accident, especially in a rear impact
collision.
WARNING
To reduce the risk of serious injury
or death in an accident, take the
following precautions when adjust-
ing your head restraints:
‡Always properly adjust the head
restraints for all passengers
BEFORE starting the vehicle.

3-14
Safety system
OAC3039039R
Adjusting the height up and down
To raise the head restraint:
1. Pull it up to the desired position (1).
To lower the head restraint:
1. Push and hold the release button
(2) on the head restraint support.
2. Lower the head restraint to the
desired position (3).
NOTICE
OHI038136
If you recline the seatback towards
the front with the head restraint
and seat cushion raised, the head
restraint may come in contact with
the sunvisor or other parts of the
vehicle.
OAC3039041R
Removal/Reinstall
To remove the head restraint:
1. Recline the seatback (2) using the
seatback angle lever or switch (1).
2. Raise head restraint as far as it
can go.
3. Press the head restraint release
button (3) whilst pulling the head
restraint up (4).
WARNING
NEVER allow anyone to travel in a
seat with the head restraint
removed.

3-15
03
OAC3039040R
To reinstall the head restraint :
1. Recline the seatback.
2. Put the head restraint poles (2) into
the holes whilst pressing the
release button (1).
3. Adjust the head restraint to the
appropriate height.
4. Recline the seatback (4) using


seatback angle lever or switch (3).
WARNING
Always make sure the head
restraint locks into position after
reinstalling and adjusting it prop-
erly.
Rear seat head restraints
OAI3039007
* : 5 Seater
The rear seats are equipped with
head restraints in all the seating posi-
tions for the passenger’s safety and
comfort.
OAI3039008
Adjusting the height up and down
To raise the head restraint:
1. Pull it up to the desired position (1).
To lower the head restraint:
1. Push and hold the release button
(2) on the head restraint support.
2. Lower the head restraint to the
desired position (3).

3-16
Safety system
OAI3039009
Removal and installation
To remove the head restraint :
1. Raise it as far as it can go.
2. Press the release button (1) whilst
pulling upward (2).
To reinstall the head restraint :
1. Put the head restraint poles (3) into
the holes whilst pressing the
release button (1).
2. Adjust the head restraint to the
appropriate height.
Seat warmers (if equipped)
Seat warmers are provided to warm
the seats during cold weather.
WARNING
The seat warmers can cause a
SERIOUS BURN, even at low tem-
peratures and especially if used
for long periods of time.
Passengers must be able to feel if
the seat is becoming too warm so
they can turn it off, if needed.
People who cannot detect temper-
ature change or pain to the skin
should use extreme caution, espe-
cially the following types of pas-
sengers:
‡Infants, children, elderly or dis-
abled persons, or hospital outpa-
tients.
‡People with sensitive skin or
who burn easily.
‡Fatigued individuals.
‡Intoxicated individuals.
‡People taking medication that
can cause drowsiness or sleepi-
ness.

3-17
03
WARNING
NEVER place anything on the seat
that insulates against heat when
the seat warmer is in operation,
such as a blanket or seat cushion.
This may cause the seat warmer to
overheat, causing a burn or dam-
age to the seat.
NOTICE
To prevent damage to the seat
warmers and seats:
‡Never use a solvent such as
paint thinner, benzene, alcohol
or petrol to clean the seats.
‡Do not place heavy or sharp
objects on seats equipped with
seat warmers.
‡Do not change the seat cover. It
may damage the seat warmer or
air ventilation system.
OAC3039008TU
Whilst the engine is running, push
either of the switches to warm the
driver’s seat or front passenger’s
seat.
During mild weather or under condi-
tions where the operation of the seat
warmer is not needed, keep the
switches in the OFF position.
‡Each time you push the switch, the
temperature setting of the seat is
changed as follows:


OFFJHIGH ()JMIDDEL ()JLOW ()
K
‡The seat warmer defaults to the
OFF position whenever the ignition
switch is turned on.
‡When pressing the switch for more
than 1.5 seconds with the seat
warmer operating, the seat warmer
will turn OFF.