2019 HYUNDAI I10 ESP
[x] Cancel search: ESPPage 65 of 486
3-33
03
OOSEV038012
ISOFIX anchorages have been pro-
vided in the left and right outboard
rear seating positions. Their locations
are shown in the illustration. There
are no ISOFIX anchorages provided
for the centre rear seating position.
WARNING
Do not attempt to install a Child
Restraint System using ISOFIX
anchorages in the rear centre seat-
ing position. There are no ISOFIX
anchorages provided for this seat.
Using the outboard seat anchor-
ages, for the CRS installation on
the rear centre seating position,
can damage the anchorages.
OAC3039009TU
OAC3039010TU
[A] : ISOFIX Anchorage Position Indicator,
[B] : ISOFIX Anchorage
The ISOFIX anchorages symbols are
located on the left and right rear seat
cushions to identify the position of the
ISOFIX anchorages in your vehicle
(see arrows in illustration). Both rear
outboard seats are equipped with a
pair of ISOFIX anchorages as well as
a corresponding top-tether anchor-
age on the back side of the rear seats.
(Child Restraint Systems with univer-
sal approval according to ECE-R44
or ECE-R129 need to be fixed addi-
tionally with a top-tether connected to
the back side of the rear seats.)
ISOFIX anchorages are located
between the seatback and the seat
cushion of the rear seat left and right
outboard seating positions.
To use the ISOFIX anchorages, push
the upper portion of the ISOFIX
anchorage cover.
Page 79 of 486
3-47
03
WARNING
To reduce the risk of serious injury
or death from an inflating curtain
air bags, take the following pre-
cautions:
‡ All seat occupants must wear
seat belts at all times to help
keep occupants positioned prop-
erly.
‡ Properly secure child restraints
as far away from the door as pos-
sible.
‡ Do not place any objects over
the air bag. Also, do not attach
any objects around the area the
air bag inflates such as the door,
side door glass, front and rear
pillar, roof side rail.
‡ Do not hang other objects except
clothes, especially hard or break-
able objects. In an accident, it
may cause vehicle damage or
personal injury.
‡ Do not allow passengers to lean
their heads or bodies onto doors,
put their arms on the doors,
stretch their arms out of the win-
dow, or place objects between
the doors and seats.
‡ Do not open or repair the side
curtain air bags.
How does the air bags system
operate?
OAC3039023R
The SRS consists of the following
components:
(1) Driver’s front air bag module
(2) Passenger’s front air bag module*
(3) Side air bag modules*
(4) Curtain air bag modules*
(5) Retractor pre-tensioner assem-
blies*
(6) Air bag warning light
(7) SRS control module (SRSCM)/
Rollover sensor*
(8) Front impact sensors
(9) Side impact sensors*
(10) Side pressure sensors*
(11) Passenger’s front air bag OFF
indicator (front passenger’s seat
only) *
(12) Passenger’s front air bag ON/
OFF switch *
* : if equipped
The SRSCM continually monitors
SRS components whilst the ignition
switch is in the ON position to deter-
mine if a crash impact is severe
enough to require air bag deployment
or pre-tensioner seat belt deploy-
ment.
Page 80 of 486
3-48
Safety system
SRS warning light
The SRS (Supplement Restraint
System) air bag warning light on the
instrument panel displays the air bag
symbol depicted in the illustration.
The system checks the air bag elec-
trical system for malfunctions. The
light indicates that there is a potential
problem with your air bag system,
which could include your side and/or
curtain air bags used for rollover pro-
tection (if equipped with rollover sen-
sor).
WARNING
If your SRS malfunctions, the air
bag may not inflate properly dur-
ing an accident increasing the risk
of serious injury or death.
If any of the following conditions
occur, your SRS is malfunction-
ing:
‡ The light does not turn on for
approximately six seconds when
the ignition switch is in the ON
position.
‡ The light stays on after illuminat-
ing for approximately six sec-
onds.
‡ The light comes on whilst the
vehicle is in motion.
‡ The light blinks when the engine
is running.
We recommend that a HYUNDAI
authorised repairer inspect the
SRS as soon as possible if any of
these conditions occur.During a frontal collision, sensors will
detect the vehicle’s deceleration. If
the rate of deceleration is high
enough, the control unit will inflate the
front air bags, at the time and with the
force needed.
The front air bags help protect the
driver and front passenger by
responding to frontal impacts in which
seat belts alone cannot provide ade-
quate restraint. When needed, the
side air bags help provide protection
in the event of a side impact or roll-
over by supporting the side upper
body area.
‡ Air bags are activated (able to
inflate if necessary) only when the
ignition switch is in the ON position.
‡ Air bags inflate in the event of cer-
tain frontal or side collisions to help
protect the occupants from serious
physical injury.
‡ Generally, air bags are designed to
inflate based upon the severity of a
collision it’s direction etc. These
two factors determine whether the
sensors produce an electronic
deployment/inflation signal.
‡ The front air bags will completely
inflate and deflate in an instant. It is
virtually impossible for you to see
the air bags inflate during an acci-
dent. It is much more likely that you
will simply see the deflated air bags
hanging out of their storage com-
partments after the collision.
Page 81 of 486
3-49
03
‡ In addition to inflating in serious
side collisions, vehicles equipped
with a rollover sensor, side and/or
curtain air bags will inflate if the
sensing system detects a rollover.
When a rollover is detected, cur-
tain air bags will remain inflated
longer to help provide protection
from ejection, especially when
used in conjunction with the seat
belts. (if equipped with a rollover
sensor)
‡ To help provide protection, the air
bags must inflate rapidly. The speed
of air bag inflation is a consequence
of extremely short time in which to
inflate the air bag between the
occupant and the vehicle structures
before the occupant impacts those
structures. This speed of inflation
reduces the risk of serious or life-
threatening injuries and is thus a
necessary part of air bag design.
However, the rapid air bag inflation
can also cause injuries which can
include facial abrasions, bruises
and broken bones because the
inflation speed also causes the air
bags to expand with a great deal of
force.
‡ There are even circumstances
under which contact with the air
bag can cause fatal injuries, espe-
cially if the occupant is positioned
excessively close to the air bag.
You can take steps to reduce the risk
of being injured by an inflating air
bag. The greatest risk is sitting too
close to the air bag. An air bag needs
space to inflate. It is recommended
that drivers sit as far as possible
between the center of the steering
wheel and the chest whilst still main-
taining control of the vehicle.
OIK037081R
„Driver's front air bag (1)
When the SRSCM detects a suffi-
ciently severe impact to the front of
the vehicle, it will automatically deploy
the front air bags.
OIK037082R
„Driver's front air bag (2)
Upon deployment, tear seams mold-
ed directly into the pad covers will
separate under pressure from the
expansion of the air bags. Further
opening of the covers allows full infla-
tion of the air bags.
A fully inflated air bag, in combination
with a properly worn seat belt, slows
the driver’s or the front passenger’s
forward motion, reducing the risk of
head and chest injury.
Page 114 of 486
4-24
Instrument cluster
Low engine oil (if equipped)
This warning message is displayed
when the engine oil level should be
checked.
If this warning message is displayed,
check the engine oil level as soon as
possible and add engine oil as
required.
Slowly pour the recommended oil lit-
tle by little into a funnel. (Oil refill
capacity : approximately 0.15 ~ 0.26
gal. (0.6 ~ 1.0 l)
Use only the specified engine oil.
(Refer to "Recommended lubricants
and capacities" in chapter 8.)
Do not overfill the engine oil. Make
sure the oil level is not above F (Full)
mark on the dipstick.
NOTICE
If the message is displayed contin-
uously after adding the engine oil
and travelling approximately
50~100 km after the engine warms
up, we recommend that the system
be checked by a HYUNDAI autho-
rised repairer.
Engine has overheated
(if equipped)
This warning message is displayed
when the engine coolant temperature
is above 120°C (248°F). This means
that the engine is overheated and
may be damaged.
If your vehicle is overheated, refer
to “Overheating” in chapter 7.
Check headlight (if equipped)
This warning message is displayed if
the headlamps are not operating
properly.
In addition, if a specific lamp(turn sig-
nal lamp etc.) is not operating proper-
ly, the warning message according to
a specific lamp (turn signal lamp etc.)
is displayed. A corresponding bulb
may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same watt-
age rating.
Check brake light (if equipped)
This warning message is displayed if
the stop lamps are not operating
properly. A lamp may need to be
replaced.
Make sure to replace the burned out
bulb with a new one of the same watt-
age rating.
Page 171 of 486
5-43
05
NOTICE
If the driver exits the vehicle
through another door besides the
driver door, the battery saver func-
tion does not operate and the
headlight delay function does not
W X U Q 2 ) ) D X W R P D W L F D O O \
This may cause the battery to dis-
charge. To avoid battery dis-
F K D U J H W X U Q 2 ) ) W K H K H D G O L J K W V
manually from the headlight switch
before exiting the vehicle.
Daytime running light (DRL)
(if equipped)
The Daytime Running Lights (DRL)
can make it easier for others to see
the front of your vehicle during the
day, especially after dawn and before
sunset.
The DRL system will turn the dedi-
cated light OFF when:
1. The parking brake is applied.
2. The engine is turned off.
Headlight levelling device
OAC3059028R
7 R D G M X V W W K H K H D G O L J K W E H D P O H Y H O
according to the number of the pas-
sengers and loading weight in the
luggage area, turn the beam levelling
switch.
The higher the number on the switch
position, the lower the headlight
beam level. Always keep the head-
light beam at the proper levelling
position, or headlights may dazzle
other road users.
/ L V W H G E H O R Z D U H H [ D P S O H V R I D S S U R-
priate switch settings for varying
loads. For loading conditions other
W K D Q W K R V H O L V W H G D G M X V W W K H V Z L W F K
position to the most similar situation.
Loading conditionSwitch position
Driver only0
Driver + Front pas-
senger0
Full passengers
(including driver)1
Full passengers
(including driver) +
0 D [ L P X P S H U P L V V L E O H
loading2
' U L Y H U 0 D [ L P X P
permissible loading 3
Page 202 of 486
5-74
Convenient features
Automatic climate control
system
To defog inside windscreen
OAI3059108I
1. Select desired fan speed.
2. Select desired temperature.
3. Press the defroster button (
).
4. The air-conditioning will turn on
according to the detected ambient
temperature, outside (fresh) and
higher fan speed will be selected
automatically.
If the air-conditioning, outside (fresh)
air position and higher fan speed are
Q R W V H O H F W H G D X W R P D W L F D O O \ D G M X V W W K H
corresponding button or knob manu-
ally.
If the
position is selected, lower
I D Q V S H H G L V D G M X V W H G W R K L J K H U I D Q
speed.
To defrost outside windscreen
OAI3059109I
1. Set the fan speed to the highest
position.
6 H W W K H W H P S H U D W X U H W R W K H H [ W U H P H
hot (HI) position.
3. Press the defroster button (
).
4. The air-conditioning will turn on
according to the detected ambient
temperature and outside (fresh)
mode will be selected automatical-
ly.
If the position is selected, lower fan
V S H H G L V D G M X V W H G W R K L J K H U I D Q V S H H G
Page 240 of 486
![HYUNDAI I10 2019 Owners Manual 5-112
Convenient features
Restarting the current playback
On the control panel after the song
has played for 2 seconds, press the
[ 6 ( ( .] button.
‡ You can also push the Up lever on
the](/manual-img/35/56226/w960_56226-239.png "HYUNDAI I10 2019 Owners Manual 5-112
Convenient features
Restarting the current playback
On the control panel after the song
has played for 2 seconds, press the
[ 6 ( ( .] button.
‡ You can also push the Up lever on
the")
5-112
Convenient features
Restarting the current playback
On the control panel after the song
has played for 2 seconds, press the
[ 6 ( ( .] button.
‡ You can also push the Up lever on
the steering wheel.
Playing the previous or next
song
To play the previous song on the con-
trol panel within the first 2 seconds of
the current song, press the [ 6 ( ( .]
button. To play the next song, press
the [ 7 5 $ & . !] button on the control
panel.
‡ If more than 2 seconds of playback
have elapsed, press the [ 6 ( ( .]
button on the control panel twice to
play the previous song.
‡ You can also push the Up/down
lever on the steering wheel.
NOTICE
3 U H V V W K H > 0 ( 1 8 @ E X W W R Q R Q W K H
F R Q W U R O S D Q H O W R G L V S O D \ W K H P R G H
V H O H F W L R Q Z L Q G R Z W X U Q W K H > 7 8 1 ( @
N Q R E W R I L Q G W K H G H V L U H G V R Q J D Q G
S U H V V W K H N Q R E W R S O D \ W K H I L O H
Playing repeatedly
On the control panel, press the [ 5 3 7]
button. The repeat play mode changes
each time you press it. The corre-
sponding mode icon will be displayed
on the screen.
Playing in random order
On the control panel, press the
[ 6 + ) /] button. The shuffle play mode
is activated or deactivated each time
you press it. When you activate the
shuffle mode, the corresponding mode
icon will be displayed on the screen.
NOTICE
' H S H Q G L Q J R Q W K H F R Q Q H F W H G
% O X H W R R W K G H Y L F H R U P R E L O H S K R Q H
5 3 7 6 + ) / I H D W X U H V P D \ Q R W E H
V X S S R U W H G
Searching folders
1. On the control panel, press the
[ 0 ( 1 8 & / 2 & .] button.
2. When the option selection window
displays, turn the [TUNE] knob to
select the ) R O G H U O L V W and then
press the knob.
3. Navigate to the desired folder in
the ) R O G H U O L V W and then press the
[TUNE] knob.