2019 Hyundai Creta clock

7-81
7
Maintenance
Information
If the headlight aiming adjustment is
necessary after the headlight assembly
is reinstalled, consult an authorized
HYUNDAI dealer.
Headlight (Low/High) and static
bending light replacement
1. Open the hood.
2. Remove the headlight bulb cover
by turning it counterclockwise.
3. Disconnect the headlight bulb
socket-connector.
4. Unsnap the headlight bulb retain-
ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head-
light assembly.
i
(Continued)
Always handle them carefully,
and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact with liquids. Never
touch the glass with bare
hands. Residual oil may cause
the bulb to overheat and burst
when lit. A bulb should be
operated only when installed
in a headlight.
If a bulb becomes damaged or
cracked, replace it immediate-
ly and carefully dispose of it.
Wear eye protection when
changing a bulb. Allow the
bulb to cool down before han-
dling it.Halogen bulbs
Halogen bulbs contain pres-
surized gas that will produce
flying pieces of glass if bro-
ken.
(Continued)
WARNING
OLMB073042L
OGS075051
Static bending light
Turn signal
Low/High

7-82
Maintenance
6. Install a new headlight bulb and
snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket
connector.
8. Install the headlight bulb cover by
turning it clockwise.
Information
-
Bi-Function projection
headlamp
This headlamp is bi-function type that
switches the low beam to high or the
high beam to low using solenoid sys-
tem. So, the moving sound may be
heard when the headlamp switches
the low beam to high or the high beam
to low and it does not indicate mal-
function of the headlamp.
Turn signal light
1. Remove the turn signal light bulb
cover by turning it counterclock-
wise.
2. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb
cover by turning it clockwise.
Front fog light bulb replacement
1.Remove the under cover by rotat-
ing the screws and bolts.
2.Reach your hand into the back of
the front bumper.
3.Disconnect the power connector
from the socket.
4.Remove the bulb-socket from the
housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5.Install the new bulb-socket into the
housing by aligning the tabs on the
socket with the slots in the hous-
ing. Push the socket into the hous-
ing and turn the socket clockwise.
6.Connect the power connector to
the socket.
7.Reinstall the front bumper under
cover.
i

7-84
Maintenance
Outside light
1. Open the tailgate
2. Loosen the light assembly retain-
ing screws with a cross-tip screw-
driver.
3. Remove the rear combination light
assembly from the body of the
vehicle.4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
Inside lamp
Back-up light/Tail light
1. Turn off the engine.
2. Open the tailgate.
3. Remove the service cover using a
flat-blade screwdriver.
OGC074046
Turn signal Stop/TailTailBack upOGC074026
OGC074027
OGC074028
OGS078110L

7-85
7
Maintenance
4.Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5.Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
6.Insert a new bulb into the socket.
7.Install the socket into the assembly
by aligning the tabs on the socket
with the slots on the assembly and
turning the socket clockwise.Rear fog lamp (if equipped)
If the light does not operate, we rec-
ommend that the vehicle be checked
by an authorized HYUNDAI dealer.
High mounted stop light
If the light does not operate, we rec-
ommend that the vehicle be checked
by an authorized HYUNDAI dealer.
OGC074031

7-86
Maintenance
License plate light bulb
replacement
1.Remove the tailgate trim.
2.Remove the socket by turning it
counterclockwise.
3.Remove the bulb by pulling it
straight out.4.Install a new bulb.
5.Install the socket by turning it
clockwise.
6.Install the tailgate trim.
Interior light bulb replacement
OGS075057
OGS075058
■Map lamp (without sunroof)
■Map lamp (with sunroof)OGS075047
OGC074035

I-5
If the engine overheats ...................................................6-8
If the engine will not start ..............................................6-4
If the engine doesn't turn over or turns over ..............6-4
If the engine turns over normally but doesn't start ......6-4
If you have a flat tire ....................................................6-16
Changing tires ...........................................................6-17
Jack and tools ...........................................................6-16
Jack label ...................................................................6-21
Removing and storing the spare tire ..........................6-16
Ignition switch ................................................................5-5
Engine Start/Stop button ..............................................5-9
Key ignition switch......................................................5-5
In case of an emergency while driving ..........................6-3
If the engine stalls at a crossroad or crossing..............6-3
If the engine stalls while driving .................................6-3
If you have a flat tire while driving.............................6-3
Instrument cluster .........................................................3-43
Gauges .......................................................................3-45
Instrument Cluster Control ........................................3-44
LCD display ...............................................................3-67
Transaxle shift indicator ............................................3-48
Trip computer ............................................................3-74
Warning and indicator lights......................................3-50
Warning Messages (for Type B) ................................3-61Instrument panel overview (I) ........................................1-6
Instrument panel overview (II) .......................................1-7
Interior features...........................................................3-122
Ashtray .....................................................................3-123
Cargo area cover ......................................................3-129
Cigarette lighter .......................................................3-122
Clothes hanger .........................................................3-127
Cup holder ...............................................................3-124
Digital clock.............................................................3-122
Floor mat anchor(s) .................................................3-127
Luggage net holder ..................................................3-128
Power outlet/USB charger .......................................3-125
Sunvisor ...................................................................3-125
Interior overview (I) .......................................................1-4
Interior overview (II) ......................................................1-5
Jump starting...................................................................6-5
I
Index
I
J