2019 FIAT 500X automatic transmission fluid

STARTING THE
ENGINE
Before starting the engine, adjust the
seat, the interior rear view mirrors, the
door mirrors and fasten the seat belt
correctly.
Never press the accelerator pedal for
starting the engine.
If necessary, messages indicating the
starting procedure can be shown on
the display.
103) 104) 105) 106)
32) 33) 34) 35)
Versions with manual transmission
Proceed as follows:
engage the electric parking brake
and place the gear lever in neutral;
move the ignition device to MAR. On
Diesel versions, the
warning light on
the instrument panel turns on: wait for
the warning light to switch off;
fully depress the clutch pedal without
touching the accelerator;
turn the ignition device to AVV and
release it as soon as the engine starts;
if the engine does not start within
10 seconds, bring the ignition device
back to STOP and wait for
10-15 seconds before repeating the
starting procedure.
after the manoeuvre has been
repeated, if the problem persists,
contact a Fiat Dealership.
Versions with automatic
transmission
Proceed as follows:
engage the electric parking brake
and set the gear lever to P (Park) or N
(Neutral);
fully depress the brake pedal without
touching the accelerator;
set the ignition device to AVV;
if the engine does not start, bring
the ignition device back to STOP and
wait for 10-15 seconds before
repeating the starting procedure;
after the manoeuvre has been
repeated, if the problem persists,
contact a Fiat Dealership.
ENGINE STARTING
FAILURE
Starting the engine with electronic
key battery (Keyless Go) run down
or flat
If the ignition device does not respond
when the relevant button is pressed the
electronic key battery might be run
down or flat. Therefore, the system
does not detect the presence of the
electronic key on board the vehicle and
displays a dedicated message. In this
case, rest the rounded edge of the
electronic key (the side opposite themetal insert) on the ignition device and
press the button using the electronic
key. The ignition device is thus activated
and the engine can be started.
WARNING
103)Do not try to start the engine pouring
fuel or other flammable fluid inside the
throttle body air intake: this might damage
the engine and injury people nearby.
104)It is dangerous to run the engine in
enclosed areas. The engine takes in
oxygen and releases carbon dioxide,
carbon monoxide and other toxic gases.
105)The brake servo is not active until the
engine is started, so you would need to
apply much more force than usual to the
brake pedal.
106)Do not start the engine by pushing,
towing or driving downhill. These
manoeuvres may damage the catalytic
converter.
IMPORTANT
32)We recommend that during the initial
period, or during the first 1600 km, you do
not drive to full car performance (e.g.
excessive acceleration, long journeys at top
speed, sharp braking, etc.).
33)When the engine is switched off never
leave the ignition device in the MAR
position to prevent useless current
absorption from draining the battery.
114
STARTING AND DRIVING

Thousands of miles9 182736455463728190
Thousands of kilometres15 30 45 60 75 90 105 120 135 150
Years12345678910
Check windscreen and rear window wiper blade
position/wear●●●●●
Check operation of the windscreen wiper/washer system
and adjust jets, if necessary●●●●●
Check cleanliness of bonnet and luggage compartment
locks, cleanliness and lubrication of linkage●●●●●
Visually inspect conditions and wear of front and rear disc
brake pads and integrity of pad wear indicator●●●●●●●●●●
Visually inspect condition of the accessory drive belt(s)(3)●
Check tension of accessory drive belt (versions without
automatic tensioner)●●
Visual check of distribution command toothed belt
(1.4 Turbo Multi Air versions)(3)●
Check drive transmission idler unit (PTU) oil level
(4x4 versions)●●
Check rear differential fluid level (4x4 versions)●●
●
(3) The maximum mileage is 120,000 km. The belt must be replaced every 6 years, regardless of distance travelled. If the vehicle is used in heavy conditions (dusty
areas, cold climates, urban driving, long periods of idling), the maximum mileage is 60,000 km. The belt must be replaced every 4 years regardless of the
mileage.
(4) Check to be carried out every year for cars on the road in countries with particularly severe climates (cold countries).
181
Check oil level of electro-hydraulic actuator and top
up, if necessary (versions with dual-clutch automatic
transmission) (4)

Thousands of miles12 24 36 48 60 72 84 96 108 120
Thousands of kilometres20 40 60 80 100 120 140 160 180 200
Years12345678910
Check oil level of electro-hydraulic actuator and top up, if
necessary (1.6 Multijet versions with dual-clutch automatic
transmission)(5)
●
Check rear differential fluid level (2.0 Multijet 4x4 versions)●●
Change engine oil and replace oil filter(6)
Replace accessory drive belt/s(4)
Replace toothed timing drive belt (excluding 1.3 Multijet
16V versions)(4)
Replace fuel filter cartridge(7)
●●●
Replace air cleaner cartridge(8)●●●●●
Change the brake fluid(9)
(5) Check to be carried out every year for cars on the road in countries with particularly severe climates (cold countries).
(6) The actual interval for changing engine oil and replacing the engine oil filter depends on the vehicle usage conditions and is signalled by the warning light or
message in the instrument panel. In any case, it must never exceed 2 years. Where the car is used mostly in urban settings you need to replace the engine oil
filter every year. (4) The maximum mileage is 120,000 km. The belt must be replaced every 6 years, regardless of distance travelled. If the vehicle is used in heavy conditions (dusty
areas, cold climates, urban driving, long periods of idling), the maximum mileage is 60,000 km. The belt must be replaced every 4 years regardless of the
mileage.
(7) If the vehicle runs on fuel with quality below the relevant European specification, this filter must be replaced every 20,000 km
(8) If the vehicle is used in dusty areas, this cleaner must be replaced every 20,000 km.
(9) The brake fluid replacement has to be done every two years, irrespective of the mileage.
189

ENGINE OIL
168)
81)
Check the oil level a few minutes (about
5) after the engine has stopped, with
the vehicle parked on level ground.
Check that the oil level is between the
MIN and MAX lines on the dipstick A.
NOTE For 1.0 and 1.3 versions, the
dipstick A is integral with the cap B.
If the oil level is near or under the MIN
line, add oil through the filler B until it
reaches the MAX line.
Take out the engine oil dipstick A, clean
it with a lint-free cloth and reinsert it.
Extract it again and check that the level
is between the MIN and MAX marks on
the dipstick.
Engine oil consumption
82)
3)
The maximum engine oil consumption
is usually 400 grams every 1000 km.
When the car is new, the engine needs
to be run in; therefore the engine oil
consumption can only be considered
stabilised after the first 5000 - 6000 km.
IMPORTANT After adding or changing
the oil, let the engine turn over for a few
seconds and wait a few minutes after
turning it off before you check the level.
ENGINE COOLANT
169)
83)
If the level is too low, unscrew the cap
of reservoir C and add the fluid
described in the "Technical
Specifications" chapter.
WINDSCREEN/REAR
WINDOW WASHER FLUID
170) 171)
If the level is too low, lift reservoir cap D
and add the fluid described in the
chapter "Technical Specifications".
IMPORTANT The headlight washer
system (present) will not operate when
the fluid level is low, even though the
windscreen/rear window washer
continues to operate.
BRAKE FLUID
172) 173)
84)
Check that the fluid is at the max. level.
If the fluid level in the reservoir is too
low, undo reservoir cap E and add the
fluid described in the chapter "Technical
Specifications".
IMPORTANT Carefully clean the cap of
the reservoir and the surrounding
surface. Take great care to ensure that
impurities do not enter the reservoir
when the cap is opened.
For topping-up, always use a funnel
with integrated filter with mesh equal to
or lower than 0.12 mm.
IMPORTANT Brake fluid is hygroscopic
(i.e. it absorbs moisture). For this
reason, if the vehicle is mainly used in
areas with a high degree of
atmospheric humidity, the fluid should
be replaced at more frequent intervals
than specified in the "Scheduled
Servicing Plan".
AUTOMATIC
TRANSMISSION / TWIN
CLUTCH AUTOMATIC
TRANSMISSION
ACTUATION SYSTEM OIL
4)
The transmission control oil level should
only be checked at a Fiat Dealership.
200
SERVICING AND MAINTENANCE

EXHAUST SYSTEM
178) 179)
93)
Adequate maintenance of the engine
exhaust system represents the best
protection against leaks of carbon
monoxide into the passenger
compartment.
AUTOMATIC
TRANSMISSION
94)
Use only a gearbox fluid with the same
characteristics as those indicated in the
"Fluids and lubricants" table (see
"Technical specifications" chapter).
WARNING
177)The air intake system (air cleaner,
rubber hoses, etc.) can be a protection in
the case of blowbacks from the engine. DO
NOT REMOVE this system unless you
need to carry out repair or servicing
operations. Before starting the engine,
ensure that the system has not been
removed: failure to observe this precaution
may result in serious injury.178)Exhaust emissions are very
dangerous, and may be lethal. They
contain carbon monoxide, a colourless,
odourless gas which can cause fainting
and poisoning if inhaled.
179)The exhaust system may reach high
temperatures and may cause a fire if the
vehicle is parked on flammable material.
Dry grass or leaves can also catch fire if
they come into contact with the exhaust
system. Do not park or use the vehicle in a
place in which the exhaust system might
come into contact with flammable material.
IMPORTANT
87)It is recommended to have the vehicle
serviced by a Fiat Dealership. When
carrying out normal periodic operations and
minor maintenance interventions personally
on the car, it is recommended to use
suitable equipment, genuine spare parts
and the necessary fluids. Do not carry out
any interventions if you don't have the
necessary experience.
88)Incorrect maintenance of the car or
failure to carry out operations or repairs
(when necessary) may lead to more
expensive repairs, damage to other
components or have a negative impact on
car performance. Have any malfunction
inspected immediately by a Fiat Dealership.89)The vehicle is equipped with fluids
which are optimised or protecting its
performance and life and extending service
intervals. Do not use chemicals for washing
these components since they may damage
the engine, the transmission or the climate
control system. This damage is not covered
by the vehicle’s warranty. If any component
needs to be washed due to malfunctioning,
use only the specific liquid for that
procedure.
90)An excessive or insufficient amount of
oil inside the base is extremely damaging to
the engine. Make sure it is always at an
adequate level.
91)Always require the use of only
compressor coolants and lubricants
approved and suitable for the specific air
conditioning system fitted on the vehicle.
Some non-approved coolants are
flammable and may explode, with the risk
of injuries. The use of non-approved
coolants or lubricants may adversely affect
system efficiency, leading to expensive
repairs.
92)The air conditioner system contains
coolant under high pressure: to avoid
injuries to people or damage to the system,
any coolant addition or repair that requires
to disconnect the cables must be carried
out by a Fiat Dealership.
206
SERVICING AND MAINTENANCE

Weights (kg) 1.4 Turbo MultiAir(**) (°)1.4 Turbo MultiAir(**) (°°)1.4 Turbo MultiAir(**) (°°°)
Unladen weight (with all fluids,
fuel tank filled to 90% and
without optional equipment)1320 1320 1430
Payload including the driver
(*)555 / 540(**)555 / 540(**)670
Maximum permitted loads
(***)
– front axle 1050 1050 1150
– rear axle 900 900 1000
– total 1875 1875 2100
Towable loads
– braked trailer 1200 1200 1200
– trailer without brakes 600 600 600
Maximum load on tow hitch
(trailer with brakes)60 60 60
Maximum load on roof
(****)50 50 50
(°)
Versions
with
manual
transmission
(°°)
Manual
transmission
versions
with
dual
clutch
(°°°)
Versions
with
AT 9
automatic
transmission
(*)
If
special
equipment
is
fitted
(sunroof,
tow
hitch,
etc.)
the
unladen
car
weight
increases,
thus
reducing
the
specified
payload
in
relation
to
the
maximum
permissible
loads.
(**)
Version
for
specific
markets
(***)
Loads
not
to

be
exceeded.
The
user
is
responsible
for
arranging
goods
in
the
luggage
compartment
and/or
on
the
load
platform
within
the
maximum
permitted
loads.
(****)

With
carrier
rack
<000900a100a100a100a1000a0001002f0046005700460053000100460059004400460046004500010055004900460001004e00420059004a004e0056004e000100440050004e0043004a004f004600450001005700460049004a0044004d00460001004d00
5000420045000100570042004d00560046001b000100550049><00460001004e00420059004a004e0056004e000100550050005800420043004d00460001004d0050004200450001004a005400010050004f004d005a00010042004d004d00500058004600450001004a00470001004a005500010045005000460054000100
4f005000550001004600590044004600460045000100550049>F
NBYJNVN
DPNCJOFE
WFIJDMF

MPBE
222
TECHNICAL SPECIFICATIONS
.BYJNVN
DPNCJOFE
WFIJDMF
MPBE

WFIJDMF

USBJMFS
¡¡¡¡











Weights (kg) 1.6 MultiJet 2.0 Multijet
Versions without
AdBlue® (UREA)Versions with
AdBlue® (UREA)Versions without
AdBlue® (UREA)Versions with
AdBlue® (UREA)
Unladen weight (with all
fluids, fuel tank filled to
90% and without
optional equipment)1320
1410 / 1430
(°°)1495 1540
Payload including the
driver
(*)555 / 580(°°)510 605 510
Maximum permitted
loads
(***)
– front axle 1050 1050 1150 1150
– rear axle 900
900 / 950
(°°)1000 1000
– total
1875 / 1900
(°°)1920 / 1940(°°)2100 2050
Towable loads
– braked trailer
1200 / 900
(°°)


¡¡
1200 1200
– braked trailer 600 600 600 600
Maximum load on tow
hitch (trailer with brakes)60 60 60 60
Maximum load on
roof
(****)50 50 50 50
(°°)
Automatic
transmission
versions
with
dual
clutch
(*)
If
special
equipment
is
fitted
(sunroof,
tow
hitch,
etc.)
the
unladen
car
weight
increases,
thus
reducing
the
specified
payload
in
relation
to
the
maximum
permissible
loads.
(***)
Loads
not
to
be
exceeded.
The
user
should
carry
goods
in
the
luggage
compartment
and/on
load
carrying

platform
within
the
maximum
permitted
loads.
(****)

With
carrier
rack
<000900a100a100a100a1000a0001002f0046005700460053000100460059004400460046004500010055004900460001004e00420059004a004e0056004e000100440050004e0043004a004f004600450001005700460049004a0044004d00460001004d00
5000420045000100570042004d00560046001b000100550049><00460001004e00420059004a004e0056004e000100550050005800420043004d00460001004d0050004200450001004a005400010050004f004d005a00010042004d004d00500058004600450001004a00470001004a005500010045005000460054000100
4f005000550001004600590044004600460045000100550049>F
NBYJNVN
DPNCJOFE

WFIJDMF
MPBE
224
TECHNICAL SPECIFICATIONS.BYJNVN
DPNCJOFE

WFIJDMF
MPBE
WFIJDMF


USBJMFS
¡¡¡¡











¡¡




 

1.4 Turbo
MultiAir(**)
(°)1.4 Turbo
MultiAir(**)
(°°)1.4 Turbo
MultiAir(**)
(°°°)Prescribed fuels and original lubricants
Fuel tank (litres) 48 48 48
Unleaded petrol with RON no lower than 95
(EN228 specifications)
including a reserve of (litres) 5 - 7 5 - 7 5 - 7
Engine cooling system (litres) 5.2 5.2 5.2Mixture of distilled water and PARAFLU
UP
50%(*)
Engine sump (litres) 3.2 3.2 3.2 SELENIA DIGITEK P.E.
Engine sump and filter (litres) 3.6 3.6 3.6 SELENIA DIGITEK P.E.
Gearbox casing/differential (litres) 1.8 2.1 6.0TUTELA TRANSMISSION GEARFORCE (versions
with manual transmission/dual clutch automatic
transmission) / TUTELA TRANSMISSION AS8
(versions with AT9 automatic transmission)
Idler unit (PTU) (litres) – – 0.4 TUTELA TRANSMISSION B-5X
Rear differential (litres) – – 0.6 TUTELA TRANSMISSION COMPAQ DRIVE
Hydraulic brake circuit (kg) 0.83 0.83 0.83 TUTELA TOP 4/S
Windscreen and rear window
washer fluid reservoir (litres)2.5 2.5 2.5Mixture of water and PETRONAS DURANCE
SC35
(**) Version for specific markets (°) Versions with manual transmission
(°°) Versions with dual clutch automatic transmission
(°°°) Versions with AT9 automatic transmission
(*) When the vehicle is used in particularly harsh weather conditions, we recommend using a mixture of 60% PARAFLU
UPand 40% demineralised water.
226
TECHNICAL SPECIFICATIONS