2019 DODGE DURANGO tire pressure

5 PSI from the previous pressure check, have the tire inspected at once
by an authorized PAX System Retailer for PAX tires or a participating
Michelin tire retailer (or representative of your vehicle manufacturer if
your vehicle owner ’s manual so advises.) Failure to do so may cause
irreparable damage to the tire and result in sudden tire destruction and
personal injury.
TIRE PRESSURE MONITORING SYSTEMS (TPMS):
Your vehicle may be equipped with a Tire Pressure Monitoring System
(TPMS) that is designed to monitor the pressure of tires mounted on your
vehicle and sends a signal to the driver if a tire pressure falls below a
predetermined level. A TPMS should not replace monthly manual
pressure checks for all four (4) tires and the spare. We recommend that
you manually monitor and check tire pressure inflation with a pressure
gauge. Your tires should have the recommended pressure listed by your
vehicle’s manufacturer. This information can be found in the vehicle
owner ’s manual and often on a placard located in the vehicle’s door
jamb, inside the fuel hatch, or on the glove compartment door. If you
have a plus size fitment that requires a higher inflation pressure, your tire
pressure monitoring system will require re-calibration to new inflation
pressure. Refer to your tire dealer/installer of plus size tires for proper
inflation pressure.
We recommend checking air pressure once each month, and before a long
trip. Whether you have a full-sized or mini-spare, make sure that it is
properly inflated as well. If the TPMS generates improper monitoring or
signals we recommend that you consult your owner ’s manual provided
with your vehicle and follow-up with your vehicle’s manufacturer.
TIRE SPINNING
Do not spin wheels in excess of 35 mph (55 km/h) as indicated on the
speedometer. Excessive speed in a free-running, unloaded tire can cause
it to “explode” from centrifugal force. The energy released by such an
explosion is sufficient to cause serious physical injury or death. Never
allow anyone to stand near or behind the spinning tire.
When in mud, sand, snow, ice or other slippery conditions, do not engage
in excessive wheel spin. Accelerating the motor excessively, particularly
with automatic transmission vehicles, may cause a drive tire that has lost
traction to spin beyond its speed capability. This is also true when
balancing a drive tire/wheel assembly on the vehicle using the vehicle
engine to spin the tire/wheel assembly.
MICHELIN
171

HIGH SPEED DRIVING CAN BE DANGEROUS
Correct inflation pressure is especially important.However, at high
speeds, even with the correct inflation pressure, a road hazard, for
example is more difficult to avoid and if contact is made, has a greater
chance of causing tire damage than at a lower speed. Moreover, driving
at high speed reduces the reaction time available to avoid accidents and
bring your vehicle to a safe stop. If you see any damage to a tire or
wheel, replace it with the spare at once and visit a participating
Michelin Tire Retailer.
Exceeding the maximum speeds shown on the following page for each
type of MICHELIN® tire will cause the tire to build up excessive heat
which can cause tire damage that could result in sudden tire destruction
and rapid air loss. Failure to control a vehicle when one or more tires
experience a sudden air loss can lead to an accident.
In any case, you should not exceed reasonable speeds as indicated by
the legal limits and driving conditions.
SPEED RATINGS
Speed Symbols are shown on the sidewall of some MICHELIN® tires.
The following table shows the maximum speed corresponding to the
symbol.
*Some V (or VR) rated tires may have a speed capacity greater than
149 mph (240 km/h). Consult your participating Michelin® tire retailer
for maximum speed rating if your vehicle capability exceeds this speed.
**Z (or ZR) rated tires are designed to use on cars with maximum speed
capabilities in excess of 149 mph (240 km/h).
(W and Y speed ratings are subcategories of Z).
Consult your Michelin tire retailer for maximum speed capabilities. For
PAX® System Tires consult an authorized PAX System Tire Retailer.
Although a tire may be speed-rated, we do not endorse the operation of
any vehicle in an unsafe or unlawful manner. Speed ratings are based on
laboratory tests which relate to performance on the road, but are not
applicable if tires are underinflated, overloaded, worn out, damaged,
altered, improperly repaired or retreaded.
MICHELIN
172

Furthermore, a tire’s speed rating does not imply that vehicles can be
safely driven at the maximum speed for which the tire is rated,
particularly under adverse road and weather conditions or if the vehicle
has unusual characteristics.
Michelin® highway passenger tires that do not have a speed symbol on
the sidewall have a maximum speed rating of 105 mph (170 kph). Light
truck highway tires that do not have a speed symbol on the sidewall of
the tire have a maximum speed rating of 87 mph (140 kph).
MICHELIN® Winter tires that do not have a speed symbol on the
sidewall or tires with Q symbols have a speed rating of 100 mph
(160 km/h). Winter tires with a speed symbol have a maximum speed
rating in accordance with the symbol.
The speed and other ratings of retreaded tires are assigned by the
retreader and replace the original manufacturer ’s ratings.
IMPORTANT: In order to maintain the speed capability of the vehicle,
replacement tires must have speed ratings equal to or higher than those
fitted as original equipment (as indicated on the vehicle tire placard or
owner ’s manual). If tires with lower speed ratings are fitted, the vehicle’s
handling may be affected and the speed capability of the vehicle will be
lowered to the maximum speed capability of the replacement tires as
indicated in the following table.
REMEMBER...High speed driving can be dangerous and may damage
your tires.
AND...When driving at highway speeds, correct inflation pressure is
especially important.
MICHELIN
173

IMPACT DAMAGE
A tire impacted by a road hazard (curb, pothole, debris) may be damaged
but not have visible signs of damage on its surface. A tire damaged by an
impact may sustain a sudden failure a day, week, or even months later.
You may not recall hitting an object that damaged or injured your tires.
Air loss, unusual tire wear, localized wear or vibrations can also be signs
of internal tire damage.
If you suspect any damage to your tire or wheel from an impact with a
curb, pothole, debris on the road or any other road hazard, or if you feel
or hear any unusual vibration, replace with a properly inflated spare at
once and immediately visit any qualified tire technician.
INSPECTION
When inspecting your tires, including the spare, check the air pressures.
If the pressure check indicates that one of your tires has lost pressure of
two pounds or more, look for signs of penetration, valve leakage or wheel
damage that may account for the air loss.
Always look for bulges, cracks, cuts, penetrations, and abnormal tire
wear, particularly on the edges of the tire tread, which may be caused
by misalignment or underinflation. If any such damage is found, the
tire must be inspected by any Michelin tire retailer at once. Use of a
damaged tire could result in tire destruction.
All tires will wear out faster when subjected to high speeds as well as
hard cornering, rapid starts, sudden stops, frequent driving on roads
which are in poor condition, and off road use. Roads with holes and rocks
or other objects can damage tires and cause misalignment of your vehicle.
When driving on such roads, drive carefully and slowly, and before
driving again at normal or highway speeds, examine your tires for any
damage, such as cuts, bulges, penetrations, unusual wear patterns, etc.
WEAR BARS
MICHELIN® tires contain “Wear-Bars” in the grooves of the tire tread
which show up when only 2/32 nds of an inch (1.6 mm) of tread is
remaining. At this stage, your tires must be replaced. Tires worn beyond
this stage are extremely dangerous.
MICHELIN
175

DO NOT OVERLOAD - DRIVING ON ANY OVERLOADED TIRE IS
DANGEROUS
The maximum load rating of your tires is molded on the tire sidewall. Do
not exceed this rating. Follow the loading instructions of the manufac-
turer of your vehicle and this will ensure that your tires are not
overloaded. Tires which are loaded beyond their maximum allowable
loads for the particular application will build up excessive heat that may
result in sudden tire destruction.
Do not exceed the gross axle weight rating for any axle on your vehicle.
TRAILER TOWING
If you anticipate towing a trailer, you should visit any Michelin tire
retailer for advice concerning the correct size tire and pressures. Tire size
and pressures will depend upon the type and size of trailer and hitch
utilized, but in no case must the maximum cold inflation pressure or tire
load rating be exceeded. Check the tire decal and the owner ’s manual
supplied by the manufacturer of your vehicle for further recommenda-
tions on trailer towing.
MICHELIN® PAX® System Tires/Self-Supporting Zero Pressure (ZP)
Tires and Trailer Towing
Operation of Pax or ZP tires at low or zero air pressure with a trailer in
tow, is dangerous and is not recommended. If the low pressure warning
indicator is activated when a trailer is in tow, stop, disconnect the trailer,
and do not continue to tow the trailer until the tire has been repaired and
re-inflated to the proper air pressure. If the tire cannot be repaired, it must
be replaced with a new full size, PAX/ZP tire, and inflated to the proper
air pressure, before the trailer can be safely towed again.
WHEEL ALIGNMENT AND BALANCING ARE IMPORTANT FOR
SAFETY AND MAXIMUM MILEAGE FROM YOUR TIRES.
CHECK HOW YOUR TIRES ARE WEARING AT LEAST ONCE EACH
MONTH
If your tires are wearing unevenly, such as the inside shoulder of the tire
wearing faster than the rest of the tread, or if you detect excessive
vibration, your vehicle may be out of alignment or balance. These
conditions not only shorten the life of your tires but adversely affect the
handling characteristics of your vehicle, which could be dangerous. If
you detect irregular wear or vibration, have your alignment and balance
MICHELIN176

checked immediately. Tires which have been run underinflated will show
more wear on the shoulders than in the center of the tread.
TIRE MIXING
MICHELIN® tires are radial tires and for best performance it is recom-
mended that the same size and type of tire be used on all four wheel
positions. Before mixing tires of different types in any configuration on
any vehicle, be sure to check the vehicle manufacturer ’s owner‘s manual
for its recommendations.
It is especially important to check the vehicle manufacturer ’s owner ’s
manual when mixing, matching, or replacing tires on 4-wheel drive
vehicles, as this may require special precautions.
MICHELIN DOES NOT RECOMMEND MIXING PAX® SYSTEM TIRES
WITH NON-PAX TIRES / SELF-SUPPORTING ZERO PRESSURE (ZP)
TIRES WITH NON-ZP TIRES OTHER THAN THE TEMPORARY USE
OF THE SPARE IF THE VEHICLE IS SO EQUIPPED.
WINTER DRIVING
Tires which meet the Rubber Manufactures Association (RMA) definition
of snow tires are marked M/S, or M&S. On such tires, this designation is
molded into the sidewall. Tires without this notation are not recom-
mended or winter driving.While All-Season tires are designed to provide reliable
performance in some winter conditions, the use of four
(4) winter tires is recommended for optimal performance.
Tires designate for use in severe winter conditions are
marked on at leas one sidewall with the letter “M”
TIRE ROTATION AND REPLACEMENT
To obtain maximum tire wear, it may be necessary to rotate your tires.
Refer to your vehicle owner ’s manual for instructions on tire rotation. If
you do not have an owner‘s manual for your vehicle, Michelin recom-
mends rotating your tires every 6,000 to 8,000 miles (10,000 to 12,000 km).
Monthly inspection for tire wear is recommended. Your tires should be
rotated at the first sign of irregular wear, even if it occurs before 6,000
miles (10,000 km). This is true for all vehicles.
MICHELIN
177

When rotating tires with a directional tread pattern, observe the arrows
molded on the sidewall which show the direction the tire should turn.
Care must be taken to maintain the proper turning direction.
Some Tire Pressure Monitoring Systems (TPMS) may not recognize
that a tire has been moved to a different position on your vehicle. Make
certain that your TPMS system is reset, if necessary, so as to correctly
identify the location of each tire on your vehicle. Refer to your vehicle
owner ’s manual or your vehicle dealer.
Determine whether rotated tires require tire inflation adjustment as front
and rear position tire pressure may vary according to the vehicle
manufacturer ’s specification due to the actual load on that wheel
position. Some vehicles may have different sized tires mounted on the
front and rear axles, and these different sized tires have rotation
restrictions. Always check the vehicle owner ’s manual for the proper
rotation recommendations.
Full-size Spare
Full-size spare tires (not temporary spares) of the same size and construc-
tion should be used in a five (5) tire rotation. Always check the inflation
pressure of the full-size spare immediately before incorporating it into
rotation. Follow the vehicle manufacturer ’s recommended pattern for
rotation, or if not available, see a qualified tire technician.
Replacement of Two (2) Tires
It is recommended that all four (4) tires are replaced at the same time.
However, when only two tires are replaced, the new tires should be put
on the rear. The new tires, with deeper tread, may provide better grip and
water evacuation in wet driving conditions.
CUSTOMIZATION OF TIRES, WHEELS, OR SUSPENSION ON
SUVS AND LIGHT TRUCKS
Due to their size, weight and higher center of gravity, vehicles such as
SUVs and light trucks do not have the same handling characteristics as
automobiles. Because of these differing characteristics, failure to operate
your SUV/truck in a proper and safe manner can increase the likelihood
of vehicle rollover. Modifications to your SUV/truck tire size, tire type,
wheels or suspension can change its handling characteristics and further
increase the likelihood of vehicle rollover. Whether your SUV/truck has
the original equipment configuration for tires, wheels and suspension or
whether any of these items have been modified, always drive safely,
MICHELIN178

safety humps or ledges. As with any other tire air valve, the PAX®
System valve stem-pressure sensor combination must be in good
condition to assure its performance. Always utilize valve caps capable
of containing the tire’s air pressure, should the valve core leak. The
valve cap is the primary seal against air loss.
It is recommended that you have your tires and wheels balanced. Tires
and wheels which are not balanced may cause steering difficulties, a
bumpy ride, and irregular tire wear.
SPECIAL MOUNTING INSTRUCTIONS FOR PAX® SYSTEM
TIRES
PAX System wheels are different from all other wheels. Never attempt to
mount a non-PAX System tire on a PAX System wheel, or a PAX® System
tire on a non-PAX System wheel. Attempting to do so could cause serious
injury or death. All PAX System components (tire, wheel, support ring,
pressure sensor and gel) must be utilized. Never utilize a PAX System tire
and wheel without every other properly functioning component part,
correctly installed by an Authorized PAX System retailer. The PAX
System must be used on all wheel positions.
After a low or zero pressure driving event, the PAX System tire and wheel
may be hot to the touch.Always allow a PAX® System tire to cool
before attempting to handle it. Failure to do so could result in injury.
SPECIAL MOUNTING INSTRUCTIONS FOR SELF-SUPPORTING
ZERO PRESSURE™ (ZP) TIRES
ZP tires can be more difficult to mount than conventional tires. They
should be mounted and demounted only by a properly trained tire
professional. ZP tires can generate a tremendous amount of heat when
run at low or zero pressure. ALWAYS ALLOW A ZP TIRE TO COOL
BEFORE ATTEMPTING TO HANDLE IT. FAILURE TO DO SO COULD
RESULT IN INJURY.
MICHELIN® ZP tires are tubeless tires designed to operate in emergency
conditions at low or zero air pressure.
MICHELIN® SELF SUPPORTING Zero Pressure (ZP) TIRES AND
SPECIAL SH-M (SYMMETRIC HUMP-MODIFIED) WHEELS
Some MICHELIN® ZP tires can only perform with zero pressure
capability when mounted on special SH-M wheels. These tires bear the
SH-M designation immediately following the ZP designation on the
MICHELIN
181