2019 CHRYSLER PACIFICA HYBRID windshield wipers

▫Conversation Mirror .....................96
▫ Power Mirrors — If Equipped ..............97
▫ Outside Mirrors Folding Feature ............97
▫ Heated Mirrors — If Equipped .............97
▫ Power Folding Mirrors — If Equipped .........97
▫ Illuminated Vanity Mirrors — If Equipped .....98
 EXTERIOR LIGHTS .......................99
▫ Multifunction Lever ......................99
▫ Headlight Switch ........................99
▫ Daytime Running Lights — If Equipped ......100
▫ High/Low Beam Switch ..................100
▫ Automatic High Beam — If Equipped ........100
▫ Flash-To-Pass ........................ .101
▫ Automatic Headlights — If Equipped ........101
▫ Headlights On With Wipers — If Equipped . . . .101
▫ Headlight Delay — If Equipped ............101
▫ Lights-On Reminder ................... .102▫
Front Fog Lights — If Equipped ............102
▫ Turn Signals ......................... .102
▫ Lane Change Assist — If Equipped ..........103
▫ Battery Protection ..................... .103
 INTERIOR LIGHTS ..................... .103
▫ Courtesy/Interior Lighting ................103
 WINDSHIELD WIPER AND WASHERS ........106
▫ Windshield Wiper Operation ..............106
▫ Rain Sensing Wipers — If Equipped .........107
▫ Rear Wiper And Washer ..................108
 CLIMATE CONTROLS ................... .108
▫ Automatic

Climate Controls .............. .108
▫ Automatic Temperature Control (ATC) —
If Equipped ..........................115
▫ Operating Tips ....................... .122
 WINDOWS ........................... .124
▫ Power Windows ....................... .124
3
GETTING TO KNOW YOUR VEHICLE 15

2. Pull the multifunction lever toward you to switch theheadlights from the high beam to the low beam position.
3. Rotate the headlight switch counterclockwise from the AUTO to the on position.
NOTE: Once active, the Automatic High Beam system will
stop functioning below 12 mph (20 km/h).
Flash-To-Pass
You can signal another vehicle with your headlights by
lightly pulling the multifunction lever toward you. This
will cause the high beam headlights to turn on, and remain
on, until the lever is released.
Automatic Headlights — If Equipped
This system automatically turns your headlights on or off
based on ambient light levels. To turn the system on, turn
the headlight switch to the extreme clockwise position
aligning the indicator with the AUTO on the headlight
switch. When the system is on, the Headlight Time Delay
feature is also on. This means your headlights will stay on
for up to 90 seconds after you turn the ignition switch OFF.
To turn the Automatic System off, turn the headlight switch
counterclockwise to the O (off) position. NOTE:
The vehicle must be running before the headlights
will come on in the Automatic mode.
Headlights On With Wipers — If Equipped
When your headlights are in the AUTO mode and the
vehicle is running, the headlights will automatically turn
on when the wiper system is also turned on. Headlights on
when windshield wipers are on may be found on vehicles
equipped with an automatic headlight system.
NOTE: The Headlights with Wipers feature can be turned
on or off through the Uconnect system. Refer to “Uconnect
Settings” in “Multimedia” for further information.
Headlight Delay — If Equipped
This feature provides the safety of headlight illumination
for up to 90 seconds after exiting your vehicle.
To activate the delay feature, turn the ignition OFF while
the headlights are still on. The 90 second delay interval
begins when headlight switch is turned off. If the head-
lights or parking lights are turned back on or the ignition
switch is turned ON, the delay will be cancelled.
3
GETTING TO KNOW YOUR VEHICLE 101

WINDSHIELD WIPER AND WASHERS
Windshield Wiper Operation
The wipers and washers are operated by a switch within
the wiper lever. Rotate the end of the lever upward, to the
first detent past the intermittent settings for low-speed
wiper operation. Rotate the end of the lever upward to the
second detent past the intermittent settings for high-speed
wiper operation.NOTE:
Always remove any buildup of snow that prevents
the windshield wiper blades from returning to the off
position. If the windshield wiper switch is turned off and
the blades cannot return to the off position, damage to the
wiper motor may occur.
WARNING!
Sudden loss of visibility through the windshield could
lead to a collision. You might not see other vehicles or
other obstacles. To avoid sudden icing of the wind-
shield during freezing weather, warm the windshield
with the defroster before and during windshield
washer use.
Intermittent Wiper System
Use the intermittent wiper when weather conditions make
a single wiping cycle with a variable pause between cycles
desirable. Rotate the end of the wiper lever to the first
detent position, and then turn the end of the lever to select
the desired delay interval. There are four delay settings,
which allow you to regulate the wipe interval from a
minimum of one cycle every second to a maximum of
approximately 36 seconds between cycles. The delay inter-
vals will double in duration when the vehicle speed is
10 mph (16 km/h) or less.
Washer And Wiper Controls
106 GETTING TO KNOW YOUR VEHICLE

Windshield Washers
To use the washer, pull the lever rearward toward you and
hold while spray is desired. If the lever is pulled while on
the intermittent setting, the wipers will turn on and operate
for several wipe cycles after the lever is released, and then
resume the intermittent interval previously selected. If the
lever is pulled while the wipers are in the off position, the
wipers will operate several wipe cycles, then turn off.
Mist Feature
Use the Mist feature when weather conditions make occa-
sional usage of the wipers necessary. Push the lever upward
to the MIST position and release for a single wiping cycle.
NOTE:The mist feature does not activate the washer
pump; therefore, no washer fluid will be sprayed on the
windshield. The wash function must be used in order to
spray the windshield with washer fluid.
Rain Sensing Wipers — If Equipped
This feature senses rain or snowfall on the windshield and
automatically activates the wipers for the driver. This fea-
ture is especially useful for road splash or overspray from
the windshield washers of the vehicle ahead. Rotate the end
of the multifunction lever to one of the four intermittent
wiper sensitivity settings to activate this feature.
The sensitivity of the system is adjustable from the multi-
function lever. Wiper sensitivity position 3 has been cali-
brated for best overall wiping sensitivity. If the operator
desires more wiping sensitivity, they may select sensitivity
position 4. If the operator desires less wiping sensitivity, they
may select sensitivity positions 2 or 1. Place the multifunc-
tion lever in the OFF position when not using the system.
NOTE:
• The Rain Sensing feature will not operate when the
wiper speed is in the low or high position.
• The Rain Sensing feature may not function properly
when ice or dried saltwater is present on the windshield.
• Use of Rain-X or products containing wax or silicone
may reduce rain sensor performance.
• The Rain Sensing feature can be turned on and off
through the Uconnect System. Refer to “Uconnect Set-
tings” in “Multimedia” for further information.
The Rain Sensing system has protective features for the
wiper blades and arms. It will not operate under the
following conditions:
• Low Temperature Wipe Inhibit — The Rain Sensing
feature will not operate when the ignition is first
switched ON, when the vehicle is stationary and the
3
GETTING TO KNOW YOUR VEHICLE 107

outside temperature is below 32°F (0°C), unless the
wiper control on the multifunction lever is moved, the
vehicle speed becomes greater than 3 mph (5 km/h) or
the outside temperature rises above freezing.
• Neutral Wipe Inhibit — The Rain Sensing feature will
not operate when the ignition is ON, when the transmis-
sion gear selector is in the NEUTRAL position and the
vehicle speed is less than 3 mph (5 km/h), unless the
wiper control on the multifunction lever is moved, the
vehicle speed is greater than 3 mph (5 km/h) or the gear
selector is moved out of the NEUTRAL position.
• Remote Start Mode Inhibit — On vehicles equipped
with Remote Starting system, Rain Sensing wipers are
not operational when the vehicle is in the remote start
mode. Once the operator is in the vehicle and has placed
the ignition switch in the RUN position, rain sensing
wiper operation can resume, if it has been selected, and
no other inhibit conditions (mentioned previously) exist.
Rear Wiper And Washer
Rear Windshield Wiper Operation
Rotate the windshield wiper lever center ring upwards to
operate one of two modes for the rear window wiper:
• First detent — intermittent mode. •
Second detent — continuous mode.
Rear Windshield Washer Operation
Pushing the windshield wiper lever forward activates the
rear window washer. If the lever is pushed while on the
intermittent setting, the wipers will turn on and operate for
several wipe cycles after the lever is released, and then
resume the intermittent interval previously selected. If the
lever is pushed while the wipers are in the off position, the
wipers will operate several wipe cycles, then turn off.
CLIMATE CONTROLS
The Climate Control System allows you to regulate the
temperature, air flow, and direction of air circulating
throughout the vehicle. The controls are located on the
touchscreen (if equipped) and on the instrument panel below
the radio.
Automatic Climate Controls
The front controls are located on the touchscreen (if
equipped) and on the instrument panel below the radio. The
rear climate controls are located on the touchscreen and in
the rear headliner, on the passenger side of the vehicle.
NOTE: Heating and A/C are only available with the
vehicle running, unless the vehicle is plugged in.
108 GETTING TO KNOW YOUR VEHICLE

Rain Brake Support (RBS)
Rain Brake Support may improve braking performance in
wet conditions. It will periodically apply a small amount of
brake pressure to remove any water buildup on the front
brake rotors. It functions when the windshield wipers are
in LO or HI speed. When Rain Brake Support is active,
there is no notification to the driver and no driver interac-
tion is required.
Ready Alert Braking (RAB)
Ready Alert Braking may reduce the time required to reach
full braking during emergency braking situations. It antici-
pates when an emergency braking situation may occur by
monitoring how fast the throttle is released by the driver.
The EBC will prepare the brake system for a panic stop.
Regenerative Braking System (RBS) — Hybrid
Your vehicle has a Regenerative Braking System (RBS). The
RBS replenishes the vehicle’s high voltage battery during
deceleration, and is particularly useful in stop-and-go city
traffic. The electric motors which propel the vehicle for-
ward can operate as generators when braking. The RBS
recharges the high voltage battery under certain braking
conditions by recapturing energy that would otherwise belost while braking. The electric power that is generated
goes back into the high voltage battery for later use, for
example when acceleration is desired.
The RBS uses conventional hydraulic friction brakes, re-
generative braking, or a combination to slow the vehicle. If
the system detects slippery conditions while braking,
ONLY friction is used to slow the vehicle. The RBS can
result in extended life of the hydraulic service brakes;
however, all inspection, scheduled maintenance, and ser-
vice intervals for the vehicle service brakes must be fol-
lowed.
Audible Pedestrian Warning System
Your vehicle is equipped with an Audible Pedestrian
Warning System. The Audible Pedestrian Warning System
uses distinct sounds to alert pedestrians that your vehicle is
approaching. In addition, the module will indicate change
in speed by varying the pitch of sound.
The audible warning system uses an in-car sound synthe-
sizer with a speaker located in the underhood compart-
ment. The warning system is automatically activated when
selecting REVERSE, NEUTRAL, DRIVE or LOW.
202 SAFETY

11. Push the glove compartment door to the near closedposition to reengage the glove compartment travel
stops. Finally, pull the glove compartment tension
tether clip down and slide it back into the slot on the
side of the glove compartment door.
Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, door hinge pivot points and rollers, liftgate,
tailgate, decklid, sliding doors and hood hinges, should be
lubricated periodically with a lithium based grease, such as
Mopar Spray White Lube to assure quiet, easy operation
and to protect against rust and wear. Prior to the applica-
tion of any lubricant, the parts concerned should be wiped
clean to remove dust and grit; after lubricating excess oil
and grease should be removed. Particular attention should
also be given to hood latching components to ensure
proper function. When performing other underhood ser-
vices, the hood latch, release mechanism and safety catch
should be cleaned and lubricated.
The external lock cylinders should be lubricated twice a
year, preferably in the Fall and Spring. Apply a small
amount of a high quality lubricant, such as Mopar Lock
Cylinder Lubricant directly into the lock cylinder.
Windshield Wiper Blades
Clean the rubber edges of the wiper blades and the
windshield periodically with a sponge or soft cloth and a
mild nonabrasive cleaner. This will remove accumulations
of salt or road film.
Operation of the wipers on dry glass for long periods may
cause deterioration of the wiper blades. Always use washer
fluid when using the wipers to remove salt or dirt from a
dry windshield.
Avoid using the wiper blades to remove frost or ice from
the windshield. Keep the blade rubber out of contact with
petroleum products such as engine oil, gasoline, etc.
NOTE: Life expectancy of wiper blades varies depending
on geographical area and frequency of use. Poor perfor-
mance of blades may be present with chattering, marks,
water lines or wet spots. If any of these conditions are
present, clean the wiper blades or replace as necessary.
The wiper blades and wiper arms should be inspected
periodically, not just when wiper performance problems
are experienced. This inspection should include the follow-
ing points:
• Wear or uneven edges
• Foreign material
8
SERVICING AND MAINTENANCE 457

Daytime Brightness, Interior Lights..............105
Daytime Running Lights .................. .99, 100
Dealer Service ............................ .450
Defroster, Windshield ....................... .279
Delay (Intermittent) Wipers ...................106
Diagnostic System, Onboard ...................190
Dimmer Switch Headlight ...............................99
Dipsticks Oil (Engine) ........................... .448
Disabled Vehicle Towing .................... .438
Disposal Antifreeze (Engine Coolant) .................467
Do Not Disturb ........................... .590
Door Ajar ............................... .182
Door Ajar Light ........................... .182
Drag And Drop Menu ...................... .515
Driver ’s Seat Back Tilt ........................69
Driving Through Flowing, Rising, Or Shallow Standing
Water ................................ .389
DVD Player (Video Entertainment System) .........545
Electric Brake Control System ..................195
Anti-Lock Brake System ................... .194Traction Control System
................... .195
Electric Parking Brake ...................... .293
Electric Remote Mirrors .......................97
Electronic Speed Control (Cruise Control) .........306
Electronic Stability Control (ESC) ...............197
Electronic Throttle Control Warning Light .........180
Emergency, In Case Of Hazard Warning Flasher ...................392
Jacking ........................ .412, 413, 472
Jump Starting .......................... .431
Overheating ........................... .436
Towing ............................... .438
Emission Control System Maintenance ............191
Engine Air Cleaner ............................ .452
Break-In Recommendations .................293
Checking

Oil Level ...................... .448
Compartment .......................... .447
Compartment Identification .................447
Coolant (Antifreeze) ..................... .509
Cooling .............................. .463
Exhaust Gas Caution .................. .278, 507
Fuel Requirements ....................... .504
Oil ........................... .450, 508, 509
Oil Filter .............................. .451
12
INDEX 605