2019 CHEVROLET LOW CAB FORWARD warning light

Chevrolet Low Cab Forward 5.2L Diesel Engine 4500/5500 Series (GMNA-
Localizing-U.S.-12407814) - 2019 - crc - 12/13/17
Driving and Operating 175
4. Press the cruise control mainswitch to set it to ON. At this
time, the operation indicating
light will turn to green.
5. Turn and hold the cruise control set switch in the SET
position. After approximately
3 seconds the cruise control
set indicator light will begin to
flash slowly and the engine idle
will increase to 1,200 r/min.
Canceling High Idle Mode
Any of the following actions will
cancel high idle mode.
. The cruise control main switch is
set to OFF.
. The brake pedal is pressed.
. The parking brake is released.
. The selector lever is moved from
P (Park) or N (Neutral) position.
. The accelerator pedal is
pressed, accelerating the engine
beyond the engine speed
threshold. The cruise set indicator light will
stop flashing and the engine speed
will return to normal.
Engine Checks Before
Operating
Checks Before Operating
Allow the engine to warm up before
placing the engine under heavy load
driving. While the engine is warming
up under light load, the following
checks should be made:
1. Observe the red engine oil pressure warning light. The
light should go out when the
engine is running. If it stays on,
shut the engine off and find the
cause.
2. Look at the engine coolant temperature gauge. If the
gauge reaches the H (HOT)
area, stop the engine and find
the cause of the overheating.
3. Check that the battery warning light has gone out. The light
should go off and stay off at
normal idle speeds. If the light does not go out or comes on
during normal operation, have
the charging system checked.
4. Check that the brake low vacuum warning light is out
and that the vacuum buzzer is
not sounding. It is normal for
the warning buzzer to sound
for a few seconds after the
engine starts. If the light and
buzzer remain on, do not drive
the vehicle until the cause has
been found and corrected.
5. Look at the brake system warning light. It should be out
when the parking brake is
released and the engine is
running. If it stays on, it could
mean that the brake fluid level
is low. Check the brake fluid
reservoir. This condition must
be corrected before moving the
vehicle.

Chevrolet Low Cab Forward 5.2L Diesel Engine 4500/5500 Series (GMNA-
Localizing-U.S.-12407814) - 2019 - crc - 12/13/17
180 Driving and Operating
Diesel Particulate
Filter
Diesel Particulate Filter (DPF)
The DPF purifies diesel exhaust
gases of particulate matter (PM). PM
is filtered from the exhaust gas and
collected in the DPF. When PM is
collected to the predetermined level
by the engine control module, the
DPF automatically burns the PM in
a process called regeneration.
Regeneration may not be completed
under certain driving conditions.
If this occurs, the Driver Information
Center (DIC) will provide prompts to
properly complete DPF
regeneration.
The following sections will provide
details on DPF regeneration. Follow
the steps carefully to keep the DPF
in good working order. SeeDriver
Information Center (DIC) 082,
Recommended Fluids and
Lubricants 0349, and Engine Oil
0 245.
{Warning
Exhaust parts and gases become
very hot when the DPF is being
regenerated.
Parking over flammable items
could allow them to touch hot
exhaust parts under your vehicle
and cause them to ignite. Do not
park over papers, leaves, grass
or other things that can burn. You
and others could be seriously
injured.
This content is to restore the
function of the DPF and it is not a
malfunction. However, the check
engine malfunction indicator light
and reduced engine power indicator
light may come on and the power
output may be limited if driving or
power take-off (PTO) operation is
continued for a long time with the
regeneration required warning light
or selectable (switch) regeneration
required warning light (amber/
red) on. This is to prevent the DPF from
being damaged. When operating
PTO during parking, check to
ensure that the regeneration
required warning light or selectable
(switch) regeneration required
warning light (amber/red) on the DIC
is not on.
Engine oil that supports DPF (low
ash oil) is recommended. Use of low
ash oil extends the maintenance
interval of the DPF filter.
Do not modify the DPF or exhaust
pipe. Changing the alignment,
length or diameter of the exhaust
pipe would adversely affect the
exhaust system's exhaust emission
reduction function. If any
modification is necessary to install a
component to the rear of the
vehicle, consult your dealer.
Although the DPF filter automatically
undergoes regeneration (burning of
the accumulated PM) when a
certain amount of PM has
accumulated, driving conditions can
prevent completion of regeneration.

Chevrolet Low Cab Forward 5.2L Diesel Engine 4500/5500 Series (GMNA-
Localizing-U.S.-12407814) - 2019 - crc - 12/13/17
Driving and Operating 181
The selectable (switch) regeneration
required warning light (amber) will
turn on when regeneration cannot
be completed automatically. Perform
Running or Switch regeneration in
accordance with the proper
procedure. This is to restore DPF
function and is normal.
The exhaust pipe mixes air with the
exhaust gas to lower its temperature
before it leaves the exhaust pipe.
The frequency of regeneration
increases especially under the
following environments:
‐Midwinter.
‐ Continuous low-speed driving for
long hours (The frequency of
regeneration increases
particularly with special
equipment vehicles such as
sweeper vehicles which mainly
travel at low speed. The
frequency of regeneration is
higher as compared to delivery
vehicles which mainly travel at
standard high speed). Automatic regeneration is performed
under normal driving conditions
(DPF soot accumulation status level
5, and in rare cases, may be
performed at continuously
low-speeds for long hours, except
PM level 5); however, the
regeneration required warning light
(amber) may be displayed in the
DIC under the following driving
conditions:
‐
When only low-speed driving at/
under vehicle speed of 15 km/h
(9 MPH) is performed.
‐ When frequent engine start and
stop are performed.
‐ When the engine stops every
time before the engine is
warmed up.
‐ When continuous idling (over
1 hour) is frequently performed.
If the vehicle is stationary with the
engine idling during DPF
regeneration, the exhaust brake or
exhaust throttle operates. Operating
sounds will be heard when the exhaust brake or exhaust throttle is
activated or deactivated. The
sounds do not indicate a fault.
White smoke could be emitted
briefly from the exhaust pipe in the
following situations, but it is not
indicating a fault.
‐
Combustion of PM during DPF
regeneration.
‐ During DPF regeneration of a
new vehicle which has been
driven a certain distance. The
vehicle may not emit white
smoke during its initial operation
when new.
‐ Long continuous idling.
The exhaust brake may
automatically be activated in order
to prevent emission of white smoke
if the engine idles continuously over
an extended period of time.
White smoke may be produced
during switch regeneration; do not
perform switch regeneration in any
poorly ventilated indoor place.

Chevrolet Low Cab Forward 5.2L Diesel Engine 4500/5500 Series (GMNA-
Localizing-U.S.-12407814) - 2019 - crc - 12/13/17
182 Driving and Operating
White smoke may be produced
during DPF regeneration when a
new vehicle has been driven a
certain distance, but this is not a
malfunction. The vehicle may not
emit white smoke immediately after
purchase.
DPF PM Accumulation Level
This green display only indicates
DPF soot accumulation status. The
DIC can display the PM
accumulation level in green. The L
indicates Low accumulation of PM
and the H indicates High
accumulation of PM in the DPF.
As PM accumulation increases
inside the DPF, the DIC will display
additional bars increasing from L to
H to show the approximate level of
PM accumulation. SeeDriver
Information Center (DIC) 082. DPF Regeneration Status
This amber display indicates the
DPF is regenerating. During DPF
regeneration, the DIC can display
the status of PM reduction in amber.
The highest accumulation level bar
will be flashing as indication of the
regeneration process.
As PM levels decrease in the DPF
during the regeneration process, the
DIC will decrease the number of
bars from H to L. See
Driver
Information Center (DIC) 082.
Automatic Regeneration of DPF
The DPF will regenerate itself as
part of normal operation.
The engine control module (ECM)
controls this function based on
several factors including hours of
operation and mileage. When
automatic regeneration starts, the
regeneration in progress indicator
light (amber) is displayed on
the DIC.
During regeneration the engine idle
speed will increase and the exhaust
brake may activate when the vehicle
is idling while stopped or parked.
Regeneration is normally completed
in about 20 minutes. See Driver
Information Center (DIC) 082.
{Warning
To prevent fire, ensure that there
is no combustible material near
the muffler, the DPF or the
exhaust pipe. Also, be careful not
to burn yourself on the hot
exhaust gas. You and others
could be seriously injured.

Chevrolet Low Cab Forward 5.2L Diesel Engine 4500/5500 Series (GMNA-
Localizing-U.S.-12407814) - 2019 - crc - 12/13/17
Driving and Operating 183
The DPF performs regeneration
automatically when a certain
quantity of PM accumulates in the
filter.
Depending upon running conditions,
however, the regeneration may
sometimes not be completed. In this
case, the regeneration required
warning light (amber) will come on,
so promptly operate the emergency
regeneration according to the
Emergency Regeneration
Procedure. This operation recovers
the function of the DPF. It does not
mean that a breakdown has
occurred.
The engine speed may increase
and the exhaust brake may activate
while the vehicle is stopped with the
engine idling. When this occurs, the
DPF is automatically regenerated.
This does not indicate a failure.
The system generates a sound
during the automatic regeneration
and its cancellation. This does not
indicate a failure.DPF SwitchThe DPF switch is used to burn PM
(regenerate the filter). You can
initiate regeneration when the
regeneration required warning light
or selectable (switch) regeneration
required warning light turns on with
short repeated beeps.
Continuing driving without
performing the regeneration will
cause the check engine malfunction
indicator light and reduced engine
power indicator light to come on.
The DPF then must be repaired at
the nearest dealer.
Emergency Regeneration
Procedure
If the regeneration required warning
light (amber) or selectable (switch)
regeneration required warning light
(amber) turns on the DIC, the DPF
could not satisfactorily complete
automatic regeneration and driver
action is required. If the
regeneration required warning light
(Not selectable (switch)
regeneration warning light) is turned
on, you can choose from Running

Chevrolet Low Cab Forward 5.2L Diesel Engine 4500/5500 Series (GMNA-
Localizing-U.S.-12407814) - 2019 - crc - 12/13/17
184 Driving and Operating
regeneration or Switch regeneration
in order to complete the DPF
regeneration.
If the selectable (switch)
regeneration required warning light
turns on, you have to perform
Switch regeneration in order to
complete the DPF regeneration.
If you continue driving too long with
the regeneration required warning
light (amber) or selectable (switch)
regeneration required warning light
(amber) displayed on the DIC
without performing one of the
possible regenerations, the
message will change to red
Regeneration Required warning
light or selectable (switch)
regeneration required warning light.
The red regeneration required
warning light or selectable (switch)
regeneration required warning light
indicates the DPF filter is nearly full
of PM, a condition which may be
damaging to the filter.
DPF regeneration should be
completed immediately if the red
regeneration required warning lightor selectable (switch) regeneration
required warning light is displayed
on the DIC.
Continuing to drive without
performing DPF regeneration will
cause the check engine malfunction
indicator light and reduced engine
power indicator light to come on, an
engine power reduction, and may
cause damage to the DPF filter. See
Driver Information Center (DIC)
0
82.
Running Regeneration Procedure
Use this option for completing DPF
regeneration, if driving conditions
and traffic allow you to maintain a
relatively constant speed above
48 km/h (30 MPH) for about
20 minutes.
Follow the steps below to use
Running regeneration: 1. Determine if road and traffic conditions allow for relatively
constant speeds above
48 km/h (30 MPH). 2. Increase the vehicle speed
above 48 km/h (30 MPH) and
keep a constant speed.
3. When vehicle speed, engine coolant temperature and other
factors are met the engine
control module (ECM) will
begin DPF regeneration and
the regeneration in progress
indicator light (amber) will
appear on the DIC.
4. Continue driving until the regeneration in progress
indicator light (amber) goes off.
When this indicator light goes
off the DPF regeneration is
complete.
See Driver Information Center (DIC)
0 82.
While the vehicle is at a stop with
engine idling, the engine speed
increases.

Chevrolet Low Cab Forward 5.2L Diesel Engine 4500/5500 Series (GMNA-
Localizing-U.S.-12407814) - 2019 - crc - 12/13/17
Driving and Operating 185
Switch Regeneration Procedure
{Warning
To prevent a fire, make sure that
there is no flammable material
near the muffler, DPF and(Continued)
Warning (Continued)
exhaust pipe. Remember that the
temperature of exhaust gases is
high enough to burn you. You and
others could be seriously injured.
Select Switch regeneration
procedure if the Running
regeneration procedure is not
possible, or if the selectable (switch)
regeneration required warning light
(amber or red) is displayed on
the DIC. 1. Stop the vehicle at a safe place free of flammable material such
as dead grass, leaves or waste
paper.
2. Move the selector lever into the P position and firmly engage
the parking brake.
3. Let the engine idle. Be sure the accelerator pedal is not
pressed and the PTO switch (if
equipped) is OFF.
4. Press and release the DPF switch. 5. The regeneration required
warning light (amber or red) or
selectable (switch)
regeneration required warning
light (amber or red) on the DIC
will turn off and the
regeneration in progress
indicator light will appear.
6. Do not leave the vehicle during the regeneration. Regeneration
normally completes in about
20 minutes.
7. When the regeneration in progress indicator light (amber)
goes out, regeneration is
completed. Normal driving is
then possible.
If the Switch regeneration is
interrupted, a selectable (switch)
regeneration required warning light
(amber) will appear on the DIC. You
must complete the DPF
regeneration by performing the
Switch regeneration once again as
soon as possible.
If you continue driving too long with
the selectable (switch) regeneration
required warning light (amber)

Chevrolet Low Cab Forward 5.2L Diesel Engine 4500/5500 Series (GMNA-
Localizing-U.S.-12407814) - 2019 - crc - 12/13/17
186 Driving and Operating
displayed on the DIC, the message
will change to red. The selectable
(switch) regeneration required
warning light (red) indicates the
DPF filter is nearly full of PM, a
condition which may be damaging
to the filter.
DPF regeneration should be
completed immediately if the
selectable (switch) regeneration
required warning light (red) is
displayed on the DIC.
Continued driving without
performing DPF regeneration will
cause the check engine malfunction
indicator light and reduced engine
power indicator light to come on, an
engine power reduction, and may
cause damage to the DPF filter. See
Driver Information Center (DIC)
082.
When operating the PTO for a long
time if your vehicle is so equipped,
make sure that the regeneration
required warning light or selectable
(switch) regeneration required
warning light (amber) is not
turning on. Once the Switch regeneration is
started, it cannot be switched to the
Running regeneration if interrupted.
When the Switch regeneration is
selected, end regeneration in a
single operation if possible.
During the regeneration, the engine
speed may vary, causing the
exhaust brake valve to be
deactivated. However, while the
regeneration in progress indicator
light (amber) appears, regeneration
is still taking place, so continue to
perform regeneration until the
message goes off.
The time needed to complete
regeneration differs depending on
the outside temperature.
The exhaust brake or exhaust
throttle is activated during DPF
regeneration. The exhaust brake or
exhaust throttle starting to operate
or being disengaged will produce a
sound, but this does not indicate a
failure.
During regeneration, white smoke
may be temporarily produced from
the exhaust pipe. This results from
combustion of PM, it does not
indicate a failure.
Switch regeneration will complete
earlier immediately after driving than
when the engine is cold.
The engine coolant temperature
may rise during switch regeneration.
Interruption of Switch
Regeneration
If you must interrupt regeneration for
an unavoidable reason, press the
DPF switch again.
The regeneration in progress
indicator light (amber) changes to
the selectable (switch) regeneration
required warning light (amber).
Then, you can drive the vehicle.
If you interrupt regeneration, you
need to perform regeneration again.
Perform switch regeneration
beginning with Step 1 as soon as
possible.