2019 Alfa Romeo Giulia light

Versions - 2.0 T4 MAir engine right-hand drive, fig. 152
1. Engine oil filler 2. Brake fluid reservoir cap access cover 3. Primary engine cooling reservoir plug 4. Windscreen/headlights
washer fluid reservoir cap 5. Secondary engine cooling reservoir plug
15209026S0006EM
168
SERVICING AND CARE

Diesel versions - 2.2 JTD engine,fig. 153
1. Engine oil filler 2. Engine coolant reservoir cap 3. Brake fluid reservoir cap access cover 4. Windscreen/headlights washer
fluid reservoir cap 5. Secondary engine cooling reservoir plug
15309026S0503EM
169

ENGINE OIL
158)66)
IMPORTANT
It
is
advisable
to
check
the

oil
level
indication
before
long
journeys.
The
engine
oil
level
can
be
seen
on
the

instrument
panel
display
every
time
the

engine
is
started,
or
on
the
Connect

system
display
by
activating
on
the
main

menu
(MENU
button)
the
following

functions
in
sequence:
“Apps”;
“Car

Status”
and
“Oil
Level”.
Check
on
the
display
using
the
6
notches

that
the
oil
level
is
between
MIN
and

MAX
level:
1
notch
MIN
level,
6
notches

MAX
level.
If
the
oil
level
indication

reaches
the
first
red
mark,
add
oil

through
the
filler
1,
considering
that
each

notch
shown
on
the
display
corresponds

to
approximately:
2.0
T4
MAir
engine
0.055
UK
gal

(250
ml).
2.2
JTD
Engine







Õ
c
Õ
Ú
Ø

ƒ}ˆ
¦
×
Õ
Õ
‰ˆ
¡
c







‚

‹ŽŽ


67)
IMPORTANT
Make
sure
not
to
add
too

much
engine
oil
when
topping
up.
Engine

oil
in
excess
may
damage
the
engine.

Have
the
car
checked.
Never
exceed
the

MAX
level
when
topping
up
engine
oil.
It
is advisable to check the oil level in
intermediate steps on the display.
IMPORTANT The oil level is not refreshed
immediately on the display after topping
up. Consequently, wait for the oil level to
be refreshed on the display following to
procedure shown below.
Top-up and oil level indication update
on display
If a top-up is needed, proceed as follows
to ensure correct indication of the oil
level on the display:
2.0 T4 MAir engine
with the vehicle level, run the engine
for approximately 5 minutes
(temperature higher than 176°F (80°C)
and then stop the engine;
start the engine again and idle it for
about 2 minutes.
2.2 JTD Engine
with the car level, run the engine until
the second oil temperature notch lights
up on the display on the instrument panel,
then stop the engine;
wait for at least 3 minutes, turn the
ignition switch to ON without starting the
engine and wait for 20 seconds.
IMPORTANT If the indication is not
correct after the procedure, contact an
Alfa Romeo Dealership.IMPORTANT The oil dipstick in the engine
compartment, on versions with 2.2 JTD
engine, must be used ONLY if the oil level
sensor is faulty. The latter condition is
indicated by the
symbol which will
appear on the instrument panel.
The manual engine oil level checking
procedure must be carried out, when
necessary, on a cold engine only.
Never attempt to carry out the manual
engine oil checking procedure (using the
dipstick) with the engine hot. Contact
with the surrounding hot engine parts
could cause burns.
This operation is permitted only for the
time actually needed to restore correct
operation of the oil level sensor at an Alfa
Romeo dealership.
Engine oil consumption
68)
4)
The maximum engine oil consumption is
usually 0.88 lb (400 grams every
620 miles (1000 km). When the car is
new, the engine needs to be run in,
therefore the engine oil consumption can
only be considered stabilised after the
first 3100 - 3700 miles (5000 -
6000 km).
170
SERVICING AND CARE

ENGINE COOLANT FLUID
159)
69)
If the level is too low, unscrew the
reservoir cap and add the fluid described
in the "Technical Specifications" chapter.
On the 2.0 T4 MAir engine version with
right-hand drive, remove the shield 6
fig. 154 to check the fluid level in the
primary reservoir. To do this, release the
fixing clip 7 and lift upwards.
WASHER FLUID FOR WINDSCREEN/
HEADLIGHTS
160) 161)
The windscreen and headlights washer
fluid reservoir (where provided) is
equipped with a telescopic filler. If the
level is too low, lift the reservoir cap 4
fig. 155 upwards and then lift the filler,
as shown in the figure, and add the fluiddescribed in the "Technical
Specifications" chapter. After having
topped up the fluid, arrange the filler
correctly and then press on the cap until
you hear it click.
IMPORTANT With a low fluid level
(indicated by the dedicated symbol
appearing on the instrument panel
display), the headlight washer system
does not work, even though the screen
washers continue to work.BRAKE FLUID
Check that the fluid is at the max. level. If
the liquid level in the tank is insufficient,
contact an Alfa Romeo Dealership to
have the system checked.
AUTOMATIC TRANSMISSION
ACTIVATIONSYSTEM OIL
5)
The transmission control oil level should
only be checked at an Alfa Romeo
Dealership.
BATTERY
162) 163) 164) 165)
70)
6)
The battery does not require the
electrolyte to be topped up with distilled
water. A periodic check carried out at an
Alfa Romeo Dealership is, however,
necessary to check efficiency.
Follow the battery manufacturer's
instructions for maintenance.
Useful advice for extending the life of
your battery
To avoid draining your battery and make
it last longer, observe the following
instructions:
when you park the car, ensure that the
doors, tailgate and bonnet are closed
properly, to prevent any lights from
15409026S0007EM
15509086S0666EM
171

remaining on inside the passenger's
compartment;
switch off all roof lights inside the car:
the car is however equipped with a
system which switches all internal lights
off automatically;
do not keep accessories (e.g. Connect
system, hazard warning lights, etc.)
switched on for a long time when the
engine is not running;
before performing any operation on
the electrical system, disconnect the
cable from the negative battery terminal.
IMPORTANT If the charge level remains
under 50% for a long time, the battery is
damaged by sulphation, reducing its
capacity and efficiency at start-up. The
battery is also more prone to the risk of
freezing (already at 14 °F / -10°C).
WARNING
156)Never smoke while working in the
engine compartment: gas and inflammable
vapours may be present, with the risk of fire.
157)Be very careful when working in the
engine compartment when the engine is hot:
you may get burned. Do not get too close to
the radiator cooling fan: the electric fan may
start; danger of injury. Scarves, ties and
other loose clothing might be pulled by
moving parts.158)If the engine oil is being topped up, wait
for the engine to cool down before loosening
the filler cap, particularly for vehicles with
aluminium cap (where provided). WARNING:
risk of burns!
159)The cooling system is pressurised. If
necessary, only replace the plug with
another original or the operation of the
system may be adversely affected. Do not
remove the reservoir plug when the engine is
hot: you risk scalding yourself.
160)Do not travel with the windscreen
washer fluid reservoir empty: the
windscreen washer is essential for
improving visibility. Repeated operation of
the system without fluid could damage or
cause rapid deterioration of some system
components.
161)Some commercial additives for
windscreen washer fluid are flammable. The
engine compartment contains hot
components which may start a fire.
162)Battery fluid is poisonous and
corrosive. Avoid contact with the skin and
eyes. Keep open flames away from the
battery and do not use objects that might
create sparks: risk of explosion and fire.
163)Using the battery with insufficient
fluid irreparably damages the battery and
may cause an explosion.
164)If the vehicle must remain unused for a
long time at a very low temperature, remove
the battery and take it to a warm place, to
avoid freezing.
165)When performing any operation on the
battery or near it, always protect your eyes
with special goggles.
IMPORTANT
65)Be careful not to confuse the various
types of fluids while topping up: they are not
compatible with each other! Topping up with
an unsuitable fluid could severely damage
your vehicle.
66)The oil level must never exceed the MAX
mark.
67)If the MAX mark is exceeded (last notch
on the right turns red) after the top-up, go to
an Alfa Romeo Dealership as soon as
possible to have the oil in excess removed.
68)Do not add oil with specifications other
than those of the oil already in the engine.
69)Use a fluid of the same type as that
already present in the reservoir for any
topping up of the engine cooling system. The
fluid cannot be mixed with other types of
antifreeze fluids. In the event of topping up
with an unsuitable product, under no
circumstances start the engine and contact
an Alfa Romeo Dealership.
70)When you need to disconnect or remove
the battery, do not close the boot. Open the
boot manually if it is locked.
172
SERVICING AND CARE

83)Avoid washing with rollers and/or
brushes in washing stations. Wash the car
only by hand using neutral pH detergents; dry
it with a wet chamois leather. Abrasive
products and/or polishes should not be used
for cleaning the car. Bird droppings must be
washed off immediately and thoroughly as
the acid they contain is particularly
aggressive. Avoid (if at all possible) parking
the vehicle under trees; remove vegetable
resins immediately as, when dried, it may
only be possible to remove them with
abrasive products and/or polishes, which is
highly inadvisable as they could alter the
typical opaqueness of the paint. Do not use
pure windscreen washer fluid for cleaning
the front windscreen and rear window; dilute
it min. 50% with water. Only use pure screen
washer fluid when strictly necessary due to
outside temperature conditions.
IMPORTANT
7)Detergents pollute the environment. Only
wash your vehicle in areas equipped to
collect and treat wastewater from this type
of activity.
INTERIOR
174) 175) 176)
Periodically check the cleanliness of the
interior, beneath the mats, which could
cause oxidation of the sheet metal.
PLASTIC AND COATED PARTS
84)
Clean interior plastic parts with a damp
cloth (if possible made from microfibre),
and a solution of water and neutral,
non-abrasive detergent.
To clean oily or persistent stains, use
specific products free from solvents and
designed to maintain the original
appearance and colour of the
components.
Remove any dust using a microfibre
cloth, if necessary moistened with water.
The use of paper tissues is not
recommended as these may leave
residues.
WARNING
174)Never use flammable products, such as
petrol ether or rectified petrol to clean the
inside of the car. The electrostatic charges
which are generated by rubbing during the
cleaning operation may cause a fire.
175)Do not keep aerosol cans in the car:
they might explode. Aerosol cans must not
be exposed to a temperature exceeding
50°C. When the vehicle is exposed to
sunlight, the internal temperature can
greatly exceed this value.
176)There must be no obstacles on the
floor underneath the pedals; make sure that
mats are always flat and do not interfere
with the pedals.
177)Do not use aggressive organic
substance such as: gasoline, kerosene, oil,
acetone or solvents.
IMPORTANT
84)Never use alcohol, petrols and
derivatives to clean the dashboard and
instrument panel lens.
179

NAVIGATION MODE
(where provided)
IMPORTANT In the interest of safety and
to reduce distractions while you are
driving, you should always plan a route
before you start driving.
To plan a route, do the following:
Activate the NAVIGATION mode by
selecting it on the main menu fig. 170;
Activate the "Set destination"
function;
To insert the address, select the item to
add (Country, City) on the circular keypad,
choosing the keys to compose the
desired name; proceeding with keying in
the letters, the system automatically
completes the word and on the right of
the display offers a list of options that
apply to the entered letters. You can now
either complete the word or go to the list
of suggestions by moving the Rotary Padrightwards or by pointing to “OK” and
pressing the Rotary Pad.
Or
Select an address on the "Recent
destinations" list.
Or
Select an address on the "Favourite
destinations" list.
Once the desired destination has been
set, select "Start navigation" function.
The system suggests three alternatives
according to the set criteria (fastest, no
toll routes etc.); select the preferred
alternative using the Rotary Pad.
With navigation started, using the control
bar on the display, you can choose from
the following options:
Interrupt navigation: lets you interrupt
navigation;
Navigation volume: allows to set the
message volume;
Route management: lets you refine
your route choice, offering a series of
options;
Route Preview: this is used to see a
preview of the planned route;
Zoom: lets you enlarge/reduce the
map;
Map explore: lets you move within the
map.
SETTINGS
To access the user-programmable
functions, open the main menu by
pressing the MENU button, then select
SETTINGS by turning and pressing the
Rotary Pad.
The following menu items can be found
here fig. 171:
Lights;
Units & Language;
Time and Date;
Safety;
Driver assistance;
Doors & Locks;
Cluster;
Infotainment;
System.17011186S0003EM
17111126S0009EM
213

Lights
To access the “Lights” function, select it
by turning the Rotary Pad and press the
Rotary Pad to activate. The following
settings can be modified when this mode
is selected:
Headlight sensor;
Follow me;
Cornering lights;
Flash lights when locking;
Daytime running lights;
Courtesy lights;
Interior lights;
Automatic High Beam;
Restore settings.
Units & Language
To access the “Units and languages”
function, select it by turning the Rotary
Pad and press the Rotary Pad to activate.
The following settings can be modified
when this mode is selected:
Units;
Language;
Restore settings.Time and Date
To access the “Time & date” function,
select it by turning the Rotary Pad and
press the Rotary Pad to activate. The
following settings can be modified when
this mode is selected:
Sync with GPS Time;
Set time;
Time format;
Set Date;
Restore settings.
Safety
To access the “Safety” function, select it
by turning the Rotary Pad and press the
Rotary Pad to activate. The following
settings can be modified when this mode
is selected:
Speed Limiter
This lets you activate/deactivate the
function warning that you have exceeded
the set speed.
Speed Limiter - Set Speed
Lets you set the speed limit value. By
turning the Rotary Pad, the speed
increases by 5 mph (5 km/h), on rotation,
from a minimum of 20 mph (30 km/h) to a
maximum of 110 mph (180 km/h).
Forward Collision Warning
Allows you to select the intervention
readiness for the anti-collision system.
The options available are:
"Status": lets you activate/deactivate
the system (where provided);
"Mode": used to set the following
operating modes: “Warning-brake”,
“Warning”, “Off” (where provided);
"Sensitivity": allows you to select the
intervention readiness for the system
according to the distance of the obstacle
(near, average, far).
Lane Departure Warning
This function can be used to select the
"readiness" of the Lane Departure
system to intervene. The “Sensitivity"
option is provided: allows you to select
the intervention readiness for the system
(high, low).
Blind Spot Monitoring
This function can be used to set the
warning linked to the presence of objects
in the door mirror blind spot.
The options available are:
"Sound & Display": the system warns
the driver that an obstacle is present
through acoustic (via the speakers in the
car) and visual indications using warning
lights on the door mirrors;
"Sound Only": the system warns the
driver that an obstacle is present through
acoustic indications only, via the
speakers in the car;
"Off": system disengaged.
214
MULTIMEDIA