2018 YAMAHA YZF-R3 fuel pressure

Motorcycle care and stora ge
7-2
7
fected
area any lon ger than in-
structed . Also, thorou ghly rinse
the area off with water, immed i-
ately dry it, an d then apply a cor-
rosion protection spray.
 Improper cleanin g can damag e
plastic parts (such as cowlin gs,
panels, win dshield s, hea dlig ht
lenses, meter lenses, etc.) an d
the mufflers. Use only a soft,
clean cloth or spon ge with wa-
ter to clean plastic. However, if
the plastic parts cannot be thor-
ou ghly cleaned with water, di-
lute d mil d d eter gent with water
may be used . Be sure to rinse
off any d etergent resi due usin g
plenty of water, as it is harmful
to plastic parts.
 Do not use any harsh chemical
prod ucts on plastic parts. Be
sure to avoi d usin g cloths or
spon ges which have b een in
contact with stron g or a brasive
cleanin g pro du
cts, solvent or
thinner, fuel ( gasoline), rust re-
movers or inhi bitors, brake flui d,
antifreeze or electrolyte.
 Do not use hi gh-pressure wash-
ers or steam-jet cleaners since
they cause water seepag e and
d eterioration in the followin g ar-
eas: seals (of wheel an d swin g-
arm bearin gs, fork an d b rakes),
electric components (couplers,
connectors, instruments,
switches an d li ghts), breather
hoses an d vents.
 For motorcycles equippe d with
a win dshiel d: Do not use stron g
cleaners or har d spon ges as
they will cause dullin g or scratchin
g. Some cleanin g
compoun ds for plastic may
leave scratches on the win d-
shiel d. Test the pro duct on a
small hidden part of the win d-
shiel d to make sure that it does
not leave any marks. If the win d-
shiel d is scratche d, use a quality
plast

ic polishin g compoun d af-
ter washin g.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on roads
during winter are extremely corrosive
in combination with water, carry out
the following steps after each ride in
the rain, near the sea or on salt-
sprayed roads.
TIP
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
NOTICE: Do not use warm wa-
ter since it increases the corro-
sive action of the salt.
[ECA10792]
UBR5E0E0.book Page 2 Wednesday, July 5, 2017 11:10 AM

10-1
10
Index
A
ABS ...................................................... 3-14
ABS warning light ................................... 3-3
Air filter element and check hose,
replacing and cleaning ....................... 6-13
Auxiliary light bulb ................................ 6-35
B
Battery .................................................. 6-30
Brake and clutch levers,
checking and lubricating .................... 6-27
Brake and shift pedals, checking and lubricating .................... 6-26
Brake fluid, changing ........................... 6-23
Brake fluid level, checking ................... 6-22
Brake lever ........................................... 3-13
Brake lever free play, checking ............ 6-20
Brake light switches ............................. 6-20
Brake pedal .......................................... 3-14
C
Cables, checking and lubricating ......... 6-25
Canister .................................................. 6-8
Care ........................................................ 7-1
Catalytic converter ............................... 3-18
Clutch lever .......................................... 3-12
Clutch lever free play, adjusting ........... 6-18
Coolant ................................................. 6-11
D
Data recording, vehicle .......................... 9-3
Diagnostic connector ............................. 9-2
Dimmer switch ..................................... 3-11
Drive chain, cleaning and lubricating ... 6-25
Drive chain slack .................................. 6-23
E
Engine break-in ...................................... 5-4
Engine oil and oil filter cartridge ............. 6-8
Engine serial number.............................. 9-1
Engine stop switch ............................... 3-12
Engine trouble warning light................... 3-3
F
Front and rear brake pads, checking ... 6-21
Front fork, checking ............................. 6-28
Fuel....................................................... 3-16
Fuel tank cap........................................ 3-15
Fuel tank overflow hose ....................... 3-17
Fuses, replacing ................................... 6-31
H
Handlebar switches.............................. 3-11
Headlight bulb, replacing ..................... 6-33
Helmet holders ..................................... 3-20
High beam indicator light ....................... 3-2 Horn switch........................................... 3-12
I
Identification numbers ............................ 9-1
Ignition circuit cut-off system ............... 3-24
Indicator lights and warning lights .......... 3-2
L
License plate light bulb, replacing ........ 6-36
Luggage strap holders .......................... 3-23
M
Main switch/steering lock ....................... 3-1
Maintenance and lubrication, periodic ... 6-4
Maintenance, emission control
system .................................................. 6-3
Matte color, caution ................................ 7-1
Model label ............................................. 9-1
Multi-function meter unit ........................ 3-4
N
Neutral indicator light.............................. 3-2
O
Oil pressure warning light ....................... 3-2
P
Parking .................................................... 5-4
Part locations .......................................... 2-1
Pass switch........................................... 3-11
R
Rear view mirrors .................................. 3-21
S
Safety information................................... 1-1
Seats ..................................................... 3-18
Shifting .................................................... 5-3
Shift pedal............................................. 3-13
Shift timing indicator light ....................... 3-4
Shock absorber assembly, adjusting ... 3-22
Sidestand .............................................. 3-23
Sidestand, checking and lubricating .... 6-27
Spark plugs, checking ............................ 6-7
Specifications ......................................... 8-1
Starting the engine.................................. 5-2
Start switch ........................................... 3-12
Steering, checking ................................ 6-29
Storage ................................................... 7-4
Storage compartment ........................... 3-21
Supporting the motorcycle ................... 6-37
Swingarm pivots, lubricating ................ 6-28
T
Tail/brake light ...................................... 6-35
Throttle grip and cable, checking and lubricating .................... 6-26
Throttle grip free play, checking ........... 6-15
Tires ...................................................... 6-16
UBR5E0E0.book Page 1 Wednesday, July 5, 2017 11:10 AM