Instrument and control functions
3-9
3
“AVE_ _._ MPG” (for the UK): The
average distance that can be trav-
eled on 1.0 Imp. gal of fuel is
shown.
To switch between the average fuel
consumption displays, push the “SEL”
button for one second.
To reset the average fuel consumption
display, push the “RES” button for at
least one second.
TIP
After resetting the average fuel con-
sumption display, “_ _._” is shown until
the vehicle has traveled 1 km (0.6 mi).
Oil chan ge tripmeter
The oil change tripmeter shows the
distance traveled since it was last reset
(i.e., since the last oil change).
The oil change indicator “OIL” will flash
at the initial 1000 km (600 mi), then at
5000 km (3000 mi) and every 5000 km
(3000 mi) thereafter to indicate that the
engine oil should be changed.
After changing the engine oil, reset the
oil change tripmeter and the oil change
indicator. To reset them both, select
the oil change tripmeter, and then push
the “RES” button for one second.
Then, while “OIL” and the oil change tripmeter are flashing, push the “RES”
button for three seconds. The oil chan-
ge indicator will be reset.
If the engine oil is changed before the
oil change indicator comes on (i.e., be-
fore the periodic oil change interval has
been reached), the oil change tripmeter
must be reset for the next periodic oil
change to be indicated at the correct
time.
Shift timin
g in dicator li ght
The shift timing indicator light has four
settings which can be adjusted. Flashing pattern: this function al-
lows you to choose whether or not
the indicator light will come on and
whether it should flash or stay on
when activated.
Activation point: this function al-
lows you to select the engine
speed at which the indicator light
is activated.
Deactivation point: this function
allows you to select the engine
speed at which the indicator light
is deactivated.
Brightness: this function allows
you to adjust the brightness of the
indicator light.
1. Oil change indicator “OIL”
2. Oil change tripmeter
MPH
km/h
km
21
1. Shift timing indicator light
2. Brightness level display
1
2
km/hMPH
UBR5E0E0.book Page 9 Wednesday, July 5, 2017 11:10 AM
Instrument and control functions
3-10
3 To adjust the shift timing indicator light
1. Turn the key to “ ”.
2. Push and hold the “SEL” button.
3. Turn the key to “ ”, and then re-
lease the “SEL” button after five
seconds. The shift timing indicator
light can now be adjusted.
To set the flashing pattern
1. Push the “RES” button to select one of the following flashing pat-
tern settings: On: the indicator light stays
on when activated. (This set-
ting is selected when the indi-
cator light stays on.)
Flash: the indicator light
flashes when activated. (This
setting is selected when the
indicator light flashes four
times per second.)
Off: the indicator light is deac-
tivated; in other words, it
does not come on or flash.
(This setting is selected when
the indicator light flashes
once every two seconds.)
2. Push the “SEL” button to confirm the selected flashing pattern. The
shift timing indicator light changes
to the activation point setting mo-
de.
The tachometer will show the current
setting r/min for the activation point
and deactivation point setting modes.
To set the shift activation point
TIP
The shift timing indicator light activa-
tion point can be set between 7000
r/min and 13500 r/min. From 7000 r/min to 12000 r/min, the indicator light
can be set in increments of 500 r/min.
From 12000 r/min to 13500 r/min, the
indicator light can be set in increments
of 200 r/min.
1. Push the “RES” button to select
the desired engine speed for acti-
vating the indicator light.
2. Push the “SEL” button to confirm the selected engine speed. The
control mode changes to the de-
activation point setting mode.
To set the deactivation point
TIP
The shift timing indicator light de-
activation point can be set be-
tween 7000 r/min and 13500
r/min. From 7000 r/min to 12000
r/min, the indicator light can be set
in increments of 500 r/min. From
12000 r/min to 13500 r/min, the in-
dicator light can be set in incre-
ments of 200 r/min.
Be sure to set the deactivation
point to a higher engine speed
than for the activation point, other-
wise the shift timing indicator light
will not come on.
1. Push the “RES” button to select
the desired engine speed for de-
activating the indicator light.
2. Push the “SEL” button to confirm the selected engine speed. The
control mode changes to the
brightness setting mode.
To adjust the brightness
1. Push the “RES” button to select the desired shift indicator light
brightness level.
UBR5E0E0.book Page 10 Wednesday, July 5, 2017 11:10 AM
