Operation and important riding points
6-2
1
2
3
4
567
8
9
10
11
12
Immobilizer system indicator
light
TIP
The oil pressure and coolant tem-
perature warning light will come
on, go off briefly, and then remain
on until the engine is started.
The ABS warning light will remainon until the vehicle starts moving.
NOTICE
ECA24110
If a warning or indicator light does
not work as described above, have aYamaha dealer check the vehicle.
5. Shift the transmission into the neu- tral position (or hold the clutch le-
ver pulled with the sidestand up).
6. Push the start switch, and release it when the engine starts.
If the engine does not start within 5
seconds of pressing the start
switch, wait 10 seconds before
pressing the switch again to allow
battery voltage to restore.
NOTICE
ECA11043
For maximum engine life, never ac-
celerate hard when the engine iscold!
EAU67082
ShiftingShifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing hills,
etc.
This model is equipped with QSS. See
pages 3-3 and 4-17.TIPTo shift into neutral ( ), gently de-
press the shift pedal from 2nd gear, orslightly raise it while in 1st gear.NOTICE
ECA22521
Even with the transmission in
1. Gear positions
2. Shift pedal
1 2 3 4
5 6
N
1
2
BX4-9-E1_1.book 2 ページ 2018年4月27日 金曜日 午後4時3分
Periodic maintenance and adjustment
7-6
1
2
3
4
5
678
9
10
11
12
24 *Rear suspension
relay arm and
connecting arm
pivoting points Check operation.
25 Engine oil Change (warm engine before
draining).
Check oil level and vehicle for oil leakage.
26 Engine oil filter
cartridge Replace.
27 *Cooling system Check coolant level and vehicle
for coolant leakage.
Change. Every 3 years
28 *EXUP system Check operation, cable free play
and pulley position.
29 *Front and rear brake
switches Check operation.
30 *Moving parts and
cables Lubricate.
31 *Throttle grip
housing and cable Check operation and free play.
Adjust the throttle cable free play
if necessary.
Lubricate the throttle grip housing and cable.
32 *Lights, signals and
switches Check operation.
Adjust headlight beam.
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READING
ANNUAL
CHECK
1000 km
(600 mi) 10000 km
(6000 mi) 20000 km
(12000 mi) 30000 km
(18000 mi) 40000 km
(24000 mi)
BX4-9-E1_1.book 6 ページ 2018年4月27日 金曜日 午後4時3分
Periodic maintenance and adjustment
7-15
1
2
3
4
5
67
8
9
10
11
12 10. Check the oil filler cap O-ring for
damage, and replace it if neces-
sary.
11. Install and tighten the oil filler cap.
12. Start the engine, and then let it idle for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
TIPAfter the engine is started, the oil pres-
sure and coolant temperature warning
light should go off if the oil level is suffi-cient.
NOTICE
ECA22490
If the oil pressure and coolant tem-
perature warning light flickers or re-
mains on even if the oil level is
correct, immediately turn the engine
off and have a Yamaha dealer checkthe vehicle.
13. Turn the engine off, wait a few min- utes until the oil settles, and then
check the oil level and correct it if
necessary.
14. Install the cowling and panel.
EAUS1203
CoolantThe coolant level should be checked
regularly. In addition, the coolant must
be changed at the intervals specified in
the periodic maintenance chart.TIPIf genuine Yamaha coolant is not avail-
able, use an ethylene glycol antifreeze
containing corrosion inhibitors for alu-
minum engines and mix with distilledwater at a 1:1 ratio.
EAU20097
To check the coolant level
Since the coolant level varies with en-
gine temperature, check when the en-
gine is cold. 1. Park the vehicle on a level surface.
2. With the vehicle in an upright posi- tion, look at the coolant level in the
1. Engine oil filler cap
2. O-ring
21
Recommended coolant:YAMALUBE coolant
Coolant quantity: Coolant reservoir (max level mark):0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator (including all routes): 2.25 L (2.38 US qt, 1.98 Imp.qt)
BX4-9-E1_1.book 15 ページ 2018年4月27日 金曜日 午後4時3分
Periodic maintenance and adjustment7-16
1
2
3
4
5
678
9
10
11
12
reservoir.
3. If the coolant is at or below the minimum level mark, remove the
coolant reservoir cap. WARNING!
Remove only the coolant reser-
voir cap. Never attempt to re-
move the radiator cap when the
engine is hot.
[EWA15162]
4. Add coolant to the maximum level mark. NOTICE: If coolant is not
available, use distilled water or
soft tap water instead. Do not
use hard water or salt water
since it is harmful to the engine.
If water has been used instead
of coolant, replace it with cool-
ant as soon as possible, other-
wise the cooling system will not
be protected against frost and
corrosion. If water has been
added to the coolant, have a
Yamaha dealer check the anti-
freeze content of the coolant as
soon as possible, otherwise the
effectiveness of the coolant will be reduced.
[ECA10473]
5. Install the coolant reservoir cap.
EAU33032
Changing the coolant
The coolant must be changed at the in-
tervals specified in the periodic mainte-
nance and lubrication chart. Have a
Yamaha dealer change the coolant.
WARNING! Never attempt to remove
the radiator cap when the engine is
hot.
[EWA10382]
1. Maximum level mark
2. Minimum level mark1
2
1. Coolant reservoir cap
1
BX4-9-E1_1.book 16 ページ 2018年4月27日 金曜日 午後4時3分
Periodic maintenance and adjustment7-38
1
2
3
4
5
678
9
10
11
12
Engine overheating
WARNING
EWAT1041
Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the de-
tent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the capwhile turning it counterclockwise, and then remove the cap.
TIPIf coolant is not available, tap water can be temporarily
used instead, provided that it is changed to the recommended coolantas soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
BX4-9-E1_1.book 38 ページ 2018年4月27日 金曜日 午後4時3分
9-1
1
2
3
4
5
6
7
89
10
11
12
Specifications
EAU70621
Dimensions:Overall length: 2055 mm (80.9 in)
Overall width: 690 mm (27.2 in)
Overall height: 1150 mm (45.3 in)
Seat height:
855 mm (33.7 in) (YZF-R1)
860 mm (33.9 in) (YZF-R1M)
Wheelbase:
1405 mm (55.3 in)
Ground clearance: 130 mm (5.12 in)
Minimum turning radius: 3.3 m (10.83 ft)Weight:Curb weight:200 kg (441 lb) (YZF-R1)
201 kg (443 lb) (YZF-R1M)Engine:Combustion cycle:
4-stroke
Cooling system:
Liquid cooled
Valve train: DOHC
Cylinder arrangement: Inline
Number of cylinders:
4-cylinder
Displacement: 998 cm
3
Bore stroke:
79.0 50.9 mm (3.11 2.00 in)
Compression ratio:
13.0 : 1
Starting system: Electric starter
Lubrication system: Wet sumpEngine oil:Recommended brand:YAMALUBE
Type: Full synthetic
SAE viscosity grades:
10W-40, 15W-50
Recommended engine oil grade: API service SG type or higher, JASO stan-
dard MA
Engine oil quantity: Oil change:
3.90 L (4.12 US qt, 3.43 Imp.qt)
With oil filter removal: 4.10 L (4.33 US qt, 3.61 Imp.qt)Coolant quantity:Coolant reservoir (up to the maximum level
mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator (including all routes):
2.25 L (2.38 US qt, 1.98 Imp.qt)Air filter:Air filter element:Oil-coated paper element
Fuel:Recommended fuel:Premium unleaded gasoline (Gasohol
[E10] acceptable)
Fuel tank capacity:
17 L (4.5 US gal, 3.7 Imp.gal)
Fuel reserve amount: 3.0 L (0.79 US gal, 0.66 Imp.gal)Fuel injection:Throttle body:
ID mark: 2CR4 10Spark plug(s):Manufacturer/model:NGK/LMAR9E-J
Spark plug gap: 0.6–0.7 mm (0.024–0.028 in)Clutch:Clutch type:Wet, multiple-discDrivetrain:Primary reduction ratio:
1.634 (67/41)
Final drive: Chain
Secondary reduction ratio: 2.563 (41/16)
Transmission type:
Constant mesh 6-speed
Gear ratio: 1st:
2.600 (39/15)
2nd: 2.176 (37/17)
BX4-9-E1_1.book 1 ページ 2018年4月27日 金曜日 午後4時3分
Specifications
9-3
1
2
3
4
5
6
7
89
10
11
12
Brake/tail light: LED
Front turn signal light:
LED
Rear turn signal light: LED
Auxiliary light: LED
License plate light:
LED
Meter lighting: LED
Neutral indicator light: LED
High beam indicator light:
LED
Turn signal indicator light: LED
Stability control indicator light: LED
Oil pressure and coolant temperature warning
light:
LED
Fuel level warning light:
LED
Engine trouble warning light: LED
Steering damper and suspension warning
light: LED
ABS warning light: LED
Immobilizer system indicator light:
LED Shift timing indicator light:
LED
Fuse(s):Main fuse:50.0 A
Terminal fuse 1: 2.0 A
Headlight fuse:
7.5 A
Signaling system fuse: 7.5 A
Ignition fuse: 15.0 A
Radiator fan motor fuse:
15.0 A
Sub radiator fan motor fuse: 10.0 A
Hazard fuse: 7.5 A
ABS ECU fuse:
7.5 A
Fuel injection system fuse: 15.0 A
SCU fuse: 7.5 A (YZF-R1M)
ABS motor fuse:
30.0 A
ABS solenoid fuse: 15.0 A
Backup fuse: 7.5 A
Electronic throttle valve fuse:
7.5 A
BX4-9-E1_1.book 3 ページ 2018年4月27日 金曜日 午後4時3分
11-1
1
2
3
4
5
6
7
8
9
101112
Index
AABS warning light ................................... 4-6
Air filter element.................................... 7-17
Auxiliary DC connector ......................... 4-48
Auxiliary system warning light ................ 4-8BBattery .................................................. 7-31
Brake and clutch levers, checking and lubricating ........................................... 7-28
Brake and shift pedals, checking and
lubricating ........................................... 7-28
Brake fluid, changing ............................ 7-25
Brake fluid level, checking .................... 7-24
Brake lever ........................................... 4-32
Brake lever free play, checking ............ 7-22
Brake light switches .............................. 7-23
Brake pedal .......................................... 4-32
Brake system ........................................ 4-33CCables, checking and lubricating .......... 7-27
Canister ................................................ 7-12
Care ........................................................ 8-1
Catalytic converter ................................ 4-37
CCU ...................................................... 4-39
Clutch lever........................................... 4-31
Clutch lever free play, adjusting ........... 7-21
Coolant ................................................. 7-15
Cowlings and panels, removing and installing ............................................... 7-8DData recording, vehicle ......................... 10-2
Diagnostic connecto r ............................ 10-2
Dimmer switch ........................................ 4-4
Display, main screen .............................. 4-8 Display, menu screen ............................ 4-14
Document storage ................................. 4-40
Drive chain, cleaning
and lubricating .... 7-26
Drive chain slack ................................... 7-25
EEngine break-in ....................................... 6-3
Engine idling speed, checking............... 7-17
Engine oil and oil filter cartridge ............ 7-12
Engine serial number ............................ 10-1
Engine trouble warning light .................... 4-6
EXUP system ........................................ 4-47FFront and rear brake pads, checking .... 7-23
Front fork, adjusting .............................. 4-41
Front fork, checking............................... 7-30
Fuel ....................................................... 4-35
Fuel consumption, tips for reducing ........6-3
Fuel level warning light ............................4-6
Fuel tank cap......................................... 4-34
Fuel tank overflow hose ........................ 4-37
Fuses, replacing .................................... 7-33GGlossary ..................................................3-4HHandlebar switches ................................. 4-3
Hazard switch.......................................... 4-4
High beam indicator light .........................4-6
Horn switch .............................................4-4IIdentification numbers ........................... 10-1
Ignition circuit cut-off system ................. 4-49
Immobilizer system ................................. 4-1
Immobilizer system indicator light ........... 4-7
Indicator lights and warning lights ........... 4-6
MMain switch/steering lock ........................ 4-2
Maintenance and lubrication, periodic .... 7-4
Maintenance, emission control system ... 7-3
Matte color, caution ................................ 8-1
Model label ........................................... 10-2NNeutral indicator light .............................. 4-6OOil pressure and coolant temperature
warning light ......................................... 4-8PParking.................................................... 6-4
Part locations .......................................... 2-1
Pass/LAP switch ..................................... 4-4RRear view mirrors.................................. 4-41SSafety information ................................... 1-1
Seats..................................................... 4-38
Shift indicator light .................................. 4-7
Shifting .................................................... 6-2
Shift pedal ............................................. 4-31
Shock absorber assembly, adjusting .... 4-44
Sidestand .............................................. 4-48
Sidestand, checking and lubricating ..... 7-29
Spark plugs, checking ........................... 7-11
Special features ...................................... 3-1
Specifications.......................................... 9-1
Stability control indicator light ................. 4-7
Starting the engine.................................. 6-1
Steering, checking ................................ 7-30
Stop/Run/Start switch ............................. 4-4
Storage ................................................... 8-4
BX4-9-E1_1.book 1 ページ 2018年4月27日 金曜日 午後4時3分