2018 YAMAHA XSR 900 lock

Periodic maintenance and adjustment6-23
1
2
3
4
567
8
9
10
11
12
EAU57971
To adjust the drive chain slack
Consult a Yamaha dealer before ad-
justing the drive chain slack. 1. Loosen the axle nut and the lock- nut on each side of the swingarm.
2. To tighten the drive chain, turn the drive chain slack adjusting bolt on
each side of the swingarm in direc-
tion (a). To loosen the drive chain,
turn the adjusting bolt on each side
of the swingarm in direction (b),
and then push the rear wheel for-
ward.
TIPUsing the alignment marks and notch
on each side of the swingarm, make
sure that both drive chain pullers are in
the same position for proper wheelalignment. 3. Tighten the axle nut, then the lock-
nuts to their specified torques.
4. Make sure that the drive chain pull- ers are in the same position, the
drive chain slack is correct, and
the drive chain moves smoothly.
1. Axle nut
2. Locknut
2
1
1. Drive chain slack adjusting bolt
(a)(b)
1
1. Notch
2. Alignment marks
3. Drive chain pullerTightening torques:Axle nut:150 N·m (15 kgf·m, 111 lb·ft)
Locknut:
16 N·m (1.6 kgf·m, 12 lb·ft)
3
12
UB90E2.book 23 ページ ２０１８年６月５日　火曜日　午後５時４０分

Periodic maintenance and adjustment6-35
1
2
3
4
567
8
9
10
11
12
EAU24205
Replacing a turn signal light
bulb1. Remove the turn signal light lens by removing the screw.
2. Remove the burnt-out bulb by pushing it in and turning it counter-
clockwise. 3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the screw. NOTICE: Do not over-
tighten the screw, otherwise the
lens may break.
[ECA11192] EAU24331
License plate lightIf the license plate light does not come
on, have a Yamaha dealer check the
electrical circuit or replace the bulb.
1. Turn signal light lens
2. Screw
1
2
1. Turn signal light bulb
1
UB90E2.book 35 ページ ２０１８年６月５日　火曜日　午後５時４０分

Periodic maintenance and adjustment
6-38
1
2
3
4
56
7
8
9
10
11
12 Engine overheating
WARNING
EWA10401

Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.

After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hissingsound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
TIPIf coolant is not available, tap water can be temporarily us
ed instead, provided that it is changed to the recommended coolantas soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
UB90E2.book 38 ページ ２０１８年６月５日　火曜日　午後５時４０分

10-1
1
2
3
4
5
6
7
8
910
11
12
IndexAABS ....................................................... 3-17
ABS warning light.................................... 3-5
Air filter element .................................... 6-14
Auxiliary DC connector ......................... 3-30
Auxiliary light bulb, replacing ................ 6-34BBattery................................................... 6-28
Brake and clutch levers, checking and lubricating ........................................... 6-26
Brake and shift pedals, checking and lubricating ........................................... 6-25
Brake fluid, changing ............................ 6-22
Brake fluid level, checking .................... 6-20
Brake lever ............................................ 3-16
Brake lever free play, checking ............. 6-19
Brake light switches .............................. 6-19
Brake pedal ........................................... 3-17
Brake/tail light ....................................... 6-34CCables, checking and lubricating .......... 6-24
Canister................................................. 6-10
Care ........................................................ 7-1
Catalytic converter ................................ 3-22
Clutch lever ........................................... 3-15
Clutch lever free play, adjusting ............ 6-18
Coolant.................................................. 6-13
Coolant temperature warning light .......... 3-4DData recording, vehicle ........................... 9-2
Diagnostic connector .............................. 9-2
Dimmer switch ...................................... 3-14
D-mode (drive mode) ............................ 3-13
Drive chain, cleaning and lubricating .... 6-24 Drive chain slack .................................. 6-22
EEngine break-in ...................................... 5-3
Engine idling speed, checking .............. 6-14
Engine oil .............................................. 6-10
Engine serial number.............................. 9-1
Engine trouble warning light ................... 3-5FFront and rear brake
pads, checking .... 6-20
Front fork, adjusting .............................. 3-24
Front fork, checking .............................. 6-27
Fuel....................................................... 3-20
Fuel consumption, tips for reducing........ 5-3
Fuel tank cap ........................................ 3-19
Fuel tank overflow hose and breather hose ................................................... 3-22
Fuses, replacing ................................... 6-30HHandlebar switches .............................. 3-14
Hazard switch ....................................... 3-15
Headlight bulb, replacing ...................... 6-32
High beam indicator light ........................ 3-4
Horn switch ........................................... 3-14IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ................ 3-28
Immobilizer system ................................. 3-1
Immobilizer system indicator light........... 3-5
Indicator lights and warning lights .......... 3-4LLicense plate light ................................. 6-35
Luggage strap holders .......................... 3-27MMain switch/steering lock........................ 3-2 Maintenance and lubrication, periodic..... 6-5
Maintenance, emission control system ... 6-3
Matte color, caution ................................. 7-1
Model label .............................................. 9-2
Multi-function meter unit .......................... 3-6
NNeutral indicator light .............................. 3-4OOil level warning light .............................. 3-4PParking .................................................... 5-4
Part locations .......................................... 2-1
Pass switch ........................................... 3-14SSafety information ................................... 1-1
Seat ....................................................... 3-23
Shifting .................................................... 5-2
Shift pedal ............................................. 3-16
Shock absorber assembly, adjusting .... 3-25
Sidestand .............................................. 3-27
Sidestand, checking an
d lubricating...... 6-26
Spark plugs, checking ............................. 6-9
Specifications .......................................... 8-1
Starting the engine .................................. 5-1
Steering, checking................................. 6-28
Stop/Run/Start switch............................ 3-15
Storage.................................................... 7-3
Storage compartment............................ 3-23
Supporting the motorcycle .................... 6-36
Swingarm pivots, lubricating ................. 6-27TThrottle grip and cable, checking and lubricating ........................................... 6-25
Throttle grip free play, checking ............ 6-15
UB90E2.book 1 ページ ２０１８年６月５日　火曜日　午後５時４０分