2018 YAMAHA MT07 TRACER display

Instrument and control functions
3-7
3
EAUM3760
Multi-function meter unit
The multi-function meter unit is
equipped with the following:
speedometer
tachometer
clock
fuel meter
eco indicator
transmission gear display
multi-function display
WARNING
EWA12423
Be sure to stop the vehicle before
making any setting changes to the
multi-function meter unit. Changing
settings while riding can distract the
operator and increase the risk of an
accident.
TIP
Except when accessing the
brightness control mode or when
displaying the clock, the key must
be turned to “ON” before you can
use the left and right set buttons to
adjust the multi-function meter.
For the UK: To switch between ki-
lometers and miles, press the left
set button for three seconds.
Speedometer
The speedometer shows the vehicle’s
traveling speed.
Tachometer
The tachometer allows the rider to
monitor the engine speed and keep it
within the ideal power range.
1. Left set button
2. Right set button
1. Fuel meter
2. Clock
3. Transmission gear display
4. Eco indicator “ECO”
5. Speedometer
6. Tachometer
7. Multi-function display
12
67
21345
1. Tachometer
2. Tachometer red zone
12
UBC6E2E0.book Page 7 Tuesday, July 10, 2018 6:26 PM

Instrument and control functions
3-9
3 The eco indicator comes on when the
vehicle is being operated in an environ-
mentally friendly, fuel-efficient manner.
The indicator goes off when the vehicle
is stopped.
TIP
Consider the following tips to reduce
fuel consumption:
Avoid high engine speeds during
acceleration.
Travel at a constant speed.
Select the transmission gear that
is appropriate for the vehicle
speed.
Transmission gear display
The transmission gear display shows
the selected gear. The neutral position
is indicated by “–” and by the neutral
indicator light.Multi-function display
The multi-function display is equipped
with the following:
odometer
two tripmeters
fuel reserve tripmeter
instantaneous fuel consumption
average fuel consumption
coolant temperature
air temperature
brightness control mode
Navigating the multi-function dis-
play
Push the left set button to change the
display between the odometer “ODO”,
tripmeters “TRIP 1” and “TRIP 2”, in-
stantaneous fuel consumption “km/L”
or “L/100 km”, average fuel consump-
tion “AVE_ _._ km/L” or “AVE_ _._
L/100 km”, coolant temperature “_ _
°C”, and air temperature “Air_ _ °C” in
the following order:
ODO → TRIP 1 → TRIP 2 → km/L or
L/100 km → AVE_ _._ km/L or AVE_ _._
L/100 km → _ _ °C → Air_ _ °C → ODO
For the UK:
1. Transmission gear display
2. Neutral indicator light “ ”
12
1. Multi-function display
1
UBC6E2E0.book Page 9 Tuesday, July 10, 2018 6:26 PM

Instrument and control functions
3-10
3Push the left set button to change the
display between the odometer “ODO”,
tripmeters “TRIP 1” and “TRIP 2”, in-
stantaneous fuel consumption “km/L”,
“L/100 km” or “MPG”, average fuel
consumption “AVE_ _._ km/L”, “AVE_
_._ L/100 km” or “AVE_ _._ MPG”,
coolant temperature “_ _ °C”, and air
temperature “Air_ _ °C” in the following
order:
ODO → TRIP 1 → TRIP 2 → km/L,
L/100 km or MPG → AVE_ _._ km/L,
AVE_ _._ L/100 km or AVE_ _._ MPG →
_ _ °C → Air_ _ °C → ODO
TIP
Push the right set button to change the
display in the reverse order.
Odometer and tripmeters
The odometer shows the total distance
traveled by the vehicle.
The tripmeters show the distance trav-
eled since they were last reset.
To reset a tripmeter, use the left set
button to display the tripmeter you
want to reset, and then push the right
set button for one second.
TIP
The odometer will lock at 999999.
The tripmeters will lock at 9999.9
but can be manually reset.
Fuel reserve tripmeter
When the fuel level becomes low, the
last segment of the fuel meter will start
flashing. The fuel reserve tripmeter
“TRIP F” will automatically appear and
start counting the distance traveledfrom that point. In this case, push the
left set button to switch the display in
the following order:
TRIP F → km/L or L/100 km → AVE_
_._ km/L or AVE_ _._ L/100 km → _ _
°C → Air_ _ °C → ODO → TRIP 1 →
TRIP 2 → TRIP F
For the UK:
TRIP F → km/L, L/100 km or MPG →
AVE_ _._ km/L, AVE_ _._ L/100 km or
AVE_ _._ MPG → _ _ °C → Air_ _ °C →
ODO → TRIP 1 → TRIP 2 → TRIP F
TIP
Push the right set button to
change the display in the reverse
order.
You can manually reset the fuel re-
serve tripmeter, or after refueling
and traveling 5 km (3 mi), it will re-
set automatically and disappear
from the display.
Instantaneous fuel consumption
This function calculates the fuel con-
sumption under current riding condi-
tions.
The instantaneous fuel consumption
can be set to either “km/L”, “L/100 km”
or “MPG” (for the UK).
1. Instantaneous fuel consumption display
1
UBC6E2E0.book Page 10 Tuesday, July 10, 2018 6:26 PM

Instrument and control functions
3-11
3 “km/L”: The distance that can be
traveled on 1.0 L of fuel under the
current riding conditions is shown.
“L/100 km”: The amount of fuel
necessary to travel 100 km under
the current riding conditions is
shown.
“MPG” (for the UK): The distance
that can be traveled on
1.0 Imp.gal of fuel under the cur-
rent riding conditions is shown.
To switch the instantaneous fuel con-
sumption settings, push the left set
button for one second.
TIP
If traveling at speeds under 20 km/h

Average fuel consumption
This function calculates the average
fuel consumption since it was last re-
set.
The average fuel consumption can be
set to either “AVE_ _._ km/L”, “AVE_
_._ L/100 km” or “AVE_ _._ MPG” (for
the UK).
“AVE_ _._ km/L”: The average dis-
tance that can be traveled on 1.0 L
of fuel is shown.“AVE_ _._ L/100 km”: The average
amount of fuel necessary to travel
100 km is shown.
“AVE_ _._ MPG” (for the UK): The
average distance that can be trav-
eled on 1.0 Imp.gal of fuel is
shown.
To switch the average fuel consump-
tion settings, push the left set button
for one second.
To reset the average fuel consumption,
push the right set button for at least
one second.
TIP
After resetting the average fuel con-

the vehicle has traveled 1 km (0.6 mi).
Coolant temperature
This shows the coolant temperature
from 40 °C to 116 °C in 1 °C incre-
ments.
If the message “HI” flashes, stop the
vehicle, then stop the engine, and let it
cool. (See page 6-40.)
TIP
When the coolant temperature is
below 40 °C, “LO” will be dis-
played.
1. Average fuel consumption display
1
1. Coolant temperature display
1
UBC6E2E0.book Page 11 Tuesday, July 10, 2018 6:26 PM

Instrument and control functions
3-12
3The coolant temperature varies
with changes in the weather and
engine load.
Air temperature
This shows the air temperature from –9
°C to 99 °C in 1 °C increments. The
temperature displayed may vary from
the ambient temperature.
TIP
When the temperature is below –9
°C, “LO” will be displayed.
The accuracy of the temperature
reading may be affected by engine
heat when riding slowly (under 20
km/h [12 mi/h]) or when stopped
at traffic signals, etc.
Brightness control modeThe brightness control mode allows
you to adjust the brightness level of the
multi-function meter unit.
To adjust the brightness
1. Turn the key to “OFF”.
2. Push and hold the left set button.
3. Turn the key to “ON” and continue
pushing the left set button until the
display switches to the brightness
control mode.
4. Push the right set button to set the
brightness level.
5. Push the left set button to confirm
the selected brightness level and
exit the brightness control mode.
1. Air temperature display
1. Brightness level display
1
1
UBC6E2E0.book Page 12 Tuesday, July 10, 2018 6:26 PM