2018 VOLVO S90 T8 headlight bulb

3

Top tether anchors78
PRACTICAL INFORMATION
Passenger compartment storage spaces80
Engine compartment overview 81
Using the glove compartment 82
Tunnel console 83
Sun visors 84
Loading 84
Grocery bag holder 86
Load anchoring eyelets 86
Automatically arming/disarming the alarm 87
Octane rating 87
Opening/closing the fuel filler door 88
Tires 89
Tire sidewall designations 91
Wheel (rim) designations 93
Tire terminology 93
Tire direction of rotation 94
Tread wear indicator 95
Loading specifications 95
Uniform Tire Quality Grading 96
Snow tires and chains 97
Checking tire inflation pressure 97
Changing tires 99
Tools 99
Jack 100

Wheel bolts100
Removing a wheel 101
Installing a wheel 102
Tire Pressure Monitoring System (TPMS) 103
Checking tire inflation pressure 104
Reinflating tires equipped with the Tire Pressure Monitoring System (TPMS) 105
Calibrating the Tire PressureMonitoring System (TPMS) 106
Tire sealing system 108
Using the tire sealing system 110
Inflating a tire with the tire sealingsystem compressor 114
Electrical sockets 115
Replacing bulbs 116
Replacing low beam headlight bulbs 118
Replacing High Beam headlight bulbs 119
Replacing front parking light bulbs 120
Replacing front turn signal bulbs 120
Replacing the rear fog light 121
Bulb specifications 123
Replacing wiper blades 124
Windshield wipers in the service position 125
Refilling the windshield washer fluidreservoir 126
Opening and closing the hood 127

||
PRACTICAL INFORMATION
116
12-volt socket in the trunk
12-volt socket in the trunk
Fold down the cover to access the socket. Max. current provided is 10 A (120 W).
NOTE
The 12-volt socket in the trunk provides elec- trical current even when the ignition isswitched off. Using the socket while theengine is not running will drain the battery.
Related information
•Passenger compartment storage spaces (p. 80)
Replacing bulbs
The halogen headlight and rear fog light bulbs 8
can be replaced by the owner. Models with LED (Light Emitting Diode) head- lights: these lights must be replaced by a trainedand authorized Volvo service technician.
NOTE
Halogen headlights are not available on all models or in all markets. Consult your Volvo retailer if you are uncertain about the type of headlights in your vehicle.
NOTE
• For information regarding any bulbs not mentioned in this section, please contactyour Volvo retailer or a trained andauthorized Volvo service technician.
• Always switch off the ignition before star-ting to replace a bulb.
• If an error message remains in the dis-play after a faulty bulb has been replaced,contact an authorized Volvo workshop.
• Condensation may form temporarily onthe inside of the lenses of exterior lightssuch as headlights, fog lights, or taillights.This is normal and the lights aredesigned to withstand moisture. Normally,condensation will dissipate after thelights have been on for a short time.
• The optional Active Bending Light bulbscontain trace amounts of mercury. Thesebulbs should always be disposed of by atrained and qualified Volvo service techni-cian.
8
Halogen bulbs are not available on all models.

PRACTICAL INFORMATION
}}
* Option/accessory.117
CAUTION
Never touch the glass of bulbs with your fin- gers. Grease and oils from your fingers vapor-ize in the heat and will leave a deposit on thereflector, which will damage it.
WARNING
•The ignition should be switched off com- pletely (be in ignition mode
0) when
replacing bulbs.
• If the engine has been running just prior to replacing bulbs in the headlight hous-ing, please keep in mind that componentsin the engine compartment will be hot.
Before the halogen headlight bulbs can bereplaced, that plastic covering over the headlighthousing has to be removed and the housing hasto be lifted out of the vehicle.
–Release the pins in the plastic covering's four clips by pressing them down with ascrewdriver or similar object and remove thecovering.
NOTE
The pins in the clips have to be pressed back completely before the clips are placed in theplastic covering. When the covering is put back in place, the pins must be pressed so that their upper sur-face is flush with the surface of the clip.
Front bulbs (vehicles with halogen headlights)
Low beam
High beam
Parking light/Daytime Running Light
Turn signal
Fog light with corner illumination (LED) *

||
PRACTICAL INFORMATION
118
Taillight bulbs
Fog light9
Taillight (LED)
Turn signal
Side marker light (LED)
Brake light (LED)
Taillight (LED)
Backup light
10
High-mounted brake light (LED)
Related information
•
Replacing low beam headlight bulbs (p. 118)
• Replacing High Beam headlight bulbs (p. 119)
• Replacing front parking light bulbs (p. 120)
• Replacing front turn signal bulbs (p. 120)
• Replacing the rear fog light (p. 121)
• Bulb specifications (p. 123)
Replacing low beam headlight bulbs
On models with halogen headlights, the low beam headlight bulb can be replaced by theowner.
Before the bulb can be replaced, the plastic cov- ering over the headlight housing has to beremoved, see the article "Replacing bulbs."
CAUTION
Never touch the glass of bulbs with your fin- gers. Grease and oils from your fingers vapor-ize in the heat and will leave a deposit on thereflector, which will damage it.
9 Not available in all markets.
10 Must be replaced by a trained and qualified Volvo service technician.

PRACTICAL INFORMATION
119
Driver's side bulb housing shown
1. Remove the low beam round rubber coverfrom the headlight housing.
2. Remove the connector from the bulb.
3. Remove the bulb by pressing it slightly upward and then pulling it out.
4. Insert the bulb in the socket. The bulb's guid- ing pin should point straight up.
5. Press the connector into place.
6. Put the rubber cover back into place.
Related information
• Replacing bulbs (p. 116)
• Bulb specifications (p. 123)
Replacing High Beam headlight bulbs
On models with halogen headlights, the High Beam headlight bulb can be replaced by theowner.
Before the bulb can be accessed, the headlight housing's cover must be removed, see the article"Replacing bulbs."
CAUTION
Never touch the glass of bulbs with your fin- gers. Grease and oils from your fingers vapor-ize in the heat and will leave a deposit on thereflector, which will damage it.
Driver's side bulb housing shown
1. Remove the high beam round rubber cover from the headlight housing. 2. Remove the bulb by turning the bulb holder
upward and then pulling it straight out.
3. Carefully pry the plastic sleeve by the con- nector's locking lug to release it.
4. Remove the connector from the bulb.
5. Replace the bulb.
6. Position the bulb in the socket and turn it downward.
7. Put the rubber cover back into place.
Related information
• Bulb specifications (p. 123)
• Replacing bulbs (p. 116)

PRACTICAL INFORMATION
120
Replacing front parking light bulbs
On models with halogen headlights, the front parking light/Daytime Running Light bulb can bereplaced by the owner.
Before the bulb can be accessed, the headlight housing's cover must be removed, see the article"Replacing bulbs." Remove the high beam bulb first by turning the bulb holder upward and then pulling it straightout. This makes it easier to access the parkinglight bulb.
Driver's side bulb housing shown
1. Remove the rubber cover over the parking light bulb.
2. Pull the bulb holder straight out.
3. Remove the bulb by pulling it straight out.
4. Insert a new bulb. 5. Insert the bulb holder in the socket and
press it into place.
6. If the high beam bulb was removed, insert the bulb in the socket and turn downward.
7. Put the rubber cover back into position.
Related information
• Replacing bulbs (p. 116)
• Bulb specifications (p. 123)
Replacing front turn signal bulbs On models with halogen headlights, the front turn signal bulb can be replaced by the owner.
Before the bulb can be accessed, the headlight housing's cover must be removed, see the article"Replacing bulbs."
Driver's side headlight housing shown
1. Remove the rubber cover over the turn signal
bulb.
2. Press the retaining catches together and pull the bulb holder straight out.
3. The bulb holder and bulb must be replaced as one unit.
4. Press the new bulb holder into the socket.
5. Put the rubber cover back in place.

PRACTICAL INFORMATION
123
NOTE
When putting the plastic cover over the hinge back in place: •The pin in the clip must be pressed back far enough so that it sticks out of the clipbefore the clip is used to reinstall theplastic cover.
• When the hinge's plastic cover is put inposition, press the plastic clip into thehole in the cover.
• Press the pin into the plastic clip until itsend is flush with the surface of the clip.
1. Remove the bulb holder by turning it a quar-
ter turn counterclockwise and pulling it out.
2. Remove the defective bulb by pressing it in and turning it counterclockwise. 3. Insert a new bulb by pressing it in and turn-
ing it clockwise.
4. Wipe the new bulb with a clean cloth to remove any grease, etc.
5. Insert the bulb holder by turning it a quarter turn clockwise.
6. Put the panel and plastic cover over the hinge back in place in the reverse order.
NOTE
Rear fog lights are not available on all models or in all markets.
Related information
• Bulb specifications (p. 123)
Bulb specifications The following specifications apply to models equipped with halogen headlights 11
and rear fog
lights. If other bulbs need to be replaced, con- tact a trained and qualified Volvo service techni-cian.
Function [W]A
Type
Low beam 55 H11
High Beam 65 H9
Front turn signal 24 PY24WDaytime running light/ parking light 21/5 W21/5W
Rear fog light B
21 H21W LL
AWatt
B Rear fog lights are not available on all models or in all markets.
Related information
• Replacing bulbs (p. 116)