2018 TOYOTA C-HR Smart key system

4367-2. Steps to take in an emergency
C-HR_OM_USA_OM10526U
If the electronic key does not operate
properly (vehicles with a smart key system)
Use the mechanical key (→P. 100) in order to perform the following
operations:
Locks all the doors
Closes the windows (turn and
hold)
*
Unlocks the door
Turning the key rearward unlocks
the driver’s door. Turning the key
once again within 3 seconds
unlocks the other doors.
Opens the windows (turn and
hold)
*
*
: These settings must be customized at your Toyota dealer. ( →P. 474)
If communication between the electronic key and vehicle is
interrupted ( →P. 121) or the electronic key cannot be used
because the battery is depleted, the smart key system and
wireless remote control cannot be used. In such cases, the
doors can be opened and the engine can be started by follow-
ing the procedure below.
Locking and unlocking the doors

4377-2. Steps to take in an emergency
7
When trouble arises
C-HR_OM_USA_OM10526U
Ensure that the shift lever is in P and depress the brake pedal.
Touch the Toyota emblem side
of the electronic key to the
engine switch.
When the electronic key is
detected, a buzzer sounds and the
engine switch will turn to IGNITION
ON mode.
When the smart key system is
deactivated in customization set-
ting, the engine switch will turn to
ACCESSORY mode.
Firmly depress the brake pedal and check that and mes-
sages are shown on the multi-information display.
Press the engine switch.
In the event that the engine still ca nnot be started, contact your Toyota
dealer.
Starting the engine
1
2
3
4

4387-2. Steps to take in an emergency
C-HR_OM_USA_OM10526U
■Stopping the engine
Set the parking brake, shift the shift lever to P and press the engine switch as
you normally do when stopping the engine.
■ Replacing the key battery
As the above procedure is a temporary measure, it is recommended that the
electronic key battery be replaced immediately when the battery is depleted.
(→P. 373)
■ Changing engine switch modes
Release the brake pedal and press the engine switch in step above. The
engine does not start and modes will be changed each time the switch is
pressed. ( →P. 166)
■ When the electronic key does not work properly
●Make sure that the smart key system and push button start has not been
deactivated in the customization setting. If it is off, turn the function on.
(Customizable features: →P. 474)
● Check if battery-saving mode is set. If it is set, cancel the function.
(→P. 120)
WARNING
■ When using the mechanical key and operating the power windows
Operate the power window after checking to make sure that there is no pos-\
sibility of any passenger having any of their body parts caught in the side
window.
Also, do not allow children to operate the mechanical key. It is possible for
children and other passengers to get caught in the power window.
3

4407-2. Steps to take in an emergency
C-HR_OM_USA_OM10526U
Connect the jumper cables according to the following procedure:Connect a positive jumper cable clamp to the positive (+) battery
terminal on your vehicle.
Connect the clamp on the other e nd of the positive cable to the
positive (+) battery terminal on the second vehicle.
Connect a negative cable clamp to the negative (-) battery termi-
nal on the second vehicle.
Connect the clamp at the other end of the negative cable to a
solid, stationary, unpainted metallic point away from the battery
and any moving parts, as shown in the illustration.
Start the engine of the second v ehicle. Increase the engine speed
slightly and maintain at that level for approximately 5 minutes to
recharge the batter y of your vehicle.
Vehicles with a smart key system: Open and close any of the doors
of your vehicle with the engine switch off.3
32
4
4
5

4417-2. Steps to take in an emergency
7
When trouble arises
C-HR_OM_USA_OM10526U
Vehicles without a smart key system:
Maintain the engine speed of the second vehicle and turn the
engine switch to the “ON” position, then start the vehicle’s engine.
Vehicles with a smart key system:
Maintain the engine speed of the second vehicle and turn the
engine switch to IGNITION ON mode, then start the vehicle’s
engine.
Once the vehicle’s engine has started, remove the jumper cables in
the exact reverse order from which they were connected.
To install the engine cover, conduct the removal procedure in
reverse. After installing, check that the fixed pins are inserted
securely.
Once the engine starts, have the v ehicle inspected at your Toyota
dealer as soon as possible.
■ Starting the engine when the battery is discharged
The engine cannot be started by push-starting.
■ To prevent battery discharge
●Turn off the headlights and the air conditioning system while the engine is
stopped.
● Turn off any unnecessary electrical components when the vehicle is running
at a low speed for an extended period, such as in heavy traffic.
■ Charging the battery
The electricity stored in the battery will discharge gradually even when the
vehicle is not in use, due to natural discharge and the draining effects of cer-
tain electrical appliances. If the vehicle is left for a long time, the battery may
discharge, and the engine may be unable to start. (The battery recharges
automatically during driving.)
■ When exchanging the battery
●Use a battery that conforms to European regulations.
● Use a battery that the case size is same as the previous one (LN2), 20 hour
rate capacity (20HR) is equivalent ( 60Ah) or greater, and performance rating
(CCA) is equivalent (520A) or greater.
• If the sizes differ, the battery cannot be properly secured.
• If the 20 hour rate capacity is low, even if the time period where the vehi- cle is not used is a short time, the battery may discharge and the engine
may not be able to start.
● For details, consult your Toyota dealer.
6
7
8

4768-2. Customization
C-HR_OM_USA_OM10526U■
Instrument cluster (
→P. 92)
■Smart key system* and wireless remote control ( →P. 105, 118)
*: If equipped
FunctionDefault settingCustomized
setting
Sensor sensitivity for dark-
ening the brightness of the
instrument cluster
depending on the outside
brightness
Standard-2 to 2—O
Sensor sensitivity for
returning the brightness of
the instrument cluster to
the original level depend-
ing on the outside bright-
ness
Standard-2 to 2—O
FunctionDefault settingCustomized setting
Operation signal (buzzer)5
Off
—O
1 to 7
Operation signal (emer-
gency flashers)OnOff—O
Unlocking operation
Driver’s door
unlocked in one step, all doors
unlocked in two step
All doors unlocked
in one step—O
Time elapsed before the
automatic door lock func-
tion is activated if a door is
not opened after being
unlocked
60 seconds
30 seconds
—O
120 seconds
Open door reminder
buzzer (When locking the
vehicle)
OnOff—O
Locking operation when
door openedOnOff—O

4778-2. Customization
8
Vehicle specifications
C-HR_OM_USA_OM10526U■
Smart key system* (
→ P. 1 1 8 )
*: If equipped
■
Wireless remote control ( →P. 105)
■Outside rear view mirrors ( →P. 137)
FunctionDefault settingCustomized
setting
Smart key systemOnOff—O
Smart door unlockingDriver’s doorAll the doors—O
Number of consecutive
door lock operations2 timesAs many as desired—O
FunctionDefault settingCustomized
setting
Wireless remote controlOnOff—O
FunctionDefault settingCustomized setting
Automatic mirror folding
and extending operationLinked to the
locking/unlocking of the doorsOff—O
Linked to opera-
tion of the engine switch
—O

4788-2. Customization
C-HR_OM_USA_OM10526U■
Power windows (
→P. 140)
*1: Vehicles without a smart key system
*2: Vehicles with a smart key system
■
Turn signal lever ( →P. 176)
■Automatic light control system ( →P. 185)
FunctionDefault settingCustomized
setting
Key*1 or mechanical
key
*2 linked operation
(open)OffOn—O
Key*1 or mechanical
key
*2 linked operation
(close)OffOn—O
Wireless remote control
linked operation (open
only)
OffOn—O
Key*1 or mechanical
key
*2, wireless remote
control linked operation
signal (buzzer)OnOff—O
FunctionDefault settingCustomized
setting
Times of flashing of the
lane change signal flash-
ers
3
Off
—O5
7
FunctionDefault settingCustomized setting
Light sensor sensitivity Level 0 Level -2 to 2—O
Time elapsed before
headlights automatically
turn off after doors are
closed
30 seconds
Off
—O60 seconds
90 seconds