33
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
AHB is a safety system designed to help drivers see more of what’s ahead at
nighttime without dazzling other drivers. When enabled, AHB uses an in-vehicle
camera to help detect the headlights of oncoming vehicles and tail lights of
preceding vehicles, then automatically switches between high and low beams
as appropriate to provide the most light possible and enhance forward visibility.
By using high beams more frequently, the system may allow earlier detection of
pedestrians and obstacles.
Refer to a Toyota Owner’s Manual for additional information on AHB operation,
settings adjustments, limitations, and precautions before attempting to use it.
Automatic High Beams (AHB)
(1) With the engine switch in IGNITION ON mode, turn the headlight switch to
“AUTO” position.
(2) Push lever away from you.
The AHB indicator will come on when the headlights are turned on automatically
to indicate that the system is active.
Note: Pull the lever back toward you to turn the AHB system off.
The AHB indicator will turn off. To turn switch to “
” position and the manual
high beam indicator “
” turns on.
When all of these conditions are met, high beams will be automatically turned on
(after approximately 1 second):
t 7 F I J D M F T Q F F E J T B C P W F B Q Q S P Y J N B U F M Z N Q I L N I
t 5 I F B S F B B I F B E P G U I F W F I J D M F J T E B S L
t 5 I F S F B S F O P P O D P N J O H P S Q S F D F E J O H W F I J D M F T X J U I I F B E M J H I U T P S U B J M M J H I U T
turned on.
t 5 I F S F B S F G F X T U S F F U M J H I U T P O U I F S P B E B I F B E
If any of these conditions occur, the system is designed to automatically turn off
high beams:
t 7 F I J D M F T Q F F E E S P Q T C F M P X B Q Q S P Y J N B U F M Z N Q I L N I
t 5 I F B S F B B I F B E P G U I F W F I J D M F J T O P U E B S L
t 0 O D P N J O H P S Q S F D F E J O H W F I J D M F T I B W F I F B E M J H I U T P S U B J M M J H I U T
turned on.
t 5 I F S F B S F N B O Z T U S F F U M J H I U T P O U I F S P B E B I F B E
" $ 5 * 7 " 5 * / ( 5 ) & " ) # 4 : 4 5 & .
<00240030002f0025002a0035002a0030002f0034000300380029002600330026000300220029002300030038002a002d002d0003003500360033002f00030030002f001000300027002700030022003600350030002e00220035002a00240022002d002d00
3a0003>
(1) (2)
37
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
Pull up
Trunk-Internal release
Tire Pressure Monitoring (warning) System (TPMS)
System reset initialization
1. Push and hold “
SET” button until the indicator blinks three times.
2. Wait a few minutes to allow initialization to complete.
The tire pressure detected by the tire pressure warning system can
be displayed on the Multi-Information Display.
After adjusting tire pressures, or after tires have been rotated or replaced, turn
the “POWER” switch to IGNITION ON mode and press and hold the “
SET”
button until indicator blinks three times. Let the vehicle sit for a few minutes to allow
initialization to complete.
Refer to the load label on the door jamb or the Owner’s Manual for tire inflation
specifications.
If the tire pressure indicator flashes for more than 60 seconds and then remains on,
take the vehicle to your local Toyota dealer.
NOTE: The warning light may come on due to temperature changes or
changes in tire pressure from natural air leakage. If the system has not been
initialized recently, setting the tire pressures to factory specifications should
turn off the light.
