2018 SUZUKI JIMNY steering

Auto-on headlight system
78RB02093
The auto-on headlight system automati­cally _turns on all lights that are operated by the lighting control lever on the steering column, when the following three condi­tions are all met.
Conditions for auto-on headlight system operation: 1) It is dark around the light sensor (5). 2) The lighting control lever is in "AUTO"
position. 3) The ignition switch is in the "ON" posi-tion.
This. system is activated by a signal from the light sensor (5) on the passenger side of instrument panel. Do not cover the sen­sor (5). Otherwise, the system will not work
correctly.
A WARNING
It takes about 5 seconds for the light sensor to react to a change in light­ing conditions. To help avoid an acci­dent due to reduced visibility, turn on your headlights before driving into a tunnel, parking structure, etc.
NOTE: The light sensor reacts even to infrared rays, so it may operate incorrectly when there are strong infrared rays.
BEFORE DRIVING
Light reminder buzzer
The interior buzzer continuously beeps if you open the driver's door without turning off the headlights and position lights. This function is triggered under the following condition: The headlights and/or position lights are on even after the ignition switch is turned
off.
The buzzer stops sounding when you turn off the headlights and position lights.
NOTE: A message is indicated on the information display in the instrument cluster while the buzzer is sounding.
Daytime running light (D.R.L.) sys­
tem
Whe_n th_e engine is started, the daytime running lights are turned on by this system.
Conditions for D.R.L. system operation 1) The engine is running. 2) Headlights and front fog light (if equipped) are off.
NOTE: Brightness of the daytime running lights is different from the brightness of the position lights, but it is not a malfunction.
2-58

Turn signal control lever
57L21128
A WARNING
To avoid possible injury, do not oper­ate controls by reaching through the steering wheel.
Turn signal operation
With the ignition switch in "ON" position. move the lever upward or downward to activate the right or left turn signals.
Normal turn signal
68PM00234
Move the lever all the way upward or downward to signal. When the turn is com­pleted, the signal will cancel and the lever will return to its normal position.
BEFORE DRIVING
Lane change signal
68PM00235
Move the lever partially upward or down­ward to turn right or left and hold the lever in the moved position. The turn signal and its indicator fiash while the lever is held at the moved posi­tion. The turn signal and its indicator fiash 3 times even if you returned the lever immediately after the activation.
NOTE: The turn signal and its indicator can be set whether they flash 3 times after the turn signal lever is returned via the information display. Refer to "Information display" in this section.
2-66

BEFORE DRIVING
NOTE: You can customize the setting for the num-Hazard warning switch ber of flashing times of the turn signal and its indicator (1 to 4 times). Ask a SUZUKI deafer for the customization.
2-67
78RB02058
Push the hazard warning switch to activate the hazard warning lights. All turn signal lights and both turn signal indicators will flash simultaneously. To turn off the lights, push the switch again. Use the hazard warning lights to warn other drivers of possible risk of traffic haz­ard when you park your vehicle in case of emergency.
Windshield wiper and washer
lever
650611
A WARNING
To avoid possible injury, do not oper­ate controls by reaching through the steering wheel.

Tilt steering lock lever
(1) LOCK (2) UNLOCK
The lock lever is located under the steering column. To adjust the steering wheel height:
1) Push down the lock lever to unlock the steering column. 2) Adjust the steering wheel to the desired height and lock the steering column by pulling up the lock lever. 3) Try moving the steering wheel up and down to check that it is securely locked in position.
A. WARNING
Never attempt to adjust the steering wheel while the vehicle is moving or you could lose control of the vehicle.
BEFORE DRIVING
Horn
~
78RB02063
Press the horn button of the steering wheel to sound the horn. The horn will sound with the ignition switch in any position.
2-70

Engine oil consumption
It is normal for the engine to consume some engine oil during normal vehicle operation.
The amount of engine oil consumption depends on viscosity and quality of the oil and your driving conditions. More oil is consumed during high-speed driving and when there is frequent acceler­ation and deceleration. Under high loads, your engine also will consume more oil. A new engine also consumes more oil, since its pistons, piston rings and cylinder walls have not yet become conditioned. New engines reach the normal level of oil consumption only after approximately 5000 km (3000 miles) driving.
Oil consumption: Max. 1.0 L per 1000 km (1 Qt. per 600 miles)
When judging the amount of oil consump­tion, note that the oil may become diluted and it is difficult to judge the accurate oil level. As an example, if a vehicle is used for repeated short trips, and consumes a nor­mal amount of oil, the dipstick may not show any drop in the oil level at all, even after 1000 km (600 miles) or more of driv­ing. This is because the oil gradually becomes diluted with fuel or moisture,
making it appear that the oil level has not changed. You should also be aware that the diluting ingredients evaporate out when the vehicle is subsequently driven at high speeds, such as on an expressway, making it appear that oil is excessively consumed after high-speed driving.
OPERATING YOUR VEHICLE
Ignition switch
650611
A WARNING
To avoid possible injury, do not oper­ate controls by reaching through the steering wheel.
3-2

OPERATING YOUR VEHICLE
68PH00310
The ignition switch has the following four positions:
LOCK This is the normal parking position. It is the only position in which the key can be removed.
3-3
Manual transmission
Turn to "LOCK"
60G033
Manual transmission vehicles You must push in the key to turn it to "LOCK" position. It locks the ignition, and prevents normal use of the steering wheel after the key is removed.
Automatic transmission vehicles The gearshift lever must be in "P" (Park) position to turn the key to "LOCK" posi­tion. It locks the ignition and prevents normal use of the steering wheel and gearshift lever.
To release the steering lock, insert the key and turn it clockwise to one of the other positions. If you have trouble turning the key to unlock the steering wheel, try turn­ing the steering wheel slightly to the right or left while turning the key.
ACC Accessories such as the radio can oper­ate, but the engine is off.
ON This is the normal operating position. All electrical systems are on.
START This is the position for starting the engine using the starter motor. The key should be released from this position as soon as the engine starts.
Ignition key reminder A buzzer sounds intermittently to remind you to remove the ignition key if it is in the ignition switch when the driver's door is opened.

A. WARNING
Never return the ignition switch to "LOCK" position and remove the ignition key while the vehicle is moving. The steering wheel will lock and you will not be able to steer the vehicle. (Continued)
A. WARNING
(Continued) Always return the ignition switch to "LOCK" position and remove the ignition key when leaving the vehi­cle even only for a short time. Also do not leave children alone in a parked vehicle. Unattended chil­dren may be able to start the vehi­cle or shift the transmission into neutral, which could result in an accident. There is also a danger that children may injure them­selves by playing with the power windows or other moving features of the vehicle. In addition, heat build-up or extremely cold tem­peratures inside the vehicle can be fatal to children.
OPERATING YOUR VEHICLE
NOTICE
For protection of a lead-acid bat­tery and a starter motor, do not use the starter motor by turning the key to "START" for more than 12 sec­onds at a time. If the engine dose not start, turn the key to "LOCK" position and wait for more than 30 seconds before trying again. If the engine does not start after several attempts, consult a SUZUKI dealer or a qualified workshop. Do not leave the ignition switch in "ON" position if the engine is not running as the lead-acid battery will discharge.
3-4

OPERATING YOUR VEHICLE
Parking brake lever
(1) To set (2) To release (3) To release
The parking brake lever is located between the front seats. To set the parking brake, depress the brake pedal and pull the park­ing brake lever all the way up. To release the parking brake, depress the brake pedal and pull up slightly on the parking brake lever, push the button on the end of the lever with your thumb, and lower the lever to its original position.
3-5
For automatic transmission vehicles, always set the parking brake before mov­ing the gearshift lever to "P" (PARK) posi­tion. If you park on an incline and shift into "P" before setting the parking brake, the weight of the vehicle may make it difficult to shift out of "P" when you are ready to drive the vehicle.
When preparing to drive the vehicle, move the gearshift lever out of "P" position before releasing the parking brake.
A WARNING
• Whenever parking, make sure the gearshift lever for manual trans­mission vehicles is in 1st gear or "R" (Reverse) and the gearshift lever for automatic transmission or automatic transmission vehicles is in 11P" {Park). Remember, even though the transmission is in gear or in Park, you must set the parking brake fully. • When parking on an uphill, turn the steering wheel so that the front wheels point to the center of the
road. • When parking on a downhill, turn the steering wheel so that the front wheels point to the curb. • Never drive your vehicle with the parking brake on: rear brake effec­tiveness can be reduced from overM heating, brake life may be shortened, or permanent brake damage may result. • If the parking brake does not hold the vehicle securely or does not fully release, have your vehicle inspected immediately by a SUZUKI dealer.