2018 SUBARU BRZ brake rotor

164 2-1. Driving procedures
BRZ_U (A4450BE-A)
WARNING
■When driving on slippery road surfaces
●Sudden braking, acceleration and steering may cause tire slippage and
reduce your ability to control the vehicle, resulting in an accident.
● Sudden acceleration, engine braking due to shifting, or changes in engine
speed could cause the vehicle to skid, resulting in an accident.
● After driving through a puddle, lightly depress the brake pedal to make
sure that the brakes are functioni ng properly. Wet brake pads may prevent
the brakes from functioning properly. If the brakes on only one side are wet
and not functioning properly, steering control may be affected, resulting in
an accident.
■ When shifting the select lever or shift lever
●On vehicles with an automatic transmission, be careful not to shift the
select lever with the accelerator pedal depressed. Shifting the select lever
to a gear other than P or N may lead to unexpected rapid acceleration of
the vehicle that may cause an accident and result in death or serious
injury.
● Do not place items in the select lever’s or shift lever’s surrounding area. It
may cause incorrect operation.
● If the select lever’s or shift lever’s boot is pulled out during cleaning, return
it to its previous position. If the select lever’s or shift lever’s boot is left
pulled out, the select lever or shift lever may become difficult to operate.
■ If you hear a squealing or scrapin g noise (brake pad wear limit indica-
tors)
Have your SUBARU dealer check and replace the brake pads as soon as
possible.
Rotor damage may result if the pads are not replaced when needed.
It is dangerous to drive the vehicle when the wear limits of the brake pads
and/or those of the brake discs are exceeded. ( →P. 159)
■ Breaking-in of new brake pads and linings
A safe location and situation should be selected for break-in driving.

170 2-1. Driving procedures
BRZ_U (A4450BE-A)
CAUTION
■Avoiding damage to vehicle parts
●Do not turn the steering wheel fully in either direction and hold it there for
an extended period of time.
Doing so may damage the power steering motor.
● When driving over bumps in the road, drive as slowly as possible to avoid
damaging the wheels, underside of the vehicle, etc.
● On vehicles with an automatic transmission, do not race the engine for
more than 5 seconds in any position except the N or P position when the
brake is applied or when chocks are used in the wheels. This may cause
the transmission fluid to overheat.
■ Avoiding damage to the under spoilers (tS models)
On vehicles with under spoilers, be careful when driving, as the ground
clearance will be lower than a vehicle without them as follows:
●Front under spoiler: Ground clearance at the front of each front wheel arch
and the center of the front bumper is lower by approximately 0.4 in. (1 cm)
and 1.6 in. (4 cm), respectively.
● Side under spoilers: Ground clearance at the sides of the vehicle is lower
by approximately 1.2 in. (3 cm).
● Rear under spoilers: Ground clearance at each corner of the rear bumper
is lower by approximately 0.4 in. (1 cm).
■ Replacement of brake pad and lining
If you continue to drive despite the scraping noise from the audible brake
pad wear indicator, it will result in the need for costly brake rotor repair or
replacement.
■ Breaking-in of new brake pads and linings
Pulling the parking brake lever too forcefully may cause the rear wheels to
lock. To avoid this, be certain to pull the lever up slowly and gently.

338 4-1. Maintenance and care
BRZ_U (A4450BE-A)
■Brake (vehicles with brembo brake)
●Painted brake calipers
• When using detergent, use neutral detergent. Do not use hard brushes
or abrasive cleaners, as they will damage the paint.
• Do not use detergent on the brake calipers when they are hot.
• Wash detergent off immediately after use.
● Rust may form if the vehicle is parked with wet brake pads or disc rotors,
causing them to stick. Before parking the vehicle after it is washed, drive
slowly and apply the brakes several times to dry the parts.
■ CFRP (Carbon Fiber Reinforced Plastic) part (if equipped)
●Remove any dirt using a neutral detergent. Do not use hard brushes or
abrasive cleaners. Do not use st rong or harsh chemical cleaners.
● As the CFRP parts may change color if they are exposed to ultraviolet
rays for extended periods of time, SUBARU recommends that your vehi-
cle be stored in a place where it will not be exposed to direct sunlight.
● Do not use wax that contains abrasives.
■ When washing the vehicle
Wear rubber gloves and use a hand brush when washing down underbody,
inner fenders and suspension to effectively remove mud and dirt off.