2018 Seat Tarraco display

Infotainment System
Function button: function
Position : current vehicle position in coordinates and
GPS stat us (sat
ellite reception). a)
This function button is only shown when route guid-
ance is not active or when pr edictiv

e route guidance
is active.
Press the  function button to close the split
screen.
At any moment during navigation, pr essing
inside the map will mak

e a pop-up menu ap-
pear with the following functions: Function button: function
Street name or coordinates : shows the details of the
point select ed on the map

.
Only when you press on an icon on the map:
POI : name of the point of interest (when only one
appears on the map).
Group of POIs : more points of interest (when you
press on the map on v arious POIs gr

ouped to-
gether).
Favourite : name of the favourite.
Home : Home address.
Start route guidance : starts guidance directly.
Add stopover destination : only when you have an ac-
tive r out

e.
Search nearby : enters in the search menu, but only
for the ar ea ar

ound the point selected on the map. Function button: function
Demo mode start (only when demo mode is active)
Map display
Fig. 227
Messages and function buttons on
the map displ ay. Function buttons and messages on the
map displ
ay.
T o activ

ate function buttons

Infotainment System
Only 3 of these items of information can be
displ ayed at the same time
, but the user
chooses which t
o display, and in what order,
by moving the finger vertically over the dials.
Press the Next  button to display the L
ap
timer menu 1)
.
Offr

oad*
If the corresponding equipment is available,
the information that appears is the following:
Compass.
Turning angle of steered wheels.
Coolant temperature.
Lubricating oil temperature
Only 2 of these items of information can be
displayed at the same time, but the user
chooses which to display, and in what order,
by moving the finger vertically over the dials.
Consumers
By pressing the CONSUMERS button, informa-
tion on the st atus of the v

ehicle

Operating modes
Display and symbols of the tele-
phone management syst emFig. 237
Active call. Display: Meaning

Driving
speed without slowing the engine below its
idling speed.
Aft er st
arting the descent of a sl
ope below
30 km/h (18 mph), speed is limited to a mini-
mum of 2 km/h (1 mph) and a maximum of
30 km/h (18 mph). When appropriate, the
driver may increase or decrease the speed
within the limit by pressing the accelerator or
the brake. At this point the function is interrup-
ted and, if necessary, it is then reactivated.
Even so, it is imperative that the surface guar-
antees sufficient adhesion. For this reason,
the Hill Descent Control will not fulfil its func-
tion when, for example, descending a slope
with a frozen or slippery surface.
Hill Descent Control is available when the
dash panel display shows the message k.
Hill Descent Control automatically intervenes
if the following conditions are met:

Driving
Safety distance warning
If the syst em det
ects a sit
uation of danger
because the vehicle is too close to the vehicle
ahead, it will warn the driver by means of an
indication on the instrument panel display

Driving
Trailer mode
When driving with tr ail
er the ACC contr
ols
less dynamically.
Overheated brakes
If the brakes overheat, for example after
abrupt braking or in long and steep slopes,
the ACC may be deactivated temporarily.
The relevant text message will appear in the
dash panel display. In this case, adaptive
cruise control cannot be activated.
Adaptive Cruise Control can be reactivated
once brake temperature has cooled suffi-
ciently. The message will disappear from the
instrument panel display. If the message ACC
not available remains on for quite a long
time it means that there is a fault. Contact a
specialised workshop. SEAT recommends vis-
iting a SEAT dealership. WARNING
If you do not heed the Press the brake
message, the v ehicl

e may initiate an invol-
untary movement and could crash into the
vehicle ahead. In any event, before driving
off, check that the road is clear. The radar
sensor may not detect obstacles on the
road. This could cause an accident and se-
rious injuries. If necessary, apply the brake. Lane Assist system*
Intr oduction Fig. 270
On the windscreen: field of vision of
the L ane Assist syst
em camer

a. Using the camera located in the windscreen,
the L
ane Assist syst
em det

ects the possible
lines dividing the lanes. When the vehicle in-
voluntarily approaches a dividing line it has
detected, the system notifies the driver with a
corrective steering movement. The purpose is
not only to warn the driver, but also to keep
the vehicle inside the lane. This movement
can be over-regulated at any time.
No warning is produced with the turn signals
activated, given that the Lane Assist system
understands that a lane change is required.
As soon as the ignition is switched on, the
lane departure function is automatically acti-
vated. Control lamp "
It lights up yellow
Lane Assist active but not available.
The system cannot accurat
ely recognise the lane.
Please see page 294, Lane Assist system is not avail-
able (the control lamp is lit up yellow). "
It lights up green
Lane Assist system active and available. Some control and warning lamps will light up
briefly when the ignition is s
wit
ched on t

o
check certain functions. They will switch off
after a few seconds. WARNING
Observe the safety warnings

Driver assistance systems
Indications on the instrument panel
displ ay Fig. 271
On the instrument panel display: Indi-
cation on the L ane Assist system displ
ay (ex-
ample 1). Fig. 272
On the instrument panel display: Indi-
cation on the L ane Assist syst
em displ

ay (ex-
ample 2). Status display
Fig. 27 1


: The system is active, but not
available, either because the minimum
speed has not been reached or because
the lane lines are not recognised.
Fig. 271 : The system is active and available, both lane lines are recognised.
The steering angle is not being correc-
ted at this moment.

Driver assistance systems
Using the blind spot detector (BSD)
with parking assist ant (RC
T
A)Activating and deactivating the blind spot
detect
or (BSD) with parking assist

ant
(RCTA)
The blind spot detector with parking assistant
can be switched on and off by accessing the
Assistance systems menu on the dash
panel display using the steering wheel con-
trols. If the vehicle is equipped with a multi-
function camera, it can also be accessed by
means of the driver assistance systems key
located on the main beam headlight lever.
Open the Assistants menu.