2018 Seat Ibiza brake

The essentials
The anti-theft wheel bolt has a diff er
ent
cap . This cap only fits on anti-theft locking
bolts and is not for use with standard wheel
bolts.
Important information about wheel bolts
Factory-fitted rims and wheel bolts are spe-
cially matched during construction. There-
fore, if different rims are fitted, the correct
wheel bolts with the right length and heads
must be used. This ensures that wheels are
fitted securely and that the brake system
functions correctly.
In certain circumstances, you should not even
use wheel bolts from vehicles of the same
model.
In wheels with full hubcaps, the anti-theft
locking bolt must be threaded onto positions

Emergencies
Side turn signals Fig. 110
Turn signal integrated in the rear view
mirr or The side turn signals are LEDS and are inte-
gr
at
ed in the r
ear view mirrors.
In case of failure, go to an authorised work-
shop to have it replaced.
Additional brake light Given the difficulty involved in the replace-
ment of this light it shoul
d be done by Techni-
cal Services. Changing the int

erior bulbs
Interior light and front r
eading
lights Fig. 111
Front reading light. To remove the glass

Operation
Note
The storage drawer will hold a maximum
weight of 1.5 k g.Storage pocket in the seat*
Fig. 157
Storage pocket. There is a storage pocket on the rear of the
fr
ont seats.
St or
age compartment in front door
panel* In this storage compartment a 1.5l water bot-
tl
e, et

c. can be stored. Front drink holder*
Fig. 158
Front drink holders in the centre con-
sol e. In the central console, next to the hand brake,
ther
e ar
e tw

o drinks holders

Driving
away. Always apply the handbrake when you
l eav
e your v
ehicle and when you park.
Applying the handbrake

Driving
Electronic differential lock (EDS)* The EDL operates along with the ABS in vehi-
cles equipped with El
ectr
onic Stability Con-
trol (ESC)*.
EDL helps the vehicle to start moving, accel-
erate and climb a gradient in slippery condi-
tions where this may otherwise be difficult or
even impossible.
It uses the ABS sensors to monitor the speed
of the driven wheels.
At speeds of up to approximately 80 km/h
(50 mph), it is able to balance out differences
in the speed of the driven wheels of approxi-
mately 100 rpm/min caused by a partially
slippery road surface. It does this by braking
the wheel which has lost traction and distrib-
uting more driving force to the other driven
wheel via the differential.
To prevent the disc brake of the braking
wheel from overheating, the EDL cuts out au-
tomatically if subjected to excessive loads.
The vehicle will continue to function normally
without EDL. For this reason, the driver is not
informed that the EDL has been switched off.
The EDL will switch on again automatically
when the brake has cooled down. Control lamp
A malfunction in the EDL is indicated by the
ESC contr ol l

amp . Take the vehicle to a
specialised workshop as soon as possible. WARNING

Start and driving
vehicle to a specialised workshop as soon as
possibl e
.
If ther
e is a fault in the ABS, the ESC* and the
tyre pressure control lamp will also light up.
Brake system fault
If the ABS warning lamp  lights up together with the brake warning lamp , there is a
fault in the ABS function and in the brake sys-
tem

Driving
Electronic torque management
(XDS)* When taking a curve, the driveshaft differen-
tial mechanism allo
ws the out
er wheel to turn
at a higher speed than the inner wheel. In this
way, the wheel that is turning faster (outer
wheel) receives less drive torque than the in-
ner wheel. This may mean that in certain sit-
uations the torque delivered to the inner
wheel is too high, causing the wheels to spin.
On the other hand, the outer wheel is receiv-
ing a lower drive torque than it could transmit.
This causes an overall loss of lateral grip on
the front axle, resulting in understeer or
“lengthening” of the trajectory.
The XDS system can detect and correct this
effect via the sensors and signals of the ESC.
Via the ESC, the XDS will brake the inside
wheel and counter the excess driving torque
of that wheel. This means that the driver

Start and driving
The system maintains brake pressure for ap-
pr o
ximat
ely two seconds after the driver
takes his foot off the brake pedal to prevent
the vehicle from lurching backward when it is
started. During these 2 seconds, the driver
has enough time to release the clutch pedal
and accelerate without the vehicle moving
and without having to use the handbrake,
making start-up easier, more comfortable
and safer.
These are the basic operation conditions: