2018 Seat Alhambra battery capacity

The essentials
starting, check the magic eye on the battery
› ›
›
 page 283.
For starting assistance, jump lead cables con-
forming to the standard DIN 72553 are re-
quired (see the cable manufacturer instruc-
tions). The jump lead cable must be at least
25 mm 2
in section (0,038 inches 2
) for petrol
engines, and 35 mm 2
(0,054 inches 2
) for die-
sel engines.
For vehicles whose battery is not in the en-
gine compartment, the jump leads should
only be connected to the starting assistance
connection points in the engine compart-
ment. WARNING
Incorrect use of jump leads and incorrectly
jump st ar

ting could cause the battery to ex-
plode resulting in serious injury. Please ob-
serve the following rules to minimise the risk
of a battery explosion:
● The battery providing current must have
the same v
oltage (12V) and approximately
the same capacity (see markings on battery)
as the flat battery.
● Never charge a frozen or recently thawed
batter
y. A flat battery can also freeze at tem-
peratures close to 0°C (+32°F).
● If a battery is frozen and/or has been frozen
then it mus
t be replaced.
● A highly explosive mixture of gases is re-
lea
sed when the battery is being charged. Al- ways keep lit cigarettes, flames, sparks and
fire f
ar fr

om the battery. Never use a mobile
telephone when connecting and removing the
jump leads.
● Charge the battery only in well ventilated
area
s given that when the battery is charged
by outside assistance, it creates a mix of
highly explosive gases.
● Jump leads should never enter into contact
with mov
ing parts in the engine compart-
ment.
● Never switch the positive and negative
pole
s or connect the jump leads incorrectly.
● Note the instruction manual provided by
the manufact
urer of the jump leads. CAUTION
To avoid considerable damage to the vehicle
electric a

l system, note the following careful-
ly:
● If the jump leads are incorrectly connected,
this c
ould result in a short circuit.
● The vehicles must not touch each other,
otherwi
se electricity could flow as soon as
the positive terminals are connected. Positive pole on the jump lead con-
nection point
s Fig. 73
In the engine compartment: positive
po l
e f

or starting assistance + .
On some vehicles, there is a starting assis-
t
anc
e t

erminal in the engine compartment,
under a labelled cover. 53

The essentials
How to jump start: description Fig. 74
Diagram of connections for vehicles
w ithout

Start-Stop system. Fig. 75
Diagram of connections for vehicles
w ith
St

art-Stop system. Jump lead terminal connections
Swit
c

h off the ignition of both vehicles
››› .
1. Connect one end of the
re
d
jump lead to
the positive + terminal of the vehicle
w ith the fl
at
battery A
› ››
Fig. 74
.
C
onnect the other end of the red jump
lead to the positive terminal + in the
v ehic
l

e providing assistance B .
F or

vehicles without Start-Stop system:
connect one end of the black jump lead
to the negative terminal – of the vehi-
c l
e pr

oviding the current B
› ››
Fig. 74
.
F
or vehicles with Start-Stop system: con-
nect one end of the black jump lead X to a suitable ground terminal, to a solid
piec
e of
met

al in the engine block, or to
the engine block itself ››› Fig. 75.
Connect the other end of the black jump
lead X to a solid metal component bol-
t ed t
o the en

gine block or to the engine
block itself of the vehicle with the flat
battery. Do not connect it to a point near
the battery A .
P o
s

ition the leads in such a way that
they cannot come into contact with any
moving parts in the engine compart-
ment.
Starting Start the engine of the vehicle with the
boosting battery and let it run at idling
speed.
2.
3.
4a.
4b.
5.
6.
7.
Start the engine of the vehicle with the
flat b

attery and wait for 2 or 3 minutes
until the engine is running.
Removing the jump leads Before you remove the jump leads,
switch off the dipped beam headlights if
they are switched on.
Turn on the heater blower and heated
rear window in the vehicle with the flat
battery. This helps minimise voltage
peaks which are generated when the
leads are disconnected.
When the engine is running, disconnect
the leads in reverse order to the details
given above.
Make sure the battery clamps have sufficient
metal-to-metal contact with the battery termi-
nals.
If the engine fails to start after about 10 sec-
onds, switch off the starter and try again after
about 1 minute. WARNING
● Ple a

se note the safety warnings referring to
working in the engine compartment
›››  page 271.
● The battery providing assistance must have
the same v
oltage as the flat battery (12V) and
approximately the same capacity (see imprint
on battery). Failure to comply could result in
an explosion. 8.
9.
10.
11.
54

Operation
●
Unshiel ded equipment
can cause interfer-
ence on the radio equipment and the vehi-
cle's electrical system.
● Interference can occur on the radio's AM
wave
band if electrical appliances are used
near the rear window aerial. Vehicle power sockets
Fig. 192
Centre console, rear section: 12 volt
soc k
et Fig. 193
Rear centre console: 230 Volt Euro
pow er soc

ket Depending on your vehicle version, you may
h
av
e a 12-

volt power socket and/or a 230
volt power socket.
Maximum power consumption
Power sock-
etMaximum power consumption
12 Volts120 Watts
230 Volts150 Watts (300 Watt peak) The maximum capacity of each power socket
mu
s
t

not be exceeded. The power consump-
tion is indicated on the rating plate of each
appliance.
Where two or more appliances are connected
at the same time, the total rating of all the
connected devices must never exceed 190
Watts ››› .12 volt power socket
The 12
v
o

lt power socket will only work with
the ignition on.
Using electrical appliances with the engine
stopped and the ignition switched on will
drain the battery. Therefore, electrical devi-
ces connected to the power socket can only
be used when the engine is running.
To prevent voltage variations from causing
damage, switch off the electrical consumer
connected to the 12 volt power socket before
switching the ignition on or off and before
starting the engine.
12 volt power sockets can be found in the fol-
lowing locations in the vehicle:
● Compartment in the centre of the centre
conso
le.
● Compartment in the front centre console.
● Storage compartment in the front central
armres
t.
● Rear centre console ›››
Fig. 192.
● At the rear right of the luggage compart-
ment.
230 V

olt Euro power socket*
The power socket only works when the en-
gine is running ››› .
C onn e

cting an electrical appliance: plug the
device into the power socket as far as possi-
ble to unlock the built-in childproof lock. The
174

Checking and refilling levels
Windscreen washer reservoir Chec k
in
g and topping up the wind-
screen washer reservoir Fig. 248
In the engine compartment: wind-
s c
r

een washer reservoir top Read the additional information carefully
› ›
›

 page 42
Check the level in the windscreen washer
tank regularly and top up as required.
● Open the bonnet  ›››
page 271.
● The washer reservoir is marked with the 
symbol on the c
ap ››› Fig. 248.
● Check there is enough water in the reser-
voir.
● T

o top up, mix water with a window cleaner
recommended b
y SEAT ››› . Please follow
the in struction
s for use found on the packag-
ing. ●
In col
d weather, a special antifreeze should
also be added to prevent the water from
freezing ››› .
Fi l
lin

g amounts
The capacity of the tank is approximately 3 li-
tres; in vehicles with a headlight washer sys-
tem, it is approximately 7 litres. WARNING
Never mix an unsuitable antifreeze or other
simi l

ar additives with the windscreen washer
water. A greasy layer may be formed on the
windscreen which will impair visibility.
● Use clean water with a window cleaner rec-
ommended by
SEAT.
● If necessary, add a suitable antifreeze to
the water in the r
eservoir. CAUTION
● Do not mi x

cleaning products recommen-
ded by SEAT with other products. This could
lead to flocculation and may block the wind-
screen washer jets.
● When topping up service fluids, make abso-
lutely c
ertain that you fill the fluids into the
correct reservoirs. Using the wrong fluids
could cause serious malfunctions and engine
damage! Vehicle battery
Intr oduction The battery is a component of the vehicle's
electric
al

system.
Never work on the electrical system without
fully understanding the operations required,
the applicable safety standards and without
the correct tools ››› ! If required, have any
work c

arried out by a specialised workshop.
SEAT recommends taking your car in for tech-
nical service. Negligent work can cause seri-
ous injury.
Location and number of batteries in the vehi-
cle
The battery is located in the engine compart-
ment.
Explanation of the warning indications on
the vehicle's battery 
Wear eye protection!

Battery acid is extremely corrosive. Al-
ways wear protective gloves and eye pro-
tection!

Fires, sparks, open flames and smoking
are prohibited.

A highly explosive mixture of gases is re-
leased when the battery is under charge.»
283
Technical data
Advice
Operation
Emergencies
Safety

Index
identification number . . . . . . . . . . . . . . . . . . . . 297
lo a
din
g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
parking downhill . . . . . . . . . . . . . . . . . . . . . . . . 191
parking uphill . . . . . . . . . . . . . . . . . . . . . . . . . . 191
raising . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
vehicle identification number . . . . . . . . . . . . . 297
Vehicle battery . . . . . . . . . . . . . . . . . . . . . . . 42, 283 acid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
assisted starting . . . . . . . . . . . . . . . . . . . . . . . . . 52
automatically disconnecting devices . . . . . . . 286
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
checking the battery electrolyte level . . . . . . . 285
connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
control and warning lamps . . . . . . . . . . . . . . . 284
discharging . . . . . . . . . . . . . . . . . . . . . . . 183, 185
disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
disconnecting . . . . . . . . . . . . . . . . . . . . . . . . . . 285
positive terminal for starting assistance . . . . . . 53
preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
starting assistance . . . . . . . . . . . . . . . . . . . . . . . 54
Vehicle care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 airbag modules (dash panel) . . . . . . . . . . . . . 262
anodized surfaces . . . . . . . . . . . . . . . . . . . . . . 257
antenna incorporated in window . . . . . . . . . . . 263
chrome parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
cleaning wheels . . . . . . . . . . . . . . . . . . . . . . . . 257
dash panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
de-icing the door lock cylinder . . . . . . . . . . . . 258
engine compartment . . . . . . . . . . . . . . . . . . . . 258
exterior mirrors . . . . . . . . . . . . . . . . . . . . . . . . . 255
interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
plastic parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
protection of vehicle undercarriage . . . . . . . . 258
rubber seals . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
things to note . . . . . . . . . . . . . . . . . . . . . . . . . . 254 vehicle paintwork . . . . . . . . . . . . . . . . . . . . . . . 256
window
s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
wooden trim . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
Vehicle care products . . . . . . . . . . . . . . . . . . . . . . 253
Vehicle identification data vehicle data label . . . . . . . . . . . . . . . . . . . . . . . 297
Vehicle interior monitoring . . . . . . . . . . . . . . . . . 120
Vehicle key set . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Vehicle tool kit . . . . . . . . . . . . . . . . . . . . . . . . . 46, 83 components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Vehicle undercarriage guard . . . . . . . . . . . . . . . . . 57
Vehicle's battery running flat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Vibrations steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Voice control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
W Warning lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Warning triangle . . . . . . . . . . . . . . . . . . . . . . 83, 134
Washing the vehicle . . . . . . . . . . . . . . . . . . . . . . . 253 adhesive sheets . . . . . . . . . . . . . . . . . . . . . . . . 255
sensors . . . . . . . . . . . . . . . . . . . . . . . . . . 211, 215
things to note . . . . . . . . . . . . . . . . . . . . . 118, 254
Wax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Wear indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 292
Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
What negatively affects driving safety? . . . . . . . . 57
Wheel bolts . . . . . . . . . . . . . . . . . . . . . . . . . . 85, 299 anti-theft . . . . . . . . . . . . . . . . . . . . . . . . 46, 84, 85
caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
loosening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
tightening torque . . . . . . . . . . . . . . . . . . . . . . . . 48
Wheel load capacity . . . . . . . . . . . . . . . . . . . . . . . 294 Wheel rims
beadloc k . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
bolted trims . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
Wheels . . . . . . . . . . . . . . . . . . . . . . . . 287, 289, 299 changing a wheel . . . . . . . . . . . . . . . . . 46, 49, 85
hubcaps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Wheel trim hubcaps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Windows automatic operation . . . . . . . . . . . . . . . . . . . . . 127
automatic raising/lowering . . . . . . . . . . . . . . . 127
convenience closing . . . . . . . . . . . . . . . . . . . . . 127
convenience opening . . . . . . . . . . . . . . . . . . . . 127
electric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
malfunction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
removing ice . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
roll-back function . . . . . . . . . . . . . . . . . . . . . . . 128
Window wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Window wiper blade . . . . . . . . . . . . . . . . . . . . . . . . 27
Windscreen and rear window wiper blades . . . . . 88
Windscreen washer . . . . . . . . . . . . . . . . . . . 42, 137
Windscreen washer fluid control lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Windscreen washer water checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
topping up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Windscreen wiper . . . . . . . . . . . . . . . . . . . . . . . . . 137 heated windscreen washer jets . . . . . . . . . . . . 138
Window wiper lever . . . . . . . . . . . . . . . . . . . . . 137
Windscreen wipers . . . . . . . . . . . . . . . . . . . . . . . . . 27 functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
headlight washer system . . . . . . . . . . . . . . . . . 138
lifting the wiper blade . . . . . . . . . . . . . . . . . . . . 55
rain sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
replacing the wiper blade . . . . . . . . . . . . . . . . . 55
319