2018 Peugeot iOn reset

88
Ancillaries battery
All of the electrical components on your vehicle
(with the exception of the electric motor, the
heating and the air conditioning) are powered
by the ancillaries battery.
It is located in the front compartment under
the bonnet and is charged by the main battery
during phases of operation ("Ready" lamp on in
the instrument panel) and charging.If the ancillaries battery is discharged,
the electric motor cannot be started and
charging of the main battery is no longer
possible.
It is not recommended to disconnect the
battery.
However, during a prolonged period of
more than one month without using your
vehicle, it may be necessary, in winter,
to disconnect the battery and store it to
prevent the electrolyte freezing.
After prolonged disconnection of the
battery, you must consult a PEUGEOT
dealer or a qualified workshop in order to
have the electronic computer reset.
Access to the battery
F Open the bonnet using the interior release lever and then the exterior safety catch.
F

S
ecure the bonnet stay.
F

L
oosen the nut 1 .
F

R
emove the protective cover from the
battery for access to the two terminals.
Starting using another
battery
Make sure the electrolyte is not frozen.
Check the level and top up with distilled
water, if necessary.
For more information on Checking levels ,
refer to the corresponding section.
Ensure that the back-up battery is a 12
V
battery.
F

L
ift the protective cover from the (+)
terminal,
In the event of a breakdown

2
Select preset radio station.
Radio, press and hold: store a
station.
Other than radio: see the
corresponding sections.
Eject CD.
Select the source:
Radio: FM1, FM2, CD, USB, AUX,
Streaming.
Telephone: accept an incoming call.
Telephone, press and hold: end
a call, access the calls log for the
connected telephone.
Radio
Presetting a station
Press SRC/TEL repeatedly to select
the FM1, FM2 or AM waveband.
Press and hold a button to preset
the station being listened to. The
name of the station is displayed and
an audible signal confirms that it has
been preset. The external environment (hills, buildings,
tunnels, basement car parks, etc.) may
block reception, including in RDS tracking
mode. This is a normal effect of the way
in which radio waves are transmitted and
does not indicate any failure of the audio
equipment.
Selecting a station
Press a button to listen to the
corresponding preset station.
Managing a list
Press LIST
to display the list of
stations received in alphabetical
o r d e r.
Select the desired radio station
using one of the buttons.
Confirm with " OK".
Briefly press one of the buttons to
change to the next or previous letter.
Press and hold LIST to build or
update the list of stations; audio
reception is cut momentarily.
Entering a frequency
Press MENU .
Select "Radio ".
Select "Enter or Write freq. ".
Press + ,
or press – to select the desired
frequency.
Confirm with " OK".
RDS
RDS, if activated, allows you to
continue listening to the same station
by automatically retuning to alternative
frequencies. However, in certain conditions,
coverage of an RDS station may not be
assured throughout the entire country as
radio stations do not cover 100% of the
territory. This explains the loss of reception
of a station that can occur during a journey.
With source FM1 or FM2, press
MENU .
Select "Radio ".
Bluetooth® audio system

10
QUESTIONRESPONSESOLUTION
There is a difference in sound quality between
the different audio sources (radio, CD, etc.). For optimum sound quality, the audio settings
(volume, bass, treble, ambience, loudness)
can be adapted to the different sound sources,
which may result in audible differences when
changing source (radio, CD, etc.).Check that the audio settings (volume, bass,
treble, ambience, loudness) are adapted to
the sources being listened to. It is advisable to
set the AUDIO functions (bass, treble, front-
rear balance, left-right balance) to the middle
position, select the musical ambience and set
the loudness correction to the "Active" position
in CD mode or to the "Inactive" position in radio
mode.
When changing the settings for treble and bass,
the ambience setting is deselected.
When changing the ambience setting, treble
and bass are reset to zero. Choosing an ambience imposes settings for
treble and bass. Modifying one without the other
is only possible with a personalised ambience.
Modify the treble and bass settings or the
ambience setting to obtain the desired sound
quality.
When changing the balance setting, distribution
is deselected. Choosing the "driver" distribution setting
imposes a balance setting.Modify the balance or distribution settings to
obtain the desired sound quality.
The reception quality of the tuned radio station
gradually deteriorates or the stored stations are
not working (no sound, 87.5
MHz is displayed...).The vehicle is too far from the transmitter of
the station or no transmitter is present in the
geographical area. Activate the RDS function and search for the
station again to enable the system to check
whether there is a more power ful transmitter in
the geographical area.
The surroundings (hills, buildings, tunnels,
underground car park, etc.) are blocking
reception, including in RDS tracking mode. This phenomenon is normal and does not
indicate a failure of the audio equipment.
The aerial is missing or has been damaged (for
example when going through a car wash or into
an underground car park). Have the aerial checked by a PEUGEOT dealer.
Bluetooth® audio system

1
1
2
1
2
KENWOOD – KDC-X7000DAB
As a safety measure, the vehicle must
be stationary when the driver carries
out operations that require sustained
attention.Short press: on.
Long press: off.
Rotate: set the audio volume,
navigate in a list.
Press: confirm.
Change the audio source.
Short press: accept an incoming
call, switch between two calls, enter
Bluetooth mode.
Long press: smartphone voice
commands via the system.
Short press: find a ser vice.
Long press: update list of stations
received.
Abandon the current operation.
Go up one level in the menu.
Reject or end a call.Select an analogue band FM1/FM2/
FM 3 / M W/ LW.
Select a digital band DB1/DB2/DB3.
Navigate in a list.
Change the search method
(automatic or manual).
Fit the control panel.
Remove the control panel. Short press: find a radio station,
frequency or service, find the
previous/next track or file, navigate
in a list.
Long press: fast for ward or rewind.
Short press: select a preset radio
station.
Long press: add a radio station to
presets.
For more information, refer to the KENWOOD
user guide provided with the system.
.
KENWOOD - KDC-X7000DAB