2018 Peugeot Boxer ESP

143
With steel wheels:
With alloy wheels :
For more information on Identification
markings, including in particular the tyre
pressure label, refer to the corresponding
section.
F

H
ook the carrier I to the outer part.
F

S
crew in the handle H to secure the carrier
and steel wheel.
F

P
osition the support J on the carrier I .
F

T
ighten the handle H .
F

T
ighten the three fixing bolts K of the carrier
I onto the alloy wheel. F

I
nstall the long socket A, the wheelbrace D
and the bar B on the retaining bolt.
F

T
urn the assembly clockwise to fully draw
in the cable and raise the wheel under the
vehicle.
F

C
heck that the wheel is positioned
horizontally flat against the floor of the
vehicle and that the cut-out for the carrier
system is visible.
F

S
tow the tools and the trim (depending on
model).Changing a bulb
The headlamps have polycarbonate
lenses with a
protective coating:
F

d
o not clean them using a dr y or
abrasive cloth, nor with a
detergent
or solvent product,
F

u
se a sponge and soapy water or a pH
neutral product,
F

w
hen using a high pressure washer
on persistent marks, do not keep the
lance directed towards the lamps or
their edges for too long, so as not to
damage their protective coating and
seals.
Changing a


bulb must only be done with
the ignition off and after the headlamp has
been switched off for several minutes –
Risk of serious burns!
F

D
o not touch the bulb directly with your
fingers, use a
lint-free cloth.
It is essential only to use anti-ultraviolet
(UV) type bulbs, so as not to damage the
headlamp.
Always replace a
failed bulb with a new
bulb with the same type and specification.
8
In the event of a breakdown

147
Ty p e C , 12 V10W – 10W
Side marker lamps
Ty p e A , W5W – 5W
Courtesy lamps
F If your vehicle is fitted with these lamps
(L4 body), remove the two fixing screws.
F

P
ull the bulb holder to release it from the
lugs.
F

P
ull the bulb out and change it. Front/Rear
F P ress at the points indicated by the arrows,
then remove the courtesy lamp.
F

O
pen the protective flap.
F

C
hange the bulb by moving the two contacts
apart.
F

E
nsure that the new bulbs are secured
correctly between the two contacts.
F

C
lose the protective flap.
F

F
ix the courtesy lamp in its housing and
ensure that it is secured correctly.
Rear lamps
1. Brake lamps
Ty p e B , P21W – 21W
2. Brake/sidelamps
Ty p e B , P21/5W – 21W and 5W
3. Direction indicators
Ty p e B , PY21W – 21W
4. Reversing lamps
Ty p e A , W16W – 16W
5. Foglamp
Ty p e A , W16W – 16W
For more information on Types of bulbs ,
refer to the corresponding section.
8
In the event of a breakdown

148
Licence plate lamps
Ty p e C, C5W – 5W
F
P
ress the point indicated by the arrow, then
remove the plastic lens.
F

R
emove the failed bulb by moving aside the
two contacts.
F

W
ith the new bulb in place, ensure that it is
secured correctly between the two contacts.
F

R
eplace the plastic lens and press on it to
lock it in place.
F

I

dentify the failed bulb then open the rear
doors.
F

C

arry out these operations in reverse
order to put each bulb in place.
F

R

emove the corresponding access cover by
removing the seven fixing screws (van).
or
R

emove the corresponding access cover by
pulling its handle to unclip it (combi).
F

D

isconnect the electrical connector by
pressing on its central tongue.
F

R

emove the two fixing nuts of the lens unit.
F

P

ull the lens unit from the outside. F

R

emove the six bulb holder fixing screws.
F

S

pread the three retaining tongues and
remove the bulb holder from its housing.
F

C

hange the bulb.
In the event of a breakdown

149
Third brake lamp
Ty p e A, W5W – 5W (x 4)
F
R
emove the two lamp fixing screws.
F

R
emove the lamp by pulling it towards you.
F

R
emove the bulb holder by squeezing the
two tongues inwards.
F

R
emove the failed bulb by pulling it out.
F

C
hange the bulb.
Changing a fuse
The three fuseboxes are located on the
dashboard on the left-hand side, in the pillar
on the right-hand side and in the engine
compartment.
The designations provided are only for the
fuses that can be replaced by the user. For
any other work, visit a
PEUGEOT dealer or
a


qualified workshop. Professional repairers: for full information
on the fuses and relays, consult the
wiring information and diagrams via the
PEUGEOT dealer network.
Removing and fitting a fuse
PEUGEOT accepts no responsibility for
the cost incurred in repairing your vehicle
or for rectifying malfunctions resulting
from the installation of accessories not
supplied by and not recommended by
PEUGEOT and not installed in accordance
with its specifications, in particular when
the combined power consumption of all
of the additional equipment connected
exceeds 10


milliamperes.
Good
Failed
Before changing a fuse, the cause of the fault
must be found and rectified. The numbers of
the fuses are indicated on the fusebox.
Always replace a faulty fuse with a fuse of
the same rating.
8
In the event of a breakdown

157
Engine technical data and
towed loads
Engines
The engine characteristics are given in the
vehicle's registration document, as well as in
sales brochures.The maximum power corresponds to the
value type-approved on a
test bed, under
conditions defined in European legislation
(Directive 1999/99/EC).
For more information, contact a
PEUGEOT
dealer or a
qualified workshop.
Weights and towed loads
The maximum weights and towed loads for
your vehicle are given in the registration
document, as well as in sales brochures.
These values are also given on the
manufacturer's plate or label.
For more information, contact a PEUGEOT
dealer or a
qualified workshop. The GTW and towed load values indicated are
valid up to a
maximum altitude of 1,000 metres.
The towed load value must be reduced by 10%
for each additional 1,000 metres of altitude.
The maximum authorised nose weight
corresponds to the weight permitted on the
towbar (which can be dismantled with or
without a tool).
GT W: Gross train weight.
High exterior temperatures may result
in a reduction in the per formance of
the vehicle to protect the engine. If the
exterior temperature is above 37°C, limit
the towed load.
Towing with a towing vehicle which is only
slightly laden may negatively affect its
handling.
Towing a
trailer increases the braking
distance.
When towing, never exceed the speed
of 62
mph (100 km/h) (obser ve the local
legislation in force). If the exterior temperature is high, it is
recommended that the engine be allowed
to idle for 1
to 2 minutes after the vehicle
comes to a stop, to facilitate its cooling.
9
Technical data

168
Glossary of labels
This section groups together all of the texts that
appear on labels present on the vehicle.For the Identification markings , refer to
the corresponding section.
Under the bonnet
A
Original painting
Colour
Code
Paint
B
ONLY FOR JUMP START C
DANGER
AUTOMATIC ENGINE RESTART. TAKE OUT
THE IGNITION KEY WHEN THE BONNET IS
OPENED.
D
1 - CAUTION
ORIGINAL LUBRICANTS AND FLUIDS
Engine oil Transmission
Radiator Braking
Windscreen washer Power steering
REFER TO MAINTENANCE LOGBOOK. WEAR EYE PROTECTION
Technical data

172
Seat belts
Fastening
F Pull the strap in front of you, with an even movement, ensuring that it does not twist.
F

S
ecure the tongue in its buckle.
F

C
heck that the seat belt is fastened
securely and that the automatic locking
system is operating correctly by pulling the
strap rapidly.
Unfastening
F Press the red button on the buckle, the seat belt rolls up automatically but you are
advised to guide it.
Use the seat belt to restrain only one
person per seat.
Child seats
Do not install child seats, booster
cushions or carry-cots on the rear seats
of the cab.
Each rear seat is fitted with a

three-point inertia
reel seat belt.
Chassis cab/Floor cab
Chassis cab and floor cab
models have a cab, a fixed
floor and two specific rear lamp
clusters.
For more information on these models,
refer to the corresponding section.
Changing a bulb
For more information on Types of bulbs ,
refer to the corresponding section.
These models are also available with:
-

a d
ouble cab,
-

a t
ipper body.
Special features

180
Tipper
Safety recommendations
The tipper body is raised by an electro-
hydraulic unit powered by the vehicle's battery.The tipper body is raised and lowered by
pressing and holding the corresponding
buttons on the magnetic and portable remote
control situated on a
support in the cab.
The tipper body is raised by the motor in the
electro-hydraulic unit.
The tipper body is lowered by a solenoid valve
that opens the fluid return of the ram.
A safety device prevents the tipper body from
dropping when it is not moving or is being
raised. •
N
ever drive with a drop panel lowered.
•
E
nsure that there is no person or
obstacle nearby (below or above)
when unloading.
•
N
ever leave the tipper body raised
when not in use.
•
A
lways discharge the load with the
upper part of the rear drop panel
secured.
•
O
bser ve the maximum payload on the
weight plate on the vehicle.
•
C
heck regularly that the suspension
is in good condition and that the tyres
are inflated to the recommended
pressures.
•

D
istribute the load uniformly in the
tipper body.
•
T

ransport similar products that
discharge easily.
•

N
ever drive, even slowly, with the
tipper body raised.
Tip onto a
sur face that is flat
and hard: a sur face that is
sloping or loose could cause
the centre of gravity to shift,
making the whole vehicle
unstable.
Special features