2018 Peugeot 301 turn signal

13
Under-inflationFixed, accompanied
by an audible signal
and a message. One or more wheels has insufficient
pressure.
Check the pressure of the tyres as soon as possible.
This check should preferably be carried out when the
tyres are cold.
You must reinitialise the system after adjusting one or
more tyre pressures and after changing one or more
wheels.
For more information on Under-inflation detection
,
refer to the corresponding section.
Flashing then fixed,
accompanied by
the Ser vice warning
lamp. The system is faulty: tyre pressures
are no longer monitored.
Check the tyre pressures as soon as possible.
Have the system checked by a PEUGEOT dealer or a
qualified workshop.
Anti-lock
Braking System
(ABS) Fixed.
The anti-lock braking system has a
fault. The vehicle retains conventional braking.
Drive carefully at reduced speed and contact a
PEUGEOT dealer or a qualified workshop without
d e l ay.
Airbags Temporarily on. This warning lamp comes on for a
few seconds when you turn on the
ignition, then goes off.
This warning lamp should go off when the engine is started.
If it does not go off, contact a PEUGEOT dealer or a
qualified workshop.
Fixed.One of the airbag or seat belt
pyrotechnic pretensioner systems
has a fault. Have it checked by a PEUGEOT dealer or a qualified
workshop.
Warning/indicator lamp
StateCause Action/Observations
1
Instruments

16
Warning/indicator lampStateCause Action/Observations
SCR emissions
control system
(BlueHDi Diesel) Fixed, on switching
on the ignition,
associated with the
Service and engine
diagnostic warning
lamps, accompanied
by an audible signal
and a message. A fault with the SCR emissions
control system has been detected.
This alert disappears once the exhaust emissions
return to normal levels.
Flashing, on switching
on the ignition,
associated with the
Service and engine
diagnostic warning
lamps, accompanied by
an audible signal and
a message indicating
the remaining driving
range.After confirmation of the fault with
the emissions control system,
you can continue driving for up to
650
miles (1,100 km) before the
engine starting inhibition system is
triggered. Contact a PEUGEOT dealer or a qualified workshop
without delay
, to avoid a breakdown .
Flashing, on switching
on the ignition,
associated with the
Service and engine
diagnostic warning
lamps, accompanied
by an audible signal
and a message. You have exceeded the authorised
driving limit following confirmation
of a fault with the emissions control
system: the engine starting inhibition
system prevents starting of the
engine.
To be able to restart the engine, you must
call on a
PEUGEOT dealer or a qualified workshop.
Instruments

18
Warning/indicator lampStateCause Action/Observations
Front foglamps Fixed. The front foglamps have been
switched on using the ring on the
lighting control stalk. Turn the ring on the lighting control stalk rear wards
once to switch off the front foglamps.
Left-hand
direction
indicator Flashing with audible
signal.
The lighting control stalk has been
moved down.
Right-hand
direction indicatorFlashing with audible
signal.The lighting control stalk has been
moved up.
Dipped beam
headlamps Fixed.
The lighting control stalk is in the
"Dipped beam headlamps" position.
Main beam
headlamps Fixed.
The lighting control stalk has been
pulled towards you. Pull the stalk to return to dipped beam headlamps.
Foot on the
clutch Fixed.
In STOP mode of Stop & Start, the
transition to START mode has been
rejected because the clutch pedal is
not fully pressed down. With a manual gearbox, you must depress the clutch
pedal fully to allow the change to engine START
mode.
Foot on the
brake Fixed.
With an automatic gearbox, you have
forgotten to press the brake pedal to
move out of position P.With the engine running, before releasing the parking
brake you must press the brake pedal to unlock the
automatic gear selector lever and move out of the
position P
.
Instruments

30
Locking is confirmed by continuous lighting of
the direction indicators for approximately two
seconds.If one of the doors or the boot is still open,
the central locking does not work; the
vehicle locks, then immediately unlocks,
identifiable by the locks making a rebound
sound.
When the vehicle is locked, if it is
unlocked inadvertently, it will lock again
automatically after thirty seconds unless a
door or the boot is open.
Locating your vehicle
This function allows you to identify your vehicle
from a distance, particularly in poor light. Your
vehicle must be locked. F

P
ress the closed padlock button
on the remote control.
This will switch on the courtesy lamps and the
direction indicators will flash for a few seconds.
Fault with the remote
control
In the event of a malfunction of the remote
control, you can no longer unlock, lock or
locate your vehicle.
F

F
irst of all, use the key in the door lock to
unlock or lock your vehicle.
F

T
hen reinitialise the remote control.
Reinitialisation
F Switch off the ignition and remove the key from the switch.
F

P
ress the closed padlock button for a few
seconds.
F

R
eturn the key to position 2 ( ignition on).
F

S
witch off the ignition and remove the key
from the switch.
The remote control is now fully operational
again.
Changing the battery
Battery type: CR2032/3 volts.
If the battery is flat, you are informed
by lighting of this warning lamp in the
instrument panel, an audible signal
and a message in the screen. F

U
nclip the cover by inserting a small
screwdriver in the slot.
F
R
emove the cover.
F
R
emove the flat battery from its
compartment.
F
F
it the new battery into its compartment
observing the original fitting direction.
F
C
lip the cover onto the casing.
Access

33
Doors
Opening
From outside
From inside
Closing
When a door is not closed correctly:-
w
hen the engine is running ,
this warning lamp comes on,
accompanied by a message in
the multifunction screen for a few
seconds,
-

w
hen the vehicle is moving
(speed higher than 6
mph
(10
km/h)), this warning lamp
comes on, accompanied by an
audible signal and a message in
the multifunction screen for a few
seconds.
Emergency release
For mechanically locking and unlocking the
doors in the event of a fault with the central
locking system or a battery failure.
Driver's door
Insert the key in the door lock to lock or unlock
the door.
Passenger doors
F On the rear doors, check that the child lock is not on.
F

A

fter unlocking the vehicle using the remote
control or the key, pull the door handle.
F

P

ull the interior opening control of a door;
this unlocks the whole vehicle. F

R
emove the black cap on the edge of the
door, using the key.
F

I
nsert the key in the socket without forcing
it, then without turning it, move the latch
sideways towards the inside of the door.
F

R
emove the key and refit the cap.
In the event of a fault with the central
locking system, it is essential to
disconnect the battery to lock the boot and
so ensure complete locking of the vehicle.
2
Access

52
Front foglamps and rear foglamp
Turn and release the ring:
F O nce for wards to switch the front foglamps
on.
F

A s
econd time for wards to switch the rear
foglamp on.
F

O
nce rearwards to switch the rear foglamp
of f.
F

A s
econd time rear wards to switch the front
foglamps off.
The foglamps and sidelamps remain on if the
dipped beams are switched off manually.
F

T
urn the ring rear wards to switch the
foglamps off; the sidelamps will then switch
of f. In good or rainy weather, by both day
and night, using the front foglamps and
the rear foglamp is prohibited. In these
situations, the power of their beams may
dazzle other drivers. They should only be
used in fog or falling snow.
In these weather conditions, it is your
responsibility to switch on the foglamps
and dipped headlamps manually as the
sunshine sensor may detect sufficient
light.
Do not forget to turn off the front foglamps
and the rear foglamp as soon as they are
no longer necessary.
Switching off the lighting when the
ignition is switched off
On switching off the ignition, all of the
lamps turn off immediately, except for
dipped beam if automatic guide-me-home
lighting is activated.
Switching on the lighting after
switching off the ignition
To reactivate the lighting control stalk,
rotate the ring to the "0" position – lighting
off, then to the desired position.
When the driver's door is opened, a
temporary audible signal warns you that
the vehicle's lighting is on.
The lighting, with the exception of the
sidelamps, switches off automatically after
a maximum duration of thirty minutes to
prevent discharging of the battery.
Daytime running lamps
(Depending on the country of sale.)
When starting the vehicle, the daytime running
lamps come on automatically, if the lighting
control is in the "0" position.
The daytime running lamps go off
when the sidelamps, dipped beam
or main beam headlamps are
switched on.
This function cannot be deactivated.
Lighting and visibility

61
Anti-lock braking system
(ABS) and electronic brake
force distribution (EBFD)
The fixed illumination of this warning
lamp signals that there is a fault with
the ABS.
Illumination of this warning lamp,
coupled with the STOP and ABS
warning lamps, accompanied by
the display of a message and an
audible signal, signals that there is a
fault with the electronic brake force
distribution (EBFD).
Normal operation of the ABS may make
itself felt by slight vibration of the brake
pedal.
When braking in an emergency, press
firmly without ever releasing the
pressure. When changing wheels (tyres and rims),
ensure that these are approved for your
vehicle.Anti-slip regulation (ASR)/
Dynamic stability control
(DSC)
Operation
These systems are activated automatically
every time the vehicle is started.
They come into operation in the event of a
problem of grip or trajectory.
Deactivation
In exceptional conditions (starting a vehicle
which is bogged down, stuck in snow, on soft
ground, etc.), it may be advisable to deactivate
these systems, so that the wheels can turn
freely and regain grip.
Reactivate the systems as soon as the level of
grip permits.
The vehicle retains conventional braking. Drive
carefully at moderate speed.
Contact a PEUGEOT dealer or a qualified
workshop as soon as possible.
You must stop as soon as it is safe to do so.
Call a PEUGEOT dealer or a qualified
workshop. This is indicated by this warning
lamp flashing in the instrument
panel.F

P
ress this button until the
corresponding symbol appears
in the instrument panel.
The button indicator lamp comes on.
The ASR and DSC systems will no longer have
an effect on engine operation or the brakes in
the event of an involuntary change of trajectory.
Reactivation
The ASR system is reactivated automatically
every time the ignition is switched back on or
from 30
mph (50 km/h).
Below 30
mph (50 km/h), you can reactivate it
manually.
F

P
ress this button again to
reactivate the system manually.
The button indicator lamp goes off.
5
Safety

81
Starting/switching off the
engine
Anti-theft protection
Electronic immobiliser
The key contains an electronic chip which has
a secret code. When the ignition is switched
on, this code must be recognised to enable
engine start.
This electronic engine immobiliser locks the
engine management system a moment after
the ignition is switched off, and prevents
unauthorised engine starting.In the event of a fault, you are
informed by illumination of this
warning lamp, an audible signal and
a message in the screen.
In this case, your vehicle will not start; contact
a PEUGEOT dealer as soon as possible.
Key ignition switch
Ignition on position
It allows the use of the vehicle's electric
equipment or portable devices to be charged.
Once the state of charge of the battery drops
to the reser ve level, the system switches to
energy economy mode: the power supply is
cut off automatically to preser ve the remaining
battery charge. Avoid attaching heavy objects to the key
or the remote control, which would weigh
down on its blade in the ignition switch
and could cause a malfunction.
Starting the engine
The parking brake must be applied.
F

W

ith a manual gearbox, place the gear lever
in neutral then depress the clutch pedal
fully.
F

W

ith an automatic gearbox, select position
P, then firmly press the brake pedal.
F

I

nsert the key into the ignition switch; the
system recognises the code.
F

U

nlock the steering column by
simultaneously turning the steering wheel
and the key.
In certain cases, you may have to turn the
steering wheel with some force to move
the wheels (for example if the wheels are
turned against a kerb).
It has 3 positions:
-

position 1 (Stop): to insert and remove the
key, steering column locked,
-

position 2 (Ignition on) : steering column
unlocked, ignition on, Diesel preheating,
engine running,
-

position 3 (Starting) .
6
Driving