2018 Peugeot 301 light

51
Lighting control stalk
In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps is
normal; it disappears after the lamps have
been on for a few minutes.
Travelling abroad
The design of the dipped beam headlamps
allows, without modification, driving in a
country that drives on the other side of
the road than the country in which your
vehicle was sold.
Selection ring for main
lighting mode
Lighting off (ignition off)/Daytime
running lamps (engine running).
Sidelamps only.
Dipped or main beam headlamps.
Dipping the headlamps
Pull the stalk to switch the lighting
between dipped and main beam
headlamps.
When the lighting is off or only the sidelamps
are on, the driver can switch on the main beam
headlamps by pulling the stalk.
Display
Turn to align the desired symbol with the mark. Illumination of the corresponding indicator
lamp in the instrument panel confirms that the
lighting selected is on.
Foglamp selection ring
The foglamps operate with the dipped and main
beam headlamps.
Rear foglamp only
F To switch it on, turn the ring for wards.
F
T o switch it off, turn the ring rear wards.
4
Lighting and visibility

52
Front foglamps and rear foglamp
Turn and release the ring:
F O nce for wards to switch the front foglamps
on.
F

A s
econd time for wards to switch the rear
foglamp on.
F

O
nce rearwards to switch the rear foglamp
of f.
F

A s
econd time rear wards to switch the front
foglamps off.
The foglamps and sidelamps remain on if the
dipped beams are switched off manually.
F

T
urn the ring rear wards to switch the
foglamps off; the sidelamps will then switch
of f. In good or rainy weather, by both day
and night, using the front foglamps and
the rear foglamp is prohibited. In these
situations, the power of their beams may
dazzle other drivers. They should only be
used in fog or falling snow.
In these weather conditions, it is your
responsibility to switch on the foglamps
and dipped headlamps manually as the
sunshine sensor may detect sufficient
light.
Do not forget to turn off the front foglamps
and the rear foglamp as soon as they are
no longer necessary.
Switching off the lighting when the
ignition is switched off
On switching off the ignition, all of the
lamps turn off immediately, except for
dipped beam if automatic guide-me-home
lighting is activated.
Switching on the lighting after
switching off the ignition
To reactivate the lighting control stalk,
rotate the ring to the "0" position – lighting
off, then to the desired position.
When the driver's door is opened, a
temporary audible signal warns you that
the vehicle's lighting is on.
The lighting, with the exception of the
sidelamps, switches off automatically after
a maximum duration of thirty minutes to
prevent discharging of the battery.
Daytime running lamps
(Depending on the country of sale.)
When starting the vehicle, the daytime running
lamps come on automatically, if the lighting
control is in the "0" position.
The daytime running lamps go off
when the sidelamps, dipped beam
or main beam headlamps are
switched on.
This function cannot be deactivated.
Lighting and visibility

53
Manual guide-me-home
lighting
The temporary illumination of the dipped beam
headlamps after the vehicle's ignition has been
switched off makes the driver's exit easier
when the light is poor.
Switching on
F With the ignition off, "flash" the headlamps using the lighting control stalk.
F

A f
urther "headlamp flash" switches the
function off.
Switching off
Manual guide-me-home lighting goes off
automatically at the end of a given period of
time.
Automatic guide-me-home
lighting
When the automatic headlamp illumination
function is activated (lighting control stalk in the
" AUTO " position), under low ambient light the
dipped beam headlamps remain on when the
ignition is switched off.
With audio system
The guide-me-home lighting can be
configured in the " Personalisation-
configuration " menu.
With touch screen
The guide-me-home lighting can be
configured in the " Driving/Vehicle "
menu.
Direction indicators
Three flashes
F Press briefly upwards or downwards, without going beyond the point of
resistance; the direction indicators will flash
3 times.
F

L
eft: lower the lighting control stalk passing
the point of resistance.
F
R
ight: raise the lighting control stalk passing
the point of resistance.
4
Lighting and visibility

54
Headlamp adjustment
To avoid causing a nuisance to other road
users, the height of the headlamp beams
should be adjusted according to the load in the
vehicle.
Depending on the version, this adjustment can
be carried out using the control located:
-
U
nder the bonnet.
-

T
o the left of the steering wheel
Under the bonnet
To the left of the steering wheel
01 or 2 people in the front seats.
- 5 people.
1 5 people + maximum authorised load in
the boot.
- Driver on their own + maximum authorised
load in the boot.
The higher number positions can be used,
but may limit the area illuminated by the
headlamps.
The initial setting is position " 0".
Wiper control stalk
Front wipers
Fast wiping (heavy rain).
Normal wiping (moderate rain).
Intermittent wiping (proportional to
the speed of the vehicle).
Of f.
Single wipe (press down and
release).
F

R

aise the bonnet to access the control (one
per headlamp).
F

T

urn the control to adjust the height of the
headlamp beam. Raise or lower the control to the desired
position to change the wiping speed.
Lighting and visibility

55
Front windscreen wash
Pull the wiper control stalk towards you. The
windscreen washer and then the wiper operate
for a fixed time.The screenwash jets are not adjustable.
Do not try to move them (risk of damage).
Special position of the
windscreen wipers
This maintenance position is used for cleaning
or replacement of the wiper blades. It can also
be useful, in winter, to release the wiper blades
from the windscreen.
F

O
perate the wiper stalk within one minute
after switching off the ignition to position the
wiper blades vertically on the windscreen. F

T
o park the wiper blades again, switch on
the ignition and operate the wiper stalk.
To maintain the effectiveness of the wiper
blades, it is advisable to:
-
h
andle them with care,
-
c
lean them regularly using soapy
water,
-
a
void using them to retain cardboard
on the windscreen,
-
r
eplace them at the first signs of wear.
Courtesy lamps
A
Courtesy lamps
B Map reading lamps
4
Lighting and visibility

56
Front and rear courtesy lamps
In this position, the courtesy lamp
comes on gradually:
In permanent lighting mode, the lighting time
varies according to the circumstances:
- When the ignition is off, approximately ten minutes.
-

I
n energy saving mode, approximately
thirty seconds.
-

W
hen the engine is running, no limit.
Front map reading lamps
F With the ignition on, press the corresponding switch.
-
W

hen unlocking the vehicle.
-

W

hen the key is removed from the ignition
switch.
-
W

hen opening a door.
-

W

hen activating the locking button on
the remote control in order to locate your
vehicle.
It switches off gradually:
-
W

hen locking the vehicle.
-

W

hen the ignition is switched on.
-

3

0

seconds after the last door is closed. Permanently off.
Permanent lighting.
Lighting and visibility

61
Anti-lock braking system
(ABS) and electronic brake
force distribution (EBFD)
The fixed illumination of this warning
lamp signals that there is a fault with
the ABS.
Illumination of this warning lamp,
coupled with the STOP and ABS
warning lamps, accompanied by
the display of a message and an
audible signal, signals that there is a
fault with the electronic brake force
distribution (EBFD).
Normal operation of the ABS may make
itself felt by slight vibration of the brake
pedal.
When braking in an emergency, press
firmly without ever releasing the
pressure. When changing wheels (tyres and rims),
ensure that these are approved for your
vehicle.Anti-slip regulation (ASR)/
Dynamic stability control
(DSC)
Operation
These systems are activated automatically
every time the vehicle is started.
They come into operation in the event of a
problem of grip or trajectory.
Deactivation
In exceptional conditions (starting a vehicle
which is bogged down, stuck in snow, on soft
ground, etc.), it may be advisable to deactivate
these systems, so that the wheels can turn
freely and regain grip.
Reactivate the systems as soon as the level of
grip permits.
The vehicle retains conventional braking. Drive
carefully at moderate speed.
Contact a PEUGEOT dealer or a qualified
workshop as soon as possible.
You must stop as soon as it is safe to do so.
Call a PEUGEOT dealer or a qualified
workshop. This is indicated by this warning
lamp flashing in the instrument
panel.F

P
ress this button until the
corresponding symbol appears
in the instrument panel.
The button indicator lamp comes on.
The ASR and DSC systems will no longer have
an effect on engine operation or the brakes in
the event of an involuntary change of trajectory.
Reactivation
The ASR system is reactivated automatically
every time the ignition is switched back on or
from 30
mph (50 km/h).
Below 30
mph (50 km/h), you can reactivate it
manually.
F

P
ress this button again to
reactivate the system manually.
The button indicator lamp goes off.
5
Safety

64
Advice
The driver must ensure that passengers use
the seat belts correctly and that they are all
restrained securely before setting off.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for short
journeys.
Do not interchange the seat belt buckles as
they will not completely fulfil their role.
The safety belts are equipped with an
inertia reel which allows the strap length to
automatically adjust to your shape. The seat
belt returns to its storage automatically when
it is not used.
Before and after use, ensure that the seat belt
is reeled in correctly.
The lower part of the strap must be positioned
as low as possible on the pelvis.
The upper part must be positioned in the
hollow of the shoulder.
The inertia reels are fitted with a device which
automatically locks the strap in the event
of a collision or emergency braking or if the
vehicle rolls over. You can release the device
by pulling the strap firmly and then releasing it
so that it reels in slightly.In order to be effective, a seat belt:
-
M ust be tightened as close to the body as
possible,
-

M
ust be pulled in front of you with a
smooth movement, ensuring that it is not
twisted,
-

M
ust only be used to secure one person,
-

M
ust not show signs of tear or fraying.
-

M
ust not be changed or modified, in order
to avoid affecting its performance. Instructions for children
Use a suitable child seat, if the passenger is
less than 12
years old or shorter than one and
a half metres.
Never use the same seat belt to secure more
than one person.
Never allow a child to travel on your lap.
For more information on Child seats , refer to
the corresponding section.
In accordance with current safety regulations,
for all repairs on your vehicle's seat belts, go
to a qualified workshop with the skills and
equipment needed, which a PEUGEOT dealer
is able to provide.
Have your seat belts checked regularly by a
PEUGEOT dealer or a qualified workshop,
particularly if the straps show signs of
damage.
Clean the seat belt straps with soapy water or
a textile cleaning product, sold by PEUGEOT
dealers.
After folding or moving a seat or a rear bench
seat, ensure that the seat belt is positioned
and reeled in correctly. In the event of an impact
Depending on the nature and seriousness
of the impacts
, the pyrotechnic pretensioner
device may trigger before and independently
of airbag deployment. Deployment of the
pretensioners is accompanied by a slight
discharge of harmless smoke and a noise,
due to the activation of the pyrotechnic
cartridge incorporated in the system.
In all cases, the airbag warning lamp comes
on.
After an impact, get the seat belt system
checked and, if necessary, have it replaced
by a PEUGEOT dealer or a qualified
workshop.
Safety