2018 Peugeot 208 reset

88
With PureTech petrol and manual or
automatic gearbox:
-

A
s soon as the vehicle stops or the speed
is less than 2
mph (3 km/h) (with manual
gearbox and depending on version).
-

W
ith gear lever in neutral and clutch pedal
released (manual gearbox).
-

W
ith brake pedal pressed or gear lever in
position N (automatic gearbox).
Special cases: STOP mode not
available
STOP mode is not triggered when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he vehicle has not exceeded 6 mph
(10
km/h) since the last engine start using
t h e key,
-

t
he engine is needed to maintain
a


comfortable temperature in the passenger
compartment,
-

d
emisting is active,
-

s
ome temporary conditions (battery charge,
engine temperature, braking assistance,
exterior temperature, etc.) make this
necessary to ensure control of a
system.
This indicator lamp flashes for a
few
seconds, then goes off.
This operation is perfectly normal. A time counter calculates the
time spent in STOP mode during
a
journey. It is reset to zero every
time the ignition is switched on
using the key.
For your comfort, during parking
manoeuvres, STOP mode is not available
for a few seconds after coming out of
reverse gear.
The Stop & Start system does not affect
the functionalities of the vehicle, such as
braking.
With a
manual gearbox in STOP mode, if
a
gear is engaged without fully depressing
the clutch pedal, a message is displayed
asking you to depress the clutch pedal
again to restart the engine.
START mode
This indicator lamp goes off and the
engine restarts. With manual gearbox
:
-
W
ith clutch pedal depressed.
With automatic gearbox:
-
W
ith gear lever in position D or M
.
-
W
ith brake pedal released.
or
-
W
ith gear lever in position N.
-
W
ith brake pedal released.
-
T
hen gear lever in position D or M
.
or
-
W
ith reverse gear engaged.
Special cases: START mode
triggered automatically
As a safety measure and for your convenience,
S TART mode is triggered automatically when:
-
y

ou open the driver's door,
-
y

ou unfasten the driver's seat belt,
-

s
ome temporary conditions (battery charge,
engine temperature, braking assistance,
air conditioning setting, etc.) make this
necessary to ensure control of a
system or
the vehicle.
This indicator lamp flashes for a
few
seconds, then goes off.
This operation is perfectly normal.
Never refuel with the engine in STOP
mode; you must switch off the ignition
using the key.
Driving

140
Quick-release terminal clamp
Disconnecting the (+) terminalReconnecting the (+) terminal
Do not force the lever as locking will not
be possible if the clamp is not positioned
correctly; start the procedure again.
Before disconnecting
Wait 2 minutes after switching off the ignition
b efore disconnecting the battery.
Close the windows and the doors before
disconnecting the battery.
Following reconnection
After each time that the battery has been
reconnected, switch on the ignition and wait
1
minute before starting the engine, to allow
the electronic systems to initialise. However,
if minor problems persist after this procedure,
contact a
PEUGEOT dealer or a qualified
workshop.
Referring to the corresponding section, you
must yourself reinitialise:
-

t
he remote control key,
-

t
he date and time,
-

t
he radio preset stations.
F

Ra

ise the lever A fully to release the
clamp B .
F

R

emove the clamp B by lifting it off. F

Ra

ise the lever A fully.
F

R

efit the open clamp B on the (+) terminal.
F

P

ush the clamp B fully down.
F

L

ower the lever A to lock the clamp B .
To w i n g
Procedure for having your vehicle towed or for
towing another vehicle using the towing eye.
F

s

witch off all electrical consumers (audio
system, wipers, lighting, etc.),
F

s

witch off the ignition and wait for 4

m

inutes.
At the battery, it is only necessary to
disconnect the (+) terminal.
In the event of a breakdown

1
Audio system
Contents
First steps
1
S

teering mounted controls
2
R

adio
2
M

edia
3
A

udio settings
5
F

requently asked questions
5
F

or safety reasons, the vehicle must
always be stationary for the driver to
perform operations that require close
attention.
When the engine is switched off and to
prevent discharging of the battery, the
system switches off after activation of
energy economy mode.First steps
On/Off, volume adjustment.
Select the source:
FM1, FM2, AM, CD, AUX.
Adjust audio settings:
sound ambience, treble, bass,
loudness, left/right balance,
automatic volume.
Automatic search for a
lower radio
frequency.
Select the previous CD track.
Scroll in a
list.
Press and hold: rewind. Display the list of stations received,
the CD/MP3
tracks or folders.
Press and hold: update the list of
stations received.
Manual search step by step for
a

higher radio frequency.
Select the next MP3 folder.
Scroll in a list.
Manual search step by step for
a lower radio frequency.
Select the previous MP3 folder.
Scroll in a list.
Cancel the current operation.
Go up one level (menu or folder).
Automatic search for a
higher radio
frequency.
Select the next CD track.
Scroll in a
list.
Press and hold: fast for ward.
Access to the main menu.
Select a


preset radio station.
Radio, press and hold: store
a


station.
Eject CD.
.
Audio system

2
Steering mounted controls
Radio: select the previous/next
preset radio station.
Select the previous/next item in
a menu.
Radio: automatic search for a
higher
frequency.
CD/MP3: select the next track.
CD: press and hold: fast for ward.
Change the audio source.
Confirm a


selection.
Radio: automatic search for a
lower
frequency.
CD/MP3: select the previous track.
CD: press and hold: rewind.
Increase volume.
Decrease volume.
Mute on: cut the sound by
simultaneously pressing the volume
up and down buttons.
Mute off: press one of the two
volume buttons.
Radio
Presetting a station
Press the SRC/BAND button
repeatedly to select the FM1, FM2 or
AM waveband.
Press and hold a
button to preset
the station being listened to. The
name of the station is displayed and
an audible signal confirms that it has
been preset.
The external environment (hills, buildings,
tunnels, basement car parks, etc.) may
block reception, including in RDS tracking
mode. This is a
normal effect of the way
in which radio waves are transmitted and
does not indicate any failure of the audio
equipment.
Selecting a station
Press a button to listen to the
c orresponding preset station.
Managing the list
Press LIST to display the list of
stations received in alphabetical
o r d e r. Select the desired radio station by
pressing one of the buttons.
Confirm with OK.
Briefly press one of the buttons to
change to the next or previous letter.
Press and hold LIST
to build or
update the list of stations; audio
reception is cut momentarily.
Press MENU .
Select " Radio".
Confirm with OK.
Select " RDS".
RDS
RDS, if displayed, allows you to continue
listening to the same station by automatically
retuning to alternative frequencies. However,
in certain conditions, coverage of an RDS
station may not be assured throughout the
entire country as radio stations do not cover
100% of the territory. This explains the loss
of reception of a
station during a journey.
Audio system

6
QUESTIONRESPONSESOLUTION
There is a difference in sound quality between
the different audio sources (radio, CD, etc.). To allow for optimal listening quality, the audio
settings (Volume, Bass, Treble, Ambience,
Loudness) can be tailored to different
sound sources, which can generate audible
differences when changing source (radio, CD,
e t c .) .Check that the audio settings (Volume, Bass,
Treble, Ambience, Loudness) are adapted to
the sources listened to. It is advisable to set
the AUDIO functions (Bass, Treble, Front-
Rear Fader, Left-Right Balance) to the middle
position, select the musical ambience "None"
and set the loudness correction to the "Active"
position in CD mode or to the "Inactive" position
in radio mode.
When changing the settings for treble and bass,
the ambiance setting is deselected.
When changing the ambience setting, treble
and bass are reset to zero. Choosing an ambience imposes settings for
treble and bass. Modifying one without the other
is not possible.
Modify the treble and bass settings or the
ambience setting to obtain the desired sound
quality.
The reception quality of the tuned radio station
gradually deteriorates or the stored stations are not
working (no sound, 87.5
MHz is displayed, etc.).The vehicle is too far from the transmitter of
the station or no transmitter is present in the
geographical area. Activate the RDS mode and start a
new search
for the station so that the system can check
whether a
stronger transmitter is available in the
geographic area.
The environment (hills, buildings, tunnels,
basement car parks, etc.) blocks reception,
including in RDS tracking mode. This phenomenon is normal and does not
indicate a
failure of the audio equipment.
The aerial is missing or has been damaged (for
example when going through a
car wash or into
an underground car park). Have the aerial checked by a
PEUGEOT dealer.
Audio system

1
Audio system/Bluetooth®
Contents
First steps
1
S

teering mounted controls
2
R

adio
2
M

edia
3
T

elephone
6
A

udio settings
8
C

onfiguration
9
F

requently asked questions
9
F

or safety reasons, the vehicle must
always be stationary for the driver to
perform operations that require close
attention.
When the engine is switched off and to
prevent discharging of the battery, the
system switches off after activation of
energy economy mode.First steps
On/Off, volume adjustment.
Adjust audio options: sound
ambience, treble, bass, loudness,
distribution, left/right balance, front/
rear balance, automatic volume.
Automatic search for a
lower radio
frequency.
Select the previous CD, USB track.
Scroll in a
list.
Press and hold: rewind. Display the list of stations received,
the CD/USB tracks or folders.
Press and hold: update the list of
stations received.
Cancel the current operation.
Go up one level (menu or folder).
Automatic search for a
higher radio
frequency.
Select the next CD, USB track.
Scroll in a list.
Press and hold: fast for ward.
Access to the main menu.
Select preset radio station.
Radio, press and hold: store
a


station.
Other than radio: see the
corresponding sections.
Eject CD.
Select the source:
Radio: FM1, FM2, AM, CD, USB,
AUX, Streaming.
Telephone: accept an incoming call.
Telephone, press and hold: end
a
call, access the calls log for the
connected telephone.
.
Bluetooth® audio system

2
Steering mounted controls
Radio: select the previous/next
preset radio station.
CD/USB: select the genre/artist /
folder from the classification list.
Select the previous/next item in
a menu.
Radio: automatic search for higher
frequency.
CD/MP3/USB: select the next track.
CD/USB: press and hold: fast
forward.
Change the audio source.
Confirm a


selection.
Call/end call on the telephone.
Press and hold: access to the calls
list.
Radio: automatic search for lower
frequency.
CD/MP3/USB: select the previous
track.
CD/USB: press and hold: rewind.
Increase volume.
Decrease volume. Mute on: cut the sound by
simultaneously pressing the volume
increase and decrease buttons.
Mute off: press one of the two
volume buttons.
Radio
Presetting a station
Press SRC/TEL
repeatedly to select
the FM1, FM2 or AM waveband.
Press and hold a
button to preset
the station being listened to. The
name of the station is displayed and
an audible signal confirms that it has
been preset.
The external environment (hills, buildings,
tunnels, basement car parks, etc.) may
block reception, including in RDS tracking
mode. This is a
normal effect of the way
in which radio waves are transmitted and
does not indicate any failure of the audio
equipment.
Selecting a station
Press a button to listen to the
c orresponding preset station.
Managing a list
Press LIST to display the list of
stations received in alphabetical
o r d e r.
Select the desired radio station
using one of the buttons.
Confirm with " OK".
Briefly press one of the buttons to
change to the next or previous letter.
Press and hold LIST to build or
update the list of stations; audio
reception is cut momentarily.
Entering a frequency
Press MENU .
Select "Radio ".
Select "Write freq. ".
Press + ,
or press – to select the desired
frequency.
Confirm with " OK".
Bluetooth® audio system

10
QUESTIONRESPONSESOLUTION
There is a difference in sound quality between
the different audio sources (radio, CD, etc.). For optimum sound quality, the audio settings
(volume, bass, treble, ambience, loudness)
can be adapted to the different sound sources,
which may result in audible differences when
changing source (radio, CD, etc.).Check that the audio settings (volume, bass,
treble, ambience, loudness) are adapted to
the sources being listened to. It is advisable to
set the AUDIO functions (bass, treble, front-
rear balance, left-right balance) to the middle
position, select the musical ambience and set
the loudness correction to the "Active" position
in CD mode or to the "Inactive" position in radio
mode.
When changing the settings for treble and bass,
the ambience setting is deselected.
When changing the ambience setting, treble
and bass are reset to zero. Choosing an ambience imposes settings for
treble and bass. Modifying one without the other
is only possible with a


personalised ambienceModify the treble and bass settings or the
ambience setting to obtain the desired sound
quality.
When changing the balance setting, distribution
is deselected. Choosing the "driver" distribution setting
imposes a


balance setting.Modify the balance or distribution settings to
obtain the desired sound quality.
The reception quality of the tuned radio station
gradually deteriorates or the stored stations are
not working (no sound, 87.5
MHz is displayed,
e t c .) . The vehicle is too far from the transmitter of
the station or no transmitter is present in the
geographical area.
Activate the RDS function to enable the system
to check whether there is a
more power ful
transmitter in the geographical area.
The surroundings (hills, buildings, tunnels,
underground parking, etc.) are blocking
reception, including in RDS tracking mode. This phenomenon is normal and does not
indicate a
failure of the audio equipment.
The aerial is missing or has been damaged (for
example when going through a
car wash or into
an underground car park). Have the aerial checked by a
PEUGEOT dealer.
Bluetooth® audio system