2018 NISSAN GT-R ECU

ensure the resistance strength and
creeping characteristics against high ex-
haust gas temperature. In addition,
further cooling effects are secured by
taking in air through the duct on the
undercover, to cool the area around the
muffler, and by applying partial plate
thickness reduction. Since genuine tita-
nium mufflers are made of titanium alloy,
the surface color will change depending
on the driving conditions, which is not
unusual. Prior to shipping from factory, all
vehicles receive balance aligning for en-
gine, transmission, and clutch, as well as
quench driving of brake pads and rotors.
As a result, the muffler surface color may
differ depending on the vehicle.
Never remove the trunk carpet from the
vehicle for any reason. The carpet insu-
lates the vehicle interior from the heat of
the muffler and from the noise of the
transmission.
Never Allow Oil or Grease to Adhere to
the Titanium Muffler.
If the muffler is heated when oil or grease
adhere to the muffler surface, the color of
this area will be different from that of the
surrounding area. To remove the oil or
grease, check that the surface tempera-
ture of the muffler has cooled, wash the
area with a neutral detergent, wipe it witha brake cleaner-sprayed clean shop cloth
and gently tap it with a dry shop cloth to
dry. Be careful not to allow the brake
cleaner to splatter on rubber parts, bum-
per, etc.

accident.
. Be sure the seat belt tongue is
securely fastened to the proper
buckle.
. Do not wear the seat belt inside
out or twisted. Doing so may
reduce its effectiveness.
. Do not allow more than one
person to use the same seat belt.
. Never carry more people in the
vehicle than there are seat belts.
. If the seat belt warning light
glows continuously while the
ignition is turned ON with all
doors closed and all seat belts
fastened, it may indicate a mal-
function in the system. It is re-
commended you have the system
checked by a GT-R certified
NISSAN dealer.
. No changes should be made to
the seat belt system. For exam-
ple, do not modify the seat belt,
add material, or install devices
that may change the seat belt
routing or tension. Doing so may
affect the operation of the seat
belt system. Modifying or tam-
pering with the seat belt system
may result in serious personal injury.
. Once a seat belt pretensioner has
activated, it cannot be reused and
must be replaced together with
the retractor. It is recommended
you see a GT-R certified NISSAN
dealer.
. Removal and installation of the
pretensioner system components
should be done by a GT-R certi-
fied NISSAN dealer.
. All seat belt assemblies, including
retractors and attaching hard-
ware, should be inspected after
any collision by a GT-R certified
NISSAN dealer. NISSAN recom-
mends that all seat belt assem-
blies in use during a collision be
replaced unless the collision was
minor and the belts show no
damage and continue to operate
properly. Seat belt assemblies
not in use during a collision
should also be inspected and
replaced if either damage or im-
proper operation is noted.
. All child restraints and attaching
hardware should be inspected
after any collision. Always follow
the restraint manufacturer’s in- spection instructions and repla-
cement recommendations. The
child restraints should be re-
placed if they are damaged.

OPENING AND CLOSING THE
TRUNKWhen opening the trunk, first unlock it
then lift up the trunk lid so that it is fully
open.
When closing the trunk, lower the trunk
lid and press it until it is securely locked in
place. The strap

is used.
. Objects in the RearView Monitor
will appear visually opposite
compared to when viewed in the
rearview and outside mirrors.
. Use the displayed lines as a re-
ference. The lines are highly af-
fected by the number of
occupants, fuel level, vehicle po-
sition, road conditions and road
grade.
. Make sure that the trunk lid is
securely closed when backing up.
. Do not put anything on the rear-
view camera. The rearview cam-
era is installed above the license
plate.
. When washing the vehicle with
high-pressure water, be sure not
to spray it around the camera.
Otherwise, water may enter the
camera unit causing water con-
densation on the lens, a malfunc-
tion, fire or an electric shock.
. Do not strike the camera. It is a
precision instrument. Otherwise,
it may malfunction or cause da-
mage resulting in a fire or an
electric shock. The following are operating limitations
and do not represent a system malfunc-
tion:
.
When the temperature is extremely
high or low, the screen may not clearly
display objects.
. When strong light is directly coming
on the camera, objects may not be
displayed clearly.
. Vertical lines may be seen in objects
on the screen. This is due to strong
reflected light from the bumper.
. The screen may flicker under fluores-
cent light.
. The colors of objects on the RearView
Monitor may differ somewhat from
the actual color of objects.
. Objects on the monitor may not be
clear in a dark environment.
. There may be a delay when switching
to the RearView Monitor screen.
. If dirt, rain or snow accumulates on
the camera, the RearView Monitor
may not display objects clearly. Clean
the camera.
. Do not use wax on the camera win-
dow. Wipe off any wax with a clean
cloth dampened with mild detergent
diluted with water.

OPENING AND CLOSING THE
TRUNKWhen opening the trunk, first unlock it
then lift up the trunk lid so that it is fully
open.
When closing the trunk, lower the trunk
lid and press it until it is securely locked in
place. The strap

is used.
. Objects in the RearView Monitor
will appear visually opposite
compared to when viewed in the
rearview and outside mirrors.
. Use the displayed lines as a re-
ference. The lines are highly af-
fected by the number of
occupants, fuel level, vehicle po-
sition, road conditions and road
grade.
. Make sure that the trunk lid is
securely closed when backing up.
. Do not put anything on the rear-
view camera. The rearview cam-
era is installed above the license
plate.
. When washing the vehicle with
high-pressure water, be sure not
to spray it around the camera.
Otherwise, water may enter the
camera unit causing water con-
densation on the lens, a malfunc-
tion, fire or an electric shock.
. Do not strike the camera. It is a
precision instrument. Otherwise,
it may malfunction or cause da-
mage resulting in a fire or an
electric shock. The following are operating limitations
and do not represent a system malfunc-
tion:
.
When the temperature is extremely
high or low, the screen may not clearly
display objects.
. When strong light is directly coming
on the camera, objects may not be
displayed clearly.
. Vertical lines may be seen in objects
on the screen. This is due to strong
reflected light from the bumper.
. The screen may flicker under fluores-
cent light.
. The colors of objects on the RearView
Monitor may differ somewhat from
the actual color of objects.
. Objects on the monitor may not be
clear in a dark environment.
. There may be a delay when switching
to the RearView Monitor screen.
. If dirt, rain or snow accumulates on
the camera, the RearView Monitor
may not display objects clearly. Clean
the camera.
. Do not use wax on the camera win-
dow. Wipe off any wax with a clean
cloth dampened with mild detergent
diluted with water.

NOTE:.
As soon as possible, tighten the
wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque:
Except for NISMO models 97 ft-lb (132 N·m)
NISMO models 114 ft-lb (155 N·m)
The wheel nuts must be kept
tightened to specification at all
times. It is recommended that
wheel nuts be tightened to speci-
fications at each lubrication inter-
val.
.
Adjust tire pressure to the COLD
pressure.
COLD pressure: After the vehicle
has been parked for three hours
or more or driven less than 1 mile
(1.6 km).
COLD tire pressures are shown on
the Tire and Loading Information
label affixed to the driver’s door
opening.
10. Securely store the jacking equipment in the vehicle.

ensure the resistance strength and
creeping characteristics against high ex-
haust gas temperature. In addition,
further cooling effects are secured by
taking in air through the duct on the
undercover, to cool the area around the
muffler, and by applying partial plate
thickness reduction. Since genuine tita-
nium mufflers are made of titanium alloy,
the surface color will change depending
on the driving conditions, which is not
unusual. Prior to shipping from factory, all
vehicles receive balance aligning for en-
gine, transmission, and clutch, as well as
quench driving of brake pads and rotors.
As a result, the muffler surface color may
differ depending on the vehicle.
Never remove the trunk carpet from the
vehicle for any reason. The carpet insu-
lates the vehicle interior from the heat of
the muffler and from the noise of the
transmission.
Never Allow Oil or Grease to Adhere to
the Titanium Muffler.
If the muffler is heated when oil or grease
adhere to the muffler surface, the color of
this area will be different from that of the
surrounding area. To remove the oil or
grease, check that the surface tempera-
ture of the muffler has cooled, wash the
area with a neutral detergent, wipe it witha brake cleaner-sprayed clean shop cloth
and gently tap it with a dry shop cloth to
dry. Be careful not to allow the brake
cleaner to splatter on rubber parts, bum-
per, etc.