2018 MITSUBISHI OUTLANDER PHEV brake

When charging the drive battery
When there is no energy flow
ECO Score
E00531601207
ECO score indicates the points you havescored on fuel-efficient driving by the num-
ber of leaves as follows:

[When the operation mode is ON]
The display shows the score you achieved in the last several minutes.

[When the operation mode is put in OFF]
The display shows the overall ECO score the
function has counted from the time when the operation mode is set to “ON” to the time when it is set to “OFF”.Changing the function settings
E00522701879
The “Display language”, “Temperature unit”,
“Fuel consumption unit”, and “Average fuel
consumption and speed reset method” etc. setting can be modified as desired. 1. Stop the vehicle in a safe place.
Firmly apply the parking brake, andpress the electrical parking switch andshift to “P” (PARK) position.
2. Lightly press the multi information dis-
play switch a few times to switch the in-
formation screen to the function setting screen.
Refer to “Information screen” on page
6-07.
CAUTIONl For safety, stop the vehicle before operating.
While driving, even if you operate the multi information display switch, the function set- ting screen is not displayed.
3. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from the setting mode screen
to the menu screen.
Multi information display
6-15OGGE18E1Instruments and controls6 ECO drive level
Low High

Indication lamp, warning lamp, and information screen display listE00523701267
Indication and warning lamp list
E00523802539
1- Position lamp indication lamp ® p. 6-48
2- Front fog lamp indication lamp ® p. 6-48
3- Turn-signal indication lamps/Hazard warning indication lamps ® p. 6-47
4- Rear fog lamp indication lamp ® p. 6-48
5- High-beam indication lamp ® p. 6-476- Plug-in Hybrid EV System warning
lamp ® p. 6-50
7- Auxiliary battery charge warning lamp ® p. 6-50
8- Charging indicator ® p. 6-48
9- Regenerative brake warning lamp ® p. 6-51
10- Blind Spot Warning (BSW) indication lamp* ® p. 7-79
11- Ready indicator ® p. 6-4812- Automatic High-Beam (AHB) indication
lamp* ® p. 6-54
13- Acoustic Vehicle Alerting System (AVAS) OFF indication lamp
® p. 7-30
14- LED headlamp warning lamp* ® p. 6-53
15- Active Stability Control (ASC) indica- tion lamp ® p. 7-42
Indication lamp, warning lamp, and information screen display list
6-21OGGE18E1Instruments and controls6

16- Active Stability Control (ASC) OFF in-dication lamp ® p. 7-41
17- Anti-lock brake system (ABS) warning lamp ® p. 7-37
18- Supplement Restraint System (SRS) warning lamp ® p. 5-3619- Check engine warning lamp ® p. 6-49
20- Electric parking brake warning lamp (yellow) ® p. 7-03
21- Seat belt warning lamp ® p. 5-11
22- Tyre pressure monitoring system warn- ing lamp ® p. 7-9023- Brake auto hold indication lamp
® p. 7-32
24- Brake warning lamp (red) ® p. 6-48
25- Information screen display list ® p. 6-22

Information screen display list
E00523901344
When there is information to be announced, such as lamp reminder, the buzzer sounds and the screen switches to the displays shown below.
Refer to the appropriate page and take the necessary measures.
When the cause of the warning display is eliminated, the warning display goes out automatically. Refer to “Warning display list” on page 6-23.
Refer to “Navigation information display” on page 6-40. Refer to “Other interrupt displays” on page 6-41.
NOTEl A warning may be displayed on the information screen and the buzzer may sound in the following rare cases.
This is caused by the system picking up interference such as noise or strong electromagnetic waves, and is not a functional problem.
• An extremely strong electromagnetic wave is received from a source such as an illegal radio set, a spark from a wire, or a radar station.
• Abnormal voltage or a static electricity discharge is generated by the operation of installed electrical equipment (including after-market parts).
If the warning display appears many times, we recommend you to consult a MITSUBISHI MOTORS Authorized Service Point.

Indication lamp, warning lamp, and information screen display list
6-22OGGE18E1Instruments and controls6

Warning display list
E00524002466
ScreenCauseSolution (Reference)lOne or more failure is occurring in the
Plug-in Hybrid EV System.l Have your vehicle inspected by a
MITSUBISHI MOTORS Authorized
Service Point.l One or more failure is occurring in the
Plug-in Hybrid EV System.l Immediately park the vehicle in a safe
place and contact a MITSUBISHI
MOTORS Authorized Service Point.l The parking lock unit is in failure. The
Plug-in Hybrid EV System cannot be keptin standstill condition without applying the parking brake.l Park the vehicle at a safe, flat place and
apply the parking brake. Contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Electrical Parking switch” on page 7-18.l You are attempting to set the operation
mode to “ON” when the charge connector
is connected to the charge port.l Disconnect the charge connector from the
charge port before operating the power switch.l Charging was interrupted due to system
failure or EV charging cable failure.l There is a system failure or the EV charg-
ing charge cable is faulty. Immediately
stop using the cable and contact a
MITSUBISHI MOTORS Authorized
Service Point.
Indication lamp, warning lamp, and information screen display list
6-23OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThe keyless operation key is not detected.lInsert the keyless operation key into the
key slot.
Refer to “If the keyless operation key is not operating properly” on page 7-15.l You have forgotten to remove the keyless
operation key from the key slot.l Remove the keyless operation key from
the key slot.
Refer to “Keyless operation key remind-
er” on page 7-16.l There is a fault in the EPS.l Have the vehicle inspected by a
MITSUBISHI MOTORS Authorized
Service Point as soon as possible.
Refer to “Electric power steering system
(EPS)” on page 7-39.l The RBS (regenerative brake system) can-
not be used.l Have your vehicle inspected by a
MITSUBISHI MOTORS Authorized
Service Point.
Indication lamp, warning lamp, and information screen display list
6-27OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThere is a fault in the fuel system.l We recommend you to have it checked,
immediately.l The fuel is running low.lRefuel as soon as possible. Refer to
“Fuel
remaining warning display” on page 6-10.l You are driving with the parking brake
still applied.l Release the parking brake. Refer to
“Brake warning display” on page 6-51.l The brake fluid level in the reservoir has
fallen to a low level.
l There is a fault in the brake system.lImmediately stop the vehicle in a safe
place.
We recommend you to consult a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Brake warning display” on page 6-51.l When the brake pedal has been repeatedly
depressed over a short period of time, the brake warning lamp may come on and thebrake warning buzzer may sound, and this
warning may be displayed.l If this warning display has disappeared
and the brake warning lamp goes out and the buzzer stops a few seconds after stop-
ping the brake operation, there is no ab-
normality.
Indication lamp, warning lamp, and information screen display list
6-30OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThere is a fault with the Electric parking
brake.l We recommend you to have it checked,
immediately.
Refer to “Electric parking brake” on page
7-03.l The parking brake cannot be applied tem-
porarily due to repeated operation of the
Electric parking brake switch within a short time.l Refer to “Electric parking brake” on page
7-03.l You try to release the Electric parking
brake switch without depressing the brake pedal.l Refer to “Electric parking brake” on page
7-03.l The Electric parking brake has been auto-
matically applied.l Refer to “Brake auto hold” on page 7-32.lThe brake auto hold is automatically can-
celled.l Refer to “Brake auto hold” on page 7-32.
Indication lamp, warning lamp, and information screen display list
6-31OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThe brake auto hold is not available.l Refer to “Brake auto hold” on page 7-32.lThe brake auto hold system does not turn
on because the driver’s seat belt is not fas-
tened.l Press the brake auto hold switch after fas-
tening the driver’s seat belt.
Refer to “Brake auto hold” on page 7-32.l The brake auto hold system does not turn
off because the brake pedal is not pressed.l Depress the brake pedal more firmly than
usual with the right foot. Then, press the
brake auto hold switch.
Refer to “Brake auto hold” on page 7-32.l There is a fault in the engine oil circula-
tion system.l Immediately stop the vehicle in a safe
place. We recommend you to have it checked.
Refer to “Oil pressure warning display” on page 6-51.l There is a fault in the Supplemental re-
straint system (SRS) airbag or the preten-
sioner system.l We recommend you to have it checked,
immediately.
Refer to “SRS warning lamp/display” on
page 5-36.
Indication lamp, warning lamp, and information screen display list
6-32OGGE18E1Instruments and controls6