2018 MITSUBISHI OUTLANDER oil

Engine oil and oil filter
Vehicle care and maintenance 9-7
9
Mitsubishi Motors re
commends using only
engine oils with the ILSAC certification sym-bol on the front of the container.If you cannot find oils
with the ILSAC certi-
fication symbol, use an
API classification SN
oil with the following label.
This mark appears on the top of the oil con-tainer and tells you two important thingsabout the oil.Use engine oil with the proper thickness forthe outdoor temperatures where you will bedriving.
Mitsubishi Motors Genui
ne 0W-20 Synthetic
Engine Oil is recommended for optimum fueleconomy and cold weather starting.If Mitsubishi Motors Genuine 0W-20 Syn-thetic Engine Oil is not available, 5W-20grade oils displaying the ILSAC certificationcan be used.However, Mitsubishi
Motors Genuine 0W-20
Synthetic Engine Oil s
hould be used at the
next oil change to maintain optimum fueleconomy and cold weather starting.The oil filter should be replaced at the time ormileage specified in the “WARRANTY ANDMAINTENANCE MANUAL”.Only use high quality replacement filters onthis vehicle. The manufacturer’s specifica-tions for Mitsubishi Mo
tors Genuine oil fil-
The engine oil wi
ll deteriorate rapidly if the
vehicle is subj
ected to severe conditions (for
example, repeated operation on rough roads,in mountainous regions, on roads with manyuphill and downhill gradients, or over shortdistances). Consequently
, the oil will require
earlier replacement in accordance with theschedule in the “WARRANTY AND MAIN-TENANCE MANUAL”.NOTE
ILSAC certification symbol
1- The upper part indi
cates the quality of
the oil.
2- The center part i
ndicates the SAE grade
of the oil viscosity.
Recommended engine oil vis-cosity API service symbol
To replace the oil filter
BK0249100US.book 7 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Engine coolant9-8 Vehicle care and maintenance
9
ters require that the filter can withstand apressure of 256 psi (1.8 MPa). A MitsubishiMotors Genuine oil filter
is the best replace-
ment filter.Follow the installation instructions printed onthe filter.
N00937801594
The engine coolant rese
rve tank (A) lets you
quickly see when you need to add coolant.When the engine is cold, the level of the cool-ant in the reserve tank should be between theFULL and LOW marks. The radiator usuallystays full so there is no reason to remove theradiator cap (B) except when you check thecoolant freeze point or
replace the antifreeze
coolant.
Mitsubishi Motors Genui
ne Coolant provides
excellent protection against corrosion andrust formation on all metals, including alumi-num, and prevents clogs in some parts ofengine.If you need to add coolant often, or if thelevel in the reserve tank does not drop whenthe engine cools, the cooling system shouldbe pressure-tested for le
aks. Take your vehi-
cle to an authorized Mitsubishi Motors dealeror a repair facility of
your choice for testing.
Engine coolant To check the coolant level
*: Front of the vehicleTo add coolant Use “Mitsubishi Motors
Genuine Super Long
Life Coolant Premium” or equivalent
*.
*: similar high quality et
hylene glycol based
non-silicate, non-amine, non-nitrate andnon-borate coolant with long life hybridorganic acid technologyCAUTIONDo not use alcohol or methanol antifreeze orany engine coolants th
at contain them. Using
the wrong antifreeze can corrode aluminumparts.
BK0249100US.book 8 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Transfer oil (All-w
heel drive models)
9-12 Vehicle care and maintenance
9
Do not use any fluid additives to the trans-mission.
N00938401311
Whenever the transfer oil level is checked,add oil as necessary to maintain the properlevel. Fill with the oil according to the tablebelow.
N00915201309
Whenever the oil level is checked, add oil asnecessary to maintain the proper level.Fill with the oil according to the table below.
N00938601342
The windshield and rear window washer fluidreservoir is in the
engine compartment.
Check the washer fluid
level at regular inter-
vals and add washer fluid to reservoir if nec-essary.Open the reservoir cap and check the fluidlevel with the dipstick.When freezing weather is anticipated, flushout the water in the reservoir by operating thepump. Fill the reservoi
r with windshield anti-
freeze (not radiator an
tifreeze), and operate
the system for a few seconds to flush out theresidual water.
CAUTIONUsing the improper transaxle fluid may dam-age the transaxle.
Special additives

Transfer oil (All-wheel drive models) Fluid type Lubricant
Mitsubishi Motors Genuine Super Hypoid Gear Oil API
GL-5
Viscosity range
SAE 80
Rear axle oil (All-wheel drive models) Fluid type Lubricant
Mitsubishi Motors Genuine Super Hypoid Gear Oil API
GL-5
Viscosity range
SAE 80
Washer fluid
FULL
EMPTY
BK0249100US.book 12 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Tires9-20 Vehicle care and maintenance
9
N00939700141
The following maintenance steps are recom-mended:Check tire pressures regularly.Have regular maintenance done on thewheel balance and front and rear suspen-sion alignment.Rotate your tires regul
arly as described in
the “Tire rotation” section on page 9-20.
N00939800184
Tread wear indicators are built into the origi-nal equipment tires on
your vehicle to help
you know when your tires should be replaced.
Many states have la
ws requiring that you
replace your tires at this point.These indicators are molded into the bottomof the tread grooves and will appear when thetire tread is worn down to 1/16 inch (1.6mm).When the bands appear next to one another intwo or more places
, replace your tires.
N00939901528
To even out the wear on your tires and makethem last longer, Mitsubishi Motors Corpora-tion recommends that y
ou rotate your tires at
the mileage listed in the “WARRANTY ANDMAINTENANCE MANUAL”.However, the timing for tire rotation mayvary according to your vehicle condition,road surface conditions, and your own per-sonal driving habits. Any time you noticeunusual wear, rotate your tires as soon as pos-sible.When rotating tires,
check for uneven wear,
damage, and wheel alignment. Abnormalwear is usually caused by a wrong tire pres-
On all-wheel drive vehi
cles, always use tires
of the same size, same
type, and same brand,
and which have no wear differences. Usingtires that differ in si
ze, type, brand or the
degree of wear, will in
crease the differential
oil temperature, resul
ting in possible damage
to the driving system. Further, the drive trainwill be subjected to ex
cessive loading, possi-
bly leading to oil leakage, component sei-zure, or other serious problems.Only Mitsubishi Motors Authorized wheelsshould be used, beca
use your vehicle is
equipped with a tire pr
essure monitoring sys-
tem.Use of another type of
wheel risks air leaks
and sensor damage, as
it will not be possible
to install the tire pressure sensor properly.NOTE
On vehicles with Elec
tric parking brake, 16
inches steel wheel cannot be used on yourvehicle because it interfe
res with brake parts.
Additionally, 16 inches aluminum wheelmay not be used on your vehicle dependingon its type, even if a Mitsubishi Motors Gen-uine wheels.Consult an authorized Mitsubishi Motorsdealer before using
wheels that you have.
CAUTION
Tire maintenance Tread wear indicator 1- Location of the tread wear indicator2- Tread wear indicator
NOTE
Tire wear indicators ca
n have different marks
and locations depending
on the tire manufac-
turer.
Tire rotation
BK0249100US.book 20 ページ ２０１７年５月１０日　水曜日　午前８時４９分

For cold and snowy weather
Vehicle care and maintenance 9-25
9
The underside or rear of the vehicle isdamaged
Also check the exhaust system each time thevehicle is raised for l
ubrication, oil changes,
or required service. A
ny open seams or loose
connections could le
t dangerous exhaust
fumes seep into the luggage and passengercompartments.Check for holes or exhaust gas leakscaused by corrosion or damage.Check the joints and connections forlooseness or exhaust gas leaks.Check the rubber hangers and brackets fordamage.
N00942300079
The timing belt should be replaced with anew one at the mileage listed in the “WAR-RANTY AND MAINTENANCE MAN-UAL”.
N00942501124
The hood lock release mechanism and hoodsafety catch should be checked, cleaned, andoiled when needed for easy movement and toprevent rust and wear. Use MultipurposeGrease NLGI Grade 2 sparingly for all slidingparts of the hood latch and release lever.Work the grease into the hood lock mecha-nism until all the movable surfaces are cov-ered.Also, put a light coat
of the same grease on
the safety catch wherever moving parts touch.
N00942600102
The ventilation slots in
front of the wind-
shield should be brushed clear after a heavysnowfall so that the operation of the heatingand ventilation systems will not be impaired.
To prevent freezing of the weatherstrippingon the doors, engine hood, etc., they shouldbe treated with
silicone grease.
It is a good idea to carry a shovel or a short-handled spade in the vehicle during the win-ter so that you can clear away snow if you getstranded. A small hand-brush for sweepingsnow off the vehicle a
nd a plastic scraper for
the windshield, side a
nd rear window are also
useful.
N00942700291
The fusible links will melt to prevent a fire ifa large current attempts to flow through cer-tain electrical systems.In case of a melted fusible link, see yourauthorized Mitsubishi Motors dealer or arepair facility of your choice for inspectionand replacement.For the fusible links, please refer to “Fuseload capacities” on page 9-27.
Check for any of the following conditions: Timing belt
Hood lock release mechanism and safety catch For cold and snowy weather Ventilation slots
Weatherstripping Additional equipment (For regions where snow is encoun-tered) Fusible links
BK0249100US.book 25 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Fuses
Vehicle care and maintenance 9-29
9
*: Fusible link
SBF2 Starter 30 A*SBF3
Air condition-ing condenser fan motor
30 A*
SBF4
Radiator fan
motor
40 A*
SBF5
Anti-lock brak-ing system
40 A*
SBF6
Electric parking
brake
50 A*
SBF7
Anti-lock brak-ing system
30 A*
BF1 Power liftgate 30 ABF2
Audio system amplifier
30 A
BF3 IOD IOD 30 ABF4 Diesel 30 AF1
Automatic transaxle
20 A
F2 Wiper de-icer 15AF3
Electric parking
brake
7.5 A
F4
Daytime run-ning lights
10 A
No.
Sym-bol
Electrical sys-
tem
Capacity
F5 Front fog lights 15 AF6 Air conditioner 10 AF7
Headlight washer
20 A
F8 Security horn 20 AF9 Horn 10 AF10 ETV 15 AF11 Alternator 7.5 AF12 Engine 7.5 AF13
ENG/POWER 20 AFuel line heater 25 A
F14 Fuel pump 15 AF15 Ignition coil 10 AF16 ENG/POWER 10 AF17
Headlight (high beam) (left)
10 A
F18
Headlight (high beam) (right)
10 A
No.
Sym-bol
Electrical sys-
tem
Capacity
F19
Head-light (low beam) (left)
LED 20 A
F20
Head-light (low beam) (right)
LED 20 A
F21
Head-light (low beam) (left)
Halo-gen
10 A
F22
Head-light (low beam) (right)
Halo-gen
10 A
F23
Battery current
sensor
7.5 A
#1 — Spare fuse 10 A#2 — Spare fuse 15 A#3 — Spare fuse 20 ANo.
Sym-bol
Electrical sys-
tem
Capacity
BK0249100US.book 29 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs
Vehicle care and maintenance 9-31
9
4. Use the fuse location diagrams and thematching tables, to check the fuse that isrelated to the problem. If the fuse is notblown, something else must be causingthe problem. Have the system inspectedby your authorized Mitsubishi Motorsdealer or a repair facility of your choice.
5. Insert a new fuse
of the same capacity
securely into the appropriate slot.
N00942901391
Before replacing the bulb, be sure the light isoff. Do not touch the glass part of the newbulb with your bare fingers; the oil from yourskin will stay on the glass and dim or destroythe bulb when it gets hot.
B- Fuse is OKC- Blown fuse
CAUTIONNever use a fuse with a capacity greater thanthe one listed or any s
ubstitute, such as wire,
foil etc. This would
cause the circuit wiring
to heat up and could cause a fire.If the replacement fuse blows again after ashort time, have the electrical systemchecked by an authorized Mitsubishi Motorsdealer or a repair faci
lity of your choice to
find and correct
the cause.
Replacement of light bulbs
CAUTIONBulbs are extremely hot immediately afterbeing turned off.When replacing the bulb, wait for it to coolsufficiently before
touching it. You could
otherwise be burned.
Handle halogen light bul
b with care. The gas
inside a halogen light
bulb is highly pressur-
ized, so dropping, knocki
ng, or scratching a
halogen light bulb can
cause it to shatter.
Never hold the halogen
light bulb with a bare
hand, dirty glove, etc.The oil from your hand could cause the bulbto break the next time the headlights areused.If the glass surface is dirty, clean it withalcohol and let it dry completely beforeinstalling the bulb.CAUTIONDo not install commercially available LED-type bulbs. Commercia
lly available LED-
type bulbs could adversely affect the opera-tion of the vehicle, such as by preventing thelights and other vehicle equipment fromoperating properly.CAUTION
BK0249100US.book 31 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Cleaning the inside of your vehicle9-40 Vehicle care and maintenance
9
These can all be dangerous, and they all candamage your vehicle.
N00945200095
After washing the inside of your vehicle withany cleaner, wipe it dry in a shady, well venti-lated area.
N00945300155
1. Lightly wipe these off with a soft clothsoaked in a 3% solution of gentle soapand water.2. To rinse, dip the cloth in fresh water,wring it out well, and wipe off all thesoap.
N00945500128
1. To maintain the value of your new vehi-cle, maintain the upholstery carefully andkeep the interior clean.Use a vacuum cleaner
and brush to clean
the seats. If stained,
vinyl and synthetic
leather should be cleaned with an appro-priate cleaner. Cloth fabrics can becleaned with either upholstery cleaner or a3% solution of gentle soap in lukewarmwater.2. Clean the carpeting with a vacuumcleaner and remove any stains with carpetcleaner. Oil and grea
se can be removed by
lightly dabbing with
a clean white cloth
and spot remover.
CAUTIONCleaning products can be dangerous. Someare poisonous and othe
rs are highly flamma-
ble. Some are dangerous if you breathe theirfumes in a closed space. When you use any-thing in a container to
clean your vehicle, be
sure to follow the instructions. Always openyour vehicle doors or windows when you’recleaning the inside. Never use the followingchemicals to clean your vehicle:• Gasoline• Carbon Tetrachloride• Benzine• Kerosene• Naphtha• Acetone• Turpentine• Paint Thinner• Lacquer Thinner• Nail Polish Remover
Cleaning the inside of your vehicle
CAUTIONDo not use organic s
ubstances (solvents,
benzine, kerosene, alc
ohol, gasoline, etc.) or
alkaline or acidic solutions.These chemicals can
cause discoloring,
staining or cracki
ng of the surface.
If you use cleaners or polishing agents, makesure their ingredients do not include the sub-stances mentioned above.NOTE
Always read the instru
ctions on the cleaner
label.
Plastic, vinyl leat
her, fabric and
flocked parts
NOTE
Do not use cleaners,
conditioners, and pro-
tectants containing
silicones or wax.
Such products, when applied to the instru-ment panels or other pa
rts, may cause reflec-
tions on the windshiel
d and obscure vision.
Also, if such products get on the switches ofthe electrical accessories, it may lead to fail-ure of these accessories.
Upholstery
BK0249100US.book 40 ページ ２０１７年５月１０日　水曜日　午前８時４９分