2018 MITSUBISHI OUTLANDER light

Replacement of light bulbs9-34 Vehicle care and maintenance
9
N00901801216
1. When replacing the bulb on the left sideof the vehicle, remove the bolts (A) hold-ing down the relay box and the sub fuseblock, and then move them toward therear of the vehicle. (if so equipped)
2. Turn the cap (B) counterclockwise toremove it.3. Turn the socket (C) counterclockwise toremove it, and then pull the bulb out ofthe socket.
4. To install the bulb, perform the removalsteps in reverse.
N00900301171
• Front foot lights• Floor console box light
Headlights (low beam, halogen bulb type) *- Front of the vehicle
NOTE
*- Front of the vehicle
NOTE
When installing the bulb, align the tab (D)with the notch (E) of the socket.
Headlights (low beam, LED type)
NOTE
The headlights use an LED instead of thebulb.Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.
BK0249100US.book 34 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs
Vehicle care and maintenance 9-35
9
N00901901132
1. When replacing the bulb on the right sideof the vehicle, rem
ove the clip (A) hold-
ing down the washer tank spout and movethe spout toward the rear of the vehicle.2. Turn the cap (B) counterclockwise toremove it.
3. Turn the bulb (C) counterclockwise toremove it and then while holding downthe tab (D), pull out the bulb (E).4. To install the bulb, perform the removalsteps in reverse.
N00943201359
The alignment of th
e headlights should be
checked by an authorized Mitsubishi Motorsdealer or a repair facility of your choice.
N00915501214
1. When replacing the bulb on the left sideof the vehicle, move the relay box towardthe rear of the vehi
cle. (if so equipped)
(Refer to “Headlight
(low beam, halogen
bulb type): Step 1” on page 9-34.
2. Turn the socket (A
) counterclockwise to
remove it, and then pull the bulb out ofthe socket.3. To install the bulb, perform the removalsteps in reverse.
Headlights (high beam) *- Front of the vehicle
Headlight aim adjustment Front side-marker lights
*- Front of the vehicle
BK0249100US.book 35 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs9-36 Vehicle care and maintenance
9
N00917301724N00943401423
1. Remove the 12 clips (A, B), and thenremove the cover (C).
2. Turn the socket (D
) counterclockwise to
remove it, then remove the bulb from thesocket by turning it counterclockwisewhile pressing in.3. To install the bulb, perform the removalsteps in reverse.
N00943501189N00943601920
1. Insert a straight
blade (or minus) screw-
driver with a cloth over its tip at the pointsindicated by arrows and pry gently toremove the cover (A).
Parking lights/Daytime running lights
NOTE
The parking lights and daytime runninglights use an LED in
stead of the bulb.
Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.
Front turn signal lights
*: Front of the vehicle
Side turn signal lights
(if so
equipped)
NOTE
The side turn signal lights use an LEDinstead of the bulb. Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.
Front fog lights (Halogen bulb type)
BK0249100US.book 36 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs
Vehicle care and maintenance 9-37
9
2. Remove the 3 screws
(B) and remove the
light unit.
3. While holding down the tab (D), pull outthe socket (E).4. Turn the bulb (F) counterclockwise toremove it.5. To install the bulb, perform the removalsteps in reverse.
N00943601933N00943701598
1. Open the liftgate.2. Remove the screws (A), and then movethe light unit toward the rear of the vehi-cle to unfix the notch (B) and pins (C).
NOTE
When unfastening the screws or the foglight, be careful not to move the beam posi-tion adjustment screw (C).
Front fog lights (LED type)
NOTE
The fog lights use an
LED instead of the
bulb.Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.
Rear combination lights
BK0249100US.book 37 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs9-38 Vehicle care and maintenance
9
3. Turn the socket counterclockwise andremove it, and then pull the bulb out ofthe socket.4. To install the bulb, perform the removalsteps in reverse.
N00929101080
1. Push the light unit upward to remove it.
2. Turn the socket (A) counterclockwise toremove it, and then pull the bulb out ofthe socket.3. To install the bulb, perform the removalsteps in reverse.
D- Rear turn signal lightE- Tail light and stop light (LED) - cannot
be replacedNOTE
The rear side-marker li
ght, tail light and stop
light use an LED instead of the bulb.Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.
NOTE
When mounting the light unit, align thenotch (F) and pin (G) on the light unit withthe clip (H) and hole (I) in the body.
Back-up lights
NOTE
Wrap a cloth around the tip of the screw-driver to keep from scratching the lens.
NOTE
When installing the light unit, first insert thenotch (B) into the hole on the body, and thenpush on the light unit to fit it into place.
BK0249100US.book 38 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Vehicle care precautions
Vehicle care and maintenance 9-39
9
N00944001442
1. When removing the light unit (A), push ittoward the left side of the vehicle body.2. Use a screw driver to gently pry up the tab(B) and remove the lens.
3. Pull the bulb out of the socket.4. To install the bulb, perform the removalsteps in reverse.
N00943900102N00945100166
In order to maintain the value of your vehicle,perform regular mainte
nance using the proper
materials and procedures
. Be sure to use only
those materials and proc
edures that meet your
local environmental pollution control regula-tions. Choose the materials you will use care-fully, to be sure that they do not containcorrosives. If you are
not sure, contact an
authorized Mitsubishi Motors dealer for helpin choosing these materials.
License plate lights
NOTE
Wrap a cloth around the tip of the screw-driver to keep from scratching the lens.
NOTE
When mounting the light unit, insert tab (C)first then align tab (D) with its hole.
High-mounted stop light
NOTE
The high-mounted stop light uses an LEDinstead of the bulb. Check with an authorizedMitsubishi Motors dealer or a repair facilityof your choice when the light needs to berepaired or replaced.
Vehicle care precautions
BK0249100US.book 39 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Cleaning the inside of your vehicle9-40 Vehicle care and maintenance
9
These can all be dangerous, and they all candamage your vehicle.
N00945200095
After washing the inside of your vehicle withany cleaner, wipe it dry in a shady, well venti-lated area.
N00945300155
1. Lightly wipe these off with a soft clothsoaked in a 3% solution of gentle soapand water.2. To rinse, dip the cloth in fresh water,wring it out well, and wipe off all thesoap.
N00945500128
1. To maintain the value of your new vehi-cle, maintain the upholstery carefully andkeep the interior clean.Use a vacuum cleaner
and brush to clean
the seats. If stained,
vinyl and synthetic
leather should be cleaned with an appro-priate cleaner. Cloth fabrics can becleaned with either upholstery cleaner or a3% solution of gentle soap in lukewarmwater.2. Clean the carpeting with a vacuumcleaner and remove any stains with carpetcleaner. Oil and grea
se can be removed by
lightly dabbing with
a clean white cloth
and spot remover.
CAUTIONCleaning products can be dangerous. Someare poisonous and othe
rs are highly flamma-
ble. Some are dangerous if you breathe theirfumes in a closed space. When you use any-thing in a container to
clean your vehicle, be
sure to follow the instructions. Always openyour vehicle doors or windows when you’recleaning the inside. Never use the followingchemicals to clean your vehicle:• Gasoline• Carbon Tetrachloride• Benzine• Kerosene• Naphtha• Acetone• Turpentine• Paint Thinner• Lacquer Thinner• Nail Polish Remover
Cleaning the inside of your vehicle
CAUTIONDo not use organic s
ubstances (solvents,
benzine, kerosene, alc
ohol, gasoline, etc.) or
alkaline or acidic solutions.These chemicals can
cause discoloring,
staining or cracki
ng of the surface.
If you use cleaners or polishing agents, makesure their ingredients do not include the sub-stances mentioned above.NOTE
Always read the instru
ctions on the cleaner
label.
Plastic, vinyl leat
her, fabric and
flocked parts
NOTE
Do not use cleaners,
conditioners, and pro-
tectants containing
silicones or wax.
Such products, when applied to the instru-ment panels or other pa
rts, may cause reflec-
tions on the windshiel
d and obscure vision.
Also, if such products get on the switches ofthe electrical accessories, it may lead to fail-ure of these accessories.
Upholstery
BK0249100US.book 40 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Cleaning the outside of your vehicleVehicle care and maintenance 9-41
9
N00945600187
1. To clean, lightly wi
pe the leather with a
soft cloth soaked in a 5% solution of gen-tle soap and water.2. To rinse, dip the cloth in fresh water,wring it out well, and wipe off all thesoap.3. To preserve and protect, use a leather pro-tecting agent on the genuine leather sur-face.
N00945700058
To protect your vehicle’s
finish, wash it often
and thoroughly. If desired, you may wax yourvehicle using a nonabrasive automobile wax.
N00945800033
Industrial pollution, road tar, bird droppings,tree sap, insect remain
s, sea water and other
foreign matters can damage the finish on yourvehicle.Generally, the longer any foreign materialstays on the finish, the worse the damage.Wash your vehicle as soon as possible when-ever the finish gets soiled.
N00945901709
Chemicals contained in the dirt and dustpicked up from air, rain, snow, or road sur-faces can damage the paint and body of yourvehicle if left on.Frequent washing and wa
xing is the best way
to protect your vehicle from this damage.Do not wash the vehicl
e in direct sunlight.
Park the vehicle in the shade and spray it withwater to remove dust.
Next, using plenty of
clean water and a car
washing mitt or sponge,
wash the vehicle from top to bottom.Use a mild car washing soap if necessary.Rinse thoroughly and wipe
dry with a cham-
ois or soft cloth. Af
ter washing the vehicle,
carefully clean the join
ts and flanges of the
doors, hood, etc., wher
e dirt is likely to
remain.
NOTE
If fuzzing is difficult to remove from the seatupholstery, draw a suitable defuzzing brushover the surface in
one direction.
Genuine leather
(if so equipped)
NOTE
If genuine leather is we
t with water, wipe it
with a dry, soft cloth. If left damp, mildewmay grow.The genuine leather su
rface can be damaged
if brushed with a nylon or synthetic fiberbrush.Organic solvents such as benzine, kerosene,alcohol, gasoline, or acid
or alkaline solvents
can discolor the genuine
leather surface and
should not be used.Genuine leather can
mildew if not kept
clean. Clean up any o
il stains immediately.
The genuine leather surface may harden andshrink if it is exposed to the direct sunlightfor long hours. When your vehicle is parked,place it in the shade as much as possible.When the temperature of the vehicle interiorrises in summer, vinyl products left on thegenuine leather seat
may deteriorate and
stick to the seat.
Cleaning the outside of your vehicle Foreign material
NOTE
Wa s h i n g
CAUTIONWhen washing the underside of your vehicleor the wheels, wear a pair of gloves to pro-tect your hands.If your vehicle is equipped with the rain sen-sor, place the wiper switch lever in the“OFF” position to
deactivate the rain sensor
before washing the vehi
cle. Otherwise, the
wipers will operate in
the presence of water
spray on the windshield and may get dam-aged as a result.
BK0249100US.book 41 ページ ２０１７年５月１０日　水曜日　午前８時４９分