2018 MITSUBISHI OUTLANDER instrument panel

Supplemental Restraint System (SRS) - airbag
Seat and restraint systems 4-45
4
The front airbags and driver’s knee airbagmay deploy if the underside of the vehiclesuffers a moderate to
severe impact (under-
carriage impact). Some typical situations areshown in the illustration.Since the front airbags and driver’s knee air-bag may deploy in ce
rtain types of unex-
pected impacts, as show
n in the illustrations,
and these unexpected impacts can move youout of position, it is
important to always wear
your seat belts properly. When worn properly,seat belts can help maintain your distancefrom the airbags when they begin to inflate.The initial stage of airbag inflation is themost forceful and can cause serious injury ordeath if you are close to the deploying airbag.The front airbags and driver’s knee airbag MAY DEPLOY when …
Collision with an elevat
ed median/island or
curbVehicle travels over a deep hole/potholeVehicle drives down a steep slope and hits the ground
WA R N I N GDo not attach anything to the steeringwheel’s padded cover, such as trim mate-rial, badges, etc. These could strike andinjure an occupant if
the airbag inflates.
Do not set anything on, or attach anythingto, the instrument
panel above the glove
compartment. Such items could strike andinjure an occupant if
the airbag inflates.
WA R N I N GDo not attach accessories to, or put themin front of, the wind
shield. They could
restrict the airbag infl
ation, or strike and
injure an occupant, when the airbaginflates.
BK0249100US.book 45 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Supplemental Restraint System (SRS) - airbag4-46 Seat and restraint systems
4
N00408101431
The side airbags (A) are contained in thedriver and front passenger seatbacks.The side airbag is de
signed to inflate only on
the side of the vehicle that is impacted, evenwith no passenger in the front seat.A label is attached to the seatbacks in vehi-cles equipped with side airbags.
Do not attach addition
al keys or accesso-
ries (hard, pointed or
heavy objects) to the
ignition key. Such objects could preventthe driver’s knee ai
rbag from inflation
normally or could be propelled to causeserious injury if
the airbag inflates.
Do not attach accessories to the lower por-tion of the driver’s side instrument panel.Such objects could prevent the driver’sknee airbag from inflating normally orcould be propelled to cause serious injuryif the airbag inflates.WA R N I N GDo not attempt to remove, install, disas-semble or repair the SRS airbags.WA R N I N G
Do not place objects,
such as packages or
pets, between the airbags and the driveror the front passenger. Such objects canadversely affect ai
rbag performance, or
cause serious injury or death when theairbag deploys.Immediately after airbag inflation, someparts of the airbag syst
em will be hot. Do
not touch them. You could otherwise beburned.The airbag system is designed to workonly once. After the
airbags deploy, they
will not work again. They must promptlybe replaced and the
entire airbag system
must be inspected by
an authorized Mit-
subishi Motors dealer.WA R N I N G
Side airbag system
BK0249100US.book 46 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Supplemental Restraint System (SRS) - airbag
Seat and restraint systems 4-51
4
• Steering wheel• Instrument panel[For vehicles so
ld in U.S.A.]
To contact Mitsubi
shi Motors North
America, Inc.call 1-888-648-7820 or write to:Mitsubishi Motors North America, Inc.Customer Relations DepartmentP.O. Box 6400Cypress, CA 90630-0064[For vehicles so
ld in Canada]
To contact Mitsubishi Motor Sales ofCanada, Inc.call 1-888-576-4878 or write to:Mitsubishi Motor Sales of Canada, Inc.Customer Relations DepartmentP.O. Box 410094141 Dixie RoadMississauga, ON L4W 5C9NOTE
[For vehicles sold in Puerto Rico]To contact Mitsubishi Motor Sales ofCaribbean, Inc.call 1-787-251-8715 or write to:Mitsubishi Motor Sales of Caribbean,Inc.Customer Service DepartmentP.O. Box 192216SAN JUAN PR 00919-2216[For vehicles
sold in Guam]
To contact Triple J Enterprises Inc.call (671) 649-3673 or write to:Triple J Enterprises, Inc.P.O. Box 6066TAMUNINGGUAM 96931[For vehicles so
ld in Saipan]
To contact Triple J Motorscall (670) 234-7133 or write to:Triple J MotorsP.O. Box 500487SAIPAN, MP96950-0487
[For vehicles sold
in American Samoa]
To contact Pacific Marketing Inc.call 684 (699) 9140 or write to:Pacific Marketing, Inc.P.O. Box 698PA G O PA G O ,AMERICAN SAMOA AS, 96799
BK0249100US.book 51 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-15
5
N00503301077
The operating range is the interior of thevehicle.
N00503401326
While carrying the F.A.S.T.-key, press thedriver’s or front passenger’s door lock/unlockswitch (A), or the liftgate LOCK switch (B)within the operating range to lock all thedoors and the liftgate.The turn signal lights will blink once and thebuzzer will sound once.Also refer to “Doors locks”, “Power doorlocks”, “Liftgate” and “Power liftgate” onpages 5-34, 5-36, 5-38 and 5-39 respectively.
Even if the F.A.S.T.-key is within about 2.3feet (70 cm) of the handle of the driver’sdoor, front passenger’s door or liftgate, thesystem may not operate if the key is close tothe ground or in a high position.If the F.A.S.T.-key is within the operatingrange, even a person not carrying theF.A.S.T.-key can lock and unlock the doorsor the liftgate by pressing the driver’s orfront passenger’s door lock/unlock switch,the liftgate LOCK switch or the liftgateOPEN switch.
Operating range for starting the engine and changing the opera-tion mode

NOTE
*: Front of the vehicle:Operating range
NOTE
Even if the F.A.S.T.-key is within the operat-ing range, it may not be possible to start theengine and change the
operation mode if the
key is in a storage space such as the glovecompartment, on top of the instrument panel,or in the door pocket or luggage compart-ment.Even if the F.A.S.T.-key is inside the vehicle,it may not be possible to
start the engine and
change the operation mode if the key is tooclose to a door or door window.
To operate using the F.A.S.T.-key

To l o c k

Driver’s and front passenger’s door lock/unlock switches
BK0249100US.book 15 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-27
5
1. Stop the vehicle.2. Fully engage the parking brake whiledepressing the brake pedal.3. Move the selector lever to the “P”(PARK) position, and then press theengine switch to
stop the engine.
N00568301083
Insert the F.A.S.T.-key into the key slot in theinstrument panel. St
arting the engine and
changing the operation mode should be nowpossible.Remove the F.A.S.T.-key from the key slotafter starting the engine or changing the oper-ation mode.
Warning display (color liquid crystal displaytype)Warning light (mono-color liquid crystal dis-play type)If the operation mode is in OFF and thedriver’s door is opened with the F.A.S.T.-keyin the key slot, a warning is issued with thewarning display and the buzzer buzzing for
NOTE
If you have to bring the engine to an emer-gency stop while drivi
ng, press and hold the
engine switch for 3 sec
onds or more, or press
it quickly 3 times or more. The engine willstop and the operation mode will go to ACC.Do not stop the engine wi
th the selector lever
in any position other than the “P” (PARK)position. If the engine
is stopped with the
selector lever in any
position other than the
“P” (PARK) position, the operation modewill go to ACC rather than OFF.Put the operation mode
in OFF after placing
the selector lever in the

Combination headlights and dimmer switch
Features and controls 5-209
5
[When the engine is not
running, or when the
engine is running but the parking brake is notreleased]The engine starts when the lights are off.
N00532601649
If the following operation is performedwith the combination headlights and dim-mer switch in the “ ” or “ ” position,the lights automatically turn off.[Except for vehicles equipped with theF. A . S . T. - k e y ]The ignition switch is turned to the “OFF”
the key is removed
from the ignition switch and the driver’sdoor is opened.[For vehicles equipped with the F.A.S.T.-key]The operation mode is changed to OFF orACC and the driver’s door is opened.If the following operation is performedwith the combination headlights and dim-mer switch in the “ ” or “ ” position,the lights automatically turn off afterapproximately 3 minutes.[Except for vehicles equipped with theF. A . S . T. - k e y ]The ignition switch is turned to the “OFF”
the key is removed
from the ignition switch and the driver’sdoor is not opened.
The daytime running lights illumi-natedTail, front and re
ar side-marker
lights, license pl
ate, instrument
panel lights and downlight onHeadlights and other lights on
NOTE
Once the daytime running light come on,they do not go out until the ignition switch isturned to the “OFF” or “ACC” position orthe operation mode is changed to OFF orACC.OFF All lights offAUTO
Headlights and other lights turn on and off automatically in accor-dance with outside light level.Parking, tail, front
and rear side-
marker lights, license plate, instru-ment panel lights and downlight onHeadlights and other lights on
NOTE
The sensitivity of the automatic on/off con-trol can be adjusted.For further informati
on, please contact your
authorized Mitsubishi
Motors dealer or a
repair facility
of your choice.
On vehicles equippe
d with the Smartphone
Link Display Audio, sc
reen operations can
be used to make the adjustment.Refer to the separate
owner’s manual for
details.Do not cover the sensor (A) for the automaticon/off control by affixing
a sticker or label to
the windshield.If the lights do not turn on or off with theswitch in the “AUTO”operate the switch. Have the system checkedby an authorized Mitsubishi Motors dealer ora repair facility of your choice.
Light auto-cutout function (headlights and other lights)
BK0249100US.book 209 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Combination headlights and dimmer switch
Features and controls 5-211
5
light in the instrument
cluster i
ndicates when
the headlights are on high beam.
N00550001209
You can flash the high beams by pulling thelever gently toward you (2). The lights willgo back to normal when you let go. While thehigh beam is on, you will see a blue light onthe instrument panel.
N00591300028
The automatic high beam
system turns the
high beam light on or
off automatically
according to surrounding light conditions.The sensor (A) detects lights, such as thelights of an oncoming
vehicle, a vehicle
ahead or street lights.
N00593600038
1. Rotate the light switch to “ ” positionor “AUTO” position when the engine isrunning.2. Press the automatic high beam systemswitch.The automatic high beam system is acti-vated and the indicator is illuminated.If the automatic high beam system switchis pressed again, the automatic high beamsystem will be deac
tivated and automatic
high beam system indicator will go off.
Headlight flasher
NOTE
You can flash the high beams by pulling thelever toward you, even if the light switch isoff.
If you turn the lights off with the head lightsset to high-beam illumin
ation, the headlights
are automatically returned to their low-beamsetting when the light
switch is next turned
to the “ ” position.
Automatic high beam system
(if
so equipped)
NOTE
WA R N I N GDo not rely solely on the Automatic HighBeam. Always observe surrounding trafficand light conditions. If necessary, manu-ally turn the high beams on or off.Refer to “Dimmer (high/low beamchange)” on page 5-210.
How to use the automatic high beam system

NOTE
If the headlights are on when the light switchis in the “AUTO” position, the automatichigh beam system works.
BK0249100US.book 211 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Turn signal lever
Features and controls 5-217
5
N00522601590
When changing lanes, or
to making a gradual
turn, hold the lever in the “lane change” posi-tion (1). It will return
to the neutral position
when you let go. Use the full position (2)when making a normal turn. The lever willreturn to the neutral position when the turn iscomplete. There may be times when the leverdoes not return to the neutral position. Thisusually happens when the steering wheel isturned only slightly. You
can easily return the
lever by hand.Also, when you move the lever to (1) slightlythen release it, the turn signal lights and theindicator light in the instrument cluster willflash three times.
Keep the knob in the “0” position exceptwhen using the knob to lower the headlightbeam angle.Always return the knob to the “0” positionwhen the load is removed and the peoplehave left
the vehicle.
NOTE
Turn signal lever
NOTE
A light in the instrument panel flashes toshow when the front and rear turn signallights are working properly.If this light flashes fa
ster than usual, check
for a burned out turn signal light bulb or mal-functioning connection in the signal.If the panel light does not come on when thelever is moved, check for a blown fuse or aburned out bulb in the panel.Have the system inspected by your autho-rized Mitsubishi Motors dealer or a repairfacility of your choice.It is possible to modi
fy functions as follows:
• Deactivate the turn signal light 3-flashfunction for lane changes.• Adjust the time required to operate thelever for the 3-flash function.See your authorized Mitsubishi Motorsdealer for details.For vehicles equipped with the SmartphoneLink Display Audio, adjustments can bemade using screen ope
rations. For further
details, refer to the
separate owner’s manual.
It is possible to change the tone of a sound-ing buzzer as the turn signal lights flash.[Vehicle equipped with the multi informationdisplay - type 1]Refer to “Changing the turn-signal sound”on page 5-172.[Vehicle equipped with the multi informationdisplay - type 2]See your authorized Mitsubishi Motorsdealer for details.
BK0249100US.book 217 ページ ２０１７年５月１０日　水曜日　午前８時４９分