2018 MITSUBISHI OUTLANDER battery

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-21
5
Fall of battery voltage
Inner buzzer sounds once
Blinks
No sounds The battery of the F.A.S.T.-key is
run down.
The warning is not activated if the battery is completely dead.
F. A . S . T. - k e y take-out mon-itoring system
Inner buzzer sounds onceOuter buzzer sounds intermit-tently
Blinks
Inner buzzer sounds onceOuter buzzer sounds intermit-tently
When the vehicle is parked with the operation mode in any mode other than OFF, if you close the door after opening any of the doors and taking the F.A.S.T.-key out of the vehicle, a warning is issued until the F.A.S.T.-key is detected in the vehicle.
•The F.A.S.T.-key take-out moni-toring system does
not function if
the F.A.S.T.-key is removed through a window without open-ing a door.This setting can be changed.Contact an authorized Mitsubishi Motors dealer for details.•The warning may display even if the F.A.S.T.-key is in the operating range for starting the engine and changing the operation mode. The surrounding environment or elec-tromagnetic waves may make it impossible to verify the ID codes of the F.A.S.T.-key and vehicle.
Item
Ty p e 1
Ty p e 2
Solution
Note
Display
Buzzer
Indicator
Buzzer
BK0249100US.book 21 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-25
5
N00514601399
The operation mode can be in any modeto start the engine.The starter motor will be turning for up toapproximately 15 seconds if the engineswitch is released at once. Pressing theengine switch again while the startermotor is still turning will stop the startermotor.The starter motor will be turning for up toapproximately 30 seconds while theengine switch
is pressed.
If the engine does not start, wait for awhile and then attempt to start the engineagain. Trying repeatedly with the engineor starter motor still turning will damagethe starter mechanism.If the engine will not start because the bat-tery is weak or discharged, refer to“Jump-starting the engine” on page 8-2for instructions.A longer warm up period will only con-sume extra fuel.The engine is warmed up enough for driv-ing when the bar graph of engine coolanttemperature display starts to move or thelow coolant temperature indicator goesout. Refer to “Engine
coolant temperature
display” on page 5-161 or “Low coolanttemperature indica
tor” on page 5-202.
Your vehicle is equipped with an electroni-cally controlled fuel injection system. Thissystem automatically controls fuel injection.There is usually no need
to depress the accel-
erator pedal when starting the engine.To prevent battery drai
n, wait a few seconds
between attempts to restart the engine.1. Make sure all occupants are properlyseated with seat belts fastened.2. Make sure the parking brake is applied.3. Press and hold the brake pedal downfirmly with your right foot.4. Make sure the selector
lever is in the “P”
If there is a fault in the steering wheel lock,the warning display will
appear. Immediately
stop the vehicle in a sa
fe place and contact
an authorized Mitsubishi Motors dealer.Warning display
Starting and stopping the engine

Tips for starting

NOTE
WA R N I N GNever run the engine in
a closed or poorly
ventilated area any longer than is neededto move your vehicle
out of the area. Car-
bon monoxide gas, wh
ich is odorless and
extremely poisonous, could build up andcause serious injury or death.CAUTIONDo not push-start the vehicle.
Do not run the engine at high rpms or driveat high speeds until the engine has had achance to warm up.
Starting the engine

NOTE
After the engine has not started for a while,the brake pedal effort needed to start theengine may become grea
ter. If this occurs,
depress the brake pedal more firmly thanusual.CAUTION
BK0249100US.book 25 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Free-hand Advanced
Security Transmitter (F.A.S
.T.-key) (if so equipped)
5
approximately 3 seconds to remind you toremove the key.
N00514800017N00515201158
The emergency key is built into the F.A.S.T.-key.When the F.A.S.T.-key cannot be used, suchas when the battery of the F.A.S.T.-key or thevehicle has run down, the emergency key canbe used to lock and unlock the driver’s door.To use the emergency key (A), unlock thelock knob (B) and remove it from theF.A.S.T.-key (C).
Turn the emergency key toward the front ofthe vehicle to lock the door. After checkingthat the door is locked, turn the emergencykey back to the center and remove it.
N00529600055
The electronic immobilize
r is designed to sig-
nificantly reduce the
possibility of vehicle
theft. The purpose of the system is to immo-bilize the vehicle if
an invalid start is
attempted. A valid st
art attempt can only be
achieved (subject to ce
rtain conditions) using
a F.A.S.T.-Key “registered” to the immobi-lizer system.All of the keys provided with your new vehi-cle have been program
med to the vehicle’s
electronics.
N00561000042
Only the F.A.S.T.-keys that have been pro-grammed to the vehicl
e’s electronics can be
used to start the vehicle.If you lose the F.A.S.T.-key, you can order aF.A.S.T.-key from your authorized MitsubishiMotors dealer by refe
rring to the key number.
To prevent vehicle theft, take your vehicleand the remaining F.A.S.T.-keys to an autho-rized Mitsubishi Motors
dealer to have the ID
codes reprogrammed.
To operate without using the F. A . S . T. - k e y

Emergency key

NOTE
Only use the emergency key in an emer-gency. When the battery of the F.A.S.T.-keyhas run down, replace
the battery as soon as
possible and use it as a F.A.S.T.-key again.After using the emergency key, be sure toreinsert it into the F.A.S.T.-key.
Locking and unlocking the driver’s door1- Insert or remove
the emergency key
2- Lock3- Unlock
Electronic immobilizer (Anti-theft starting system)

Replacement F.A.S.T.-keys

BK0249100US.book 28 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-33
5
N00562001062
N00562101076
1. Before replacing the battery, remove staticelectricity from your body by touching ametal grounded object.2. With the Mitsubishi mark facing you,insert the cloth-covered tip of a flat bladescrewdriver into the notch in the case anduse it to open the case.3. Remove the old battery.
If the UNLOCK button (2) is pressed whenall doors and the liftgate are locked and nodoors or the liftgate are opened withinapproximately 30 seconds, the doors and theliftgate will automatically re-lock.On a vehicle equipped with the SmartphoneLink Display Audio, the functions can beadjusted on the screen. For details, refer tothe separate owner’s manual.If the following conditions are observed afterpressing the LOCK (1) or UNLOCK (2) but-ton on the remote control transmitter, thebattery in the F.A.S.T.-key may need to bereplaced.• The doors and the liftgate cannot be lockedor unlocked.• The panic alarm
cannot be operated.
• The indicator light
(5) is dim or does not
come on.
If you lose your F.A.S.T.-key, please contactan authorized Mitsubishi Motors dealer for areplacement.If you wish to obtain an additional F.A.S.T.-key, please contact an
authorized Mitsubishi
Motors dealer. A maximum of four F.A.S.T.-key can be programmed for your vehicle.To use the new remote control transmitters, itis necessary to register the key with both theelectronic immobilizer
and keyless entry sys-
tem.Also refer to “Electr
onic immobilizer (Anti-
theft starting system): Customer F.A.S.T.-key programming” on page 5-29.NOTE
General information

Your F.A.S.T.-key operates on a radio fre-quency subject to Fe
deral Communications
Commission (FCC) Rules (For vehicles soldin U.S.A.) and Industr
y Canada Rules (For
vehicles sold in Canada). This device com-plies with Part 15 of FCC Rules and IndustryCanada licence-exem
pt RSS standard(s).
Operation is subject to
the following two con-
ditions.
•This device may
not cause harmful
interference.•This device must ac
cept any interference
received, including interference thatmay cause undesired operation.CAUTIONChanges or modifica
tions not expressly
approved by the manufacturer for compli-ance could void the user’s authority to oper-ate the equipment.
Procedure for replacing the remote control transmitter bat-tery
NOTE
Be sure to perform the procedure with theMitsubishi mark facing you. If the Mitsubi-shi mark is not facing you when you open thecase, the transmitter may come out.
BK0249100US.book 33 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Door locks5-34 Features and controls
5
4. Install a new battery with the +side (A)5. Close the case firmly.6. Check the keyless entry system to see thatit works.
N00509201544
Turn the key toward the front of the vehicle tolock the door. After checking that the door islocked, turn the key back to the center andremove it.
NOTE
You may purchase a re
placement battery at
an electric appliance store.An authorized Mitsubishi Motors dealer canreplace the battery for you if you prefer.CAUTIONWhen the remote control transmitter case isopened, be careful to
keep water, dust, etc.
out. Also, do not touch the internal compo-nents.
+ side- side
Coin type bat-tery CR2032
Door locks
WA R N I N GMake sure all doors are tightly closed andlocked while driving.• Locked doors, in co
mbination with the
use of seat belts, can help reduce the riskof ejection in
an accident.
• Locked doors can help keep passengers,especially small children, from openingdoors and falling out
of moving vehicles.
• Locked doors can help
prevent outsiders
from gaining access to your vehicle whenyou slow or come to a stop.
Lock your vehicle when
ever you leave it.
Children who get into
unlocked vehicles
may not be able to get out. Childrentrapped inside vehicles can quickly beovercome by heat
and suffer serious
injury or death due to heat stroke.Never leave a ch
ild alone in the vehicle. In
addition to the risk
of heat stroke, chil-
dren can activate switches and controls,resulting in an injury
or fatal accident.
When closing a door,
make sure that the
door is fully closed and the door-ajarwarning display goes
out on the informa-
tion screen on the multi-information dis-play. If the door is aj
ar it could open while
driving and cause an accident.
To lock and unlock with the key (driver’s door) 1- Insert or remove the key2- Lock3- Unlock
BK0249100US.book 34 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Liftgate (except for vehicles e
quipped with the power liftgate)
5-38 Features and controls
5
door can be opened using the inside door han-dle.
N00510101282
1. After unlocking, push the liftgate openswitch (A) and raise the liftgate.
WA R N I N GAlways keep the door
s tightly closed and
locked when driving. An unlocked doormay be accidentally
opened by a passen-
ger, especially by
a child who could fall
out. Also, if the doors are not locked, thereis a greater risk of someone being thrownfrom the vehicle
in an accident.
Liftgate (except for vehicles equipped with the power liftgate)
WA R N I N GIt is dangerous to drive with the liftgateopen since carbon mo
noxide (CO) gas can
enter the passenger compartment.CO is an invisible, odorless gas that cancause unconsciousness and even death.When opening and cl
osing the liftgate,
make sure that there are no people nearbyand be careful not to hit your head orpinch your hands, neck, etc.If snow or ice has ac
cumulated on the lift-
gate, remove it before
opening the liftgate.
Otherwise the liftgate may abruptly closedue to the weight of the snow or ice.
When opening the lift
gate, always fully
open it. A partially opened liftgate canunexpectedly close due to its own weight.When the vehicle is parked on a slope, theeffort required to open or close the liftgatemay be greater or less than expected.The liftgate may also open or close morequickly.CAUTIONDo not stand behind the exhaust pipe whenloading and unloading
luggage. Heat from
the exhaust could lead to burns.To avoid damage to the liftgate, make surethat area above and behind the liftgate isclear before opening it.NOTE
Locking and unlocking the doors by usingpower door locks (driver and front passengerside), keyless entry system, or F.A.S.T.-keyoperation (vehicles
equipped with the
F.A.S.T.-key) also locks and unlocks the lift-gate.
To open
WA R N I N G
CAUTIONMake sure there is no one standing nearbywhen opening the liftgate.NOTE
The liftgate cannot be rais
ed if it is not raised
immediately after pressing the liftgate openswitch.If this happens, raise th
e liftgate again after
pressing the liftgate open switch.It is not possible to open the liftgate whilethe battery is disconnect
ed. If necessary, use
the inside liftgate release.When the battery is reconnected, all doorsand the liftgate will be locked. Unlock thembefore trying to open the liftgate.
BK0249100US.book 38 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Power liftgate (if so equipped)Features and controls 5-41
5
N00576100038
The power liftgate ca
n be opened automati-
cally when all of the
following conditions are
met.The operation mode is in OFF.The power liftgate is completely closed.The power liftgate is unlocked.
The operation mode is in ON with theselector lever in the “P” (PARK) position.
The power liftgate is completely closed.The power liftgate is unlocked.
The power liftgate is unlocked.The F.A.S.T.-key is within the operatingrange (2.3 feet (70 cm) from the powerliftgate open switch) and the power lift-gate is locked.
The power liftgate can be closed automati-cally when all of the following conditions aremet.The operation mode is in OFF.The power liftgate is completely open.Nothing is touching th
e auto reverse sen-
sors (A) on the power liftgate.
CAUTIONDo not apply excessive force to the powerliftgate when opening or closing it. Doing socould damage to th
e power liftgate.
NOTE
Do not start the engine while the power lift-gate is operating. The sudden operation pre-vention mechanism c
ould operate, making
the power liftgate stop intermittently while itmoves.The power liftgate cannot be opened whenthe battery is discha
rged or disconnected.
The liftgate must be then opened using theinside liftgate release.Refer to “Inside lift
gate release” on page
5-46.If the keyless entry system or close switch isoperated when the pow
er liftgate main
switch is off, the warning buzzer sounds 4times to notify the driver that the power lift-gate cannot
be operated.
The power liftgate does not operate normallyunder the following conditions:• When parked on an incline• In strong winds• When the power liftga
te is covered with
snow
Repeated continuous
opening and closing
operation of the power lif
tgate will activate a
built-in protection ci
rcuit and switch the
power liftgate to
manual operation.
If one of the power lift
gate switches is oper-
ated while the power lift
gate is operating, the
power liftgate will reve
rse and return to the
full open or close position.If the selector lever is moved from “P”the power liftgate is operating or completelyopen, a warning buzzer will sound forapproximately 10 sec
onds to notify the
driver that the power liftgate is open.If the battery or fuse is replaced while thepower liftgate is open,
it cannot be closed
automatically.In this case close the power liftgate manu-ally.
Operating conditions

NOTE
BK0249100US.book 41 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Power liftgate (if so equipped)Features and controls 5-45
5
To close the power liftgate, pull the powerliftgate grip (B) dow
nward and release it
before the power liftgate is completelyclosed, and then gently close the power lift-gate from the outside.
N00576400028
The power liftgate easy closer is designed tohelp the power liftgate close securely.If the power liftgate is closed to a positionwhere it is detected as being ajar, it closesautomatically.
WA R N I N GWhen the power liftgate is closed manu-ally, the auto reverse mechanism will notoperate even if so
mething is trapped
under the liftgate.CAUTIONMake sure there is no one around the powerliftgate when opening it.NOTE
The liftgate cannot be opened if it is notraised immediately after pressing the powerliftgate open switch.If this happens, raise the liftgate again afterpressing the liftgate open switch.
When the battery is discharged or discon-nected, the power liftgate cannot be openedeven manually. At that time, the liftgate canbe opened only by using the inside liftgaterelease. Refer to “Inside liftgate release” onpage 5-46.CAUTIONThe auto reverse mechanism will not operatewhen the power liftgate
is closed manually.
Therefore be especially careful not to trap ahand or finger.NOTE
Do not fully close the power liftgate withyour hand still on the power liftgate grip.Doing so could trap and injure your hand orarm.
Power liftgate easy closer

WA R N I N GKeep your hands and fingers away fromthe power liftgate while the power liftgateeasy closer is activated. To return thepower liftgate to the sl
ightly ajar position
while the power liftgate easy closer is acti-vated, press the power liftgate openswitch.CAUTIONDo not touch the latch (A) on the inside ofthe power liftgate. Th
e power liftgate easy
closer could operate
and catch your fingers.
CAUTION
BK0249100US.book 45 ページ ２０１７年５月１０日　水曜日　午前８時４９分