2018 MITSUBISHI OUTLANDER III oil type

How to change a tire8-10 For emergencies
8
5. Remove the wheel nuts with the wheel nutwrench, then take the wheel off.6. Clean out any mud, etc. on the hub sur-face (F), hub bolts (G)
or in the installa-
tion holes (H) in the wheel, and thenmount the spare tire.
7. Turn the wheel nut clockwise by hand toinitially tighten them.[Type 1: On vehicles
with steel wheels]
Temporarily tighten the wheel nuts byhand until the tapered parts of the wheelnuts make light contac
t with the seats of
the wheel holes and the wheel is notloose.[Type 2: On vehicles with aluminiumwheels]Temporarily tighten the wheel nuts byhand until the flange parts of the wheelnuts make light cont
act with the wheel
and the wheel is not loose.
CAUTIONHandle the wheel carefully when changingthe tire, to avoid scratching the wheel sur-face.WA R N I N GMount the spare wheel with the valve stem(I) facing outward. If
you cannot see the
valve stem (I), you
have installed the
wheel backwards.Operating the vehicle with the spare wheelinstalled backwards can cause vehicledamage and result
in an ac
cident.
NOTE
Flange nuts can be te
mporarily used on the
compact spare wheel as shown in the illustra-tion, but return to the original wheel and tireas soon as possible.CAUTIONNever apply oil to either the wheel bolts orthe nuts or they will tighten too much.
Type 1Type 2
BK0249100US.book 10 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Transfer oil (All-w
heel drive models)
9-12 Vehicle care and maintenance
9
Do not use any fluid additives to the trans-mission.
N00938401311
Whenever the transfer oil level is checked,add oil as necessary to maintain the properlevel. Fill with the oil according to the tablebelow.
N00915201309
Whenever the oil level is checked, add oil asnecessary to maintain the proper level.Fill with the oil according to the table below.
N00938601342
The windshield and rear window washer fluidreservoir is in the
engine compartment.
Check the washer fluid
level at regular inter-
vals and add washer fluid to reservoir if nec-essary.Open the reservoir cap and check the fluidlevel with the dipstick.When freezing weather is anticipated, flushout the water in the reservoir by operating thepump. Fill the reservoi
r with windshield anti-
freeze (not radiator an
tifreeze), and operate
the system for a few seconds to flush out theresidual water.
CAUTIONUsing the improper transaxle fluid may dam-age the transaxle.
Special additives

Transfer oil (All-wheel drive models) Fluid type Lubricant
Mitsubishi Motors Genuine Super Hypoid Gear Oil API
GL-5
Viscosity range
SAE 80
Rear axle oil (All-wheel drive models) Fluid type Lubricant
Mitsubishi Motors Genuine Super Hypoid Gear Oil API
GL-5
Viscosity range
SAE 80
Washer fluid
FULL
EMPTY
BK0249100US.book 12 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Tires9-20 Vehicle care and maintenance
9
N00939700141
The following maintenance steps are recom-mended:Check tire pressures regularly.Have regular maintenance done on thewheel balance and front and rear suspen-sion alignment.Rotate your tires regul
arly as described in
the “Tire rotation” section on page 9-20.
N00939800184
Tread wear indicators are built into the origi-nal equipment tires on
your vehicle to help
you know when your tires should be replaced.
Many states have la
ws requiring that you
replace your tires at this point.These indicators are molded into the bottomof the tread grooves and will appear when thetire tread is worn down to 1/16 inch (1.6mm).When the bands appear next to one another intwo or more places
, replace your tires.
N00939901528
To even out the wear on your tires and makethem last longer, Mitsubishi Motors Corpora-tion recommends that y
ou rotate your tires at
the mileage listed in the “WARRANTY ANDMAINTENANCE MANUAL”.However, the timing for tire rotation mayvary according to your vehicle condition,road surface conditions, and your own per-sonal driving habits. Any time you noticeunusual wear, rotate your tires as soon as pos-sible.When rotating tires,
check for uneven wear,
damage, and wheel alignment. Abnormalwear is usually caused by a wrong tire pres-
On all-wheel drive vehi
cles, always use tires
of the same size, same
type, and same brand,
and which have no wear differences. Usingtires that differ in si
ze, type, brand or the
degree of wear, will in
crease the differential
oil temperature, resul
ting in possible damage
to the driving system. Further, the drive trainwill be subjected to ex
cessive loading, possi-
bly leading to oil leakage, component sei-zure, or other serious problems.Only Mitsubishi Motors Authorized wheelsshould be used, beca
use your vehicle is
equipped with a tire pr
essure monitoring sys-
tem.Use of another type of
wheel risks air leaks
and sensor damage, as
it will not be possible
to install the tire pressure sensor properly.NOTE
On vehicles with Elec
tric parking brake, 16
inches steel wheel cannot be used on yourvehicle because it interfe
res with brake parts.
Additionally, 16 inches aluminum wheelmay not be used on your vehicle dependingon its type, even if a Mitsubishi Motors Gen-uine wheels.Consult an authorized Mitsubishi Motorsdealer before using
wheels that you have.
CAUTION
Tire maintenance Tread wear indicator 1- Location of the tread wear indicator2- Tread wear indicator
NOTE
Tire wear indicators ca
n have different marks
and locations depending
on the tire manufac-
turer.
Tire rotation
BK0249100US.book 20 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs
Vehicle care and maintenance 9-31
9
4. Use the fuse location diagrams and thematching tables, to check the fuse that isrelated to the problem. If the fuse is notblown, something else must be causingthe problem. Have the system inspectedby your authorized Mitsubishi Motorsdealer or a repair facility of your choice.
5. Insert a new fuse
of the same capacity
securely into the appropriate slot.
N00942901391
Before replacing the bulb, be sure the light isoff. Do not touch the glass part of the newbulb with your bare fingers; the oil from yourskin will stay on the glass and dim or destroythe bulb when it gets hot.
B- Fuse is OKC- Blown fuse
CAUTIONNever use a fuse with a capacity greater thanthe one listed or any s
ubstitute, such as wire,
foil etc. This would
cause the circuit wiring
to heat up and could cause a fire.If the replacement fuse blows again after ashort time, have the electrical systemchecked by an authorized Mitsubishi Motorsdealer or a repair faci
lity of your choice to
find and correct
the cause.
Replacement of light bulbs
CAUTIONBulbs are extremely hot immediately afterbeing turned off.When replacing the bulb, wait for it to coolsufficiently before
touching it. You could
otherwise be burned.
Handle halogen light bul
b with care. The gas
inside a halogen light
bulb is highly pressur-
ized, so dropping, knocki
ng, or scratching a
halogen light bulb can
cause it to shatter.
Never hold the halogen
light bulb with a bare
hand, dirty glove, etc.The oil from your hand could cause the bulbto break the next time the headlights areused.If the glass surface is dirty, clean it withalcohol and let it dry completely beforeinstalling the bulb.CAUTIONDo not install commercially available LED-type bulbs. Commercia
lly available LED-
type bulbs could adversely affect the opera-tion of the vehicle, such as by preventing thelights and other vehicle equipment fromoperating properly.CAUTION
BK0249100US.book 31 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Capacity11-8 Specifications
11
Transfer oil
Vehicles without S-
AWC .50 qt (0.47 L)
Mitsubishi Motors Genuine S
uper Hypoid Gear Oil API GL-5
SAE 80
Vehicles with S-AW
C .48 qt (0.45 L)
Differential
Rear axle .42 qt (0.4 L)
Mitsubishi Motors Genuine S
uper Hypoid Gear Oil API GL-5
SAE 80
Brake As required Conforming to Brake fluid DOT3 or DOT4Hood lock release mechanism and safety catch A
s required Multipurpose type
grease NLGI Grade 2
Engine coolant{Includes .69 qt (0.65 L) in reserve tank}
2.4 liter models 6.3 qt (6.0 L)
Mitsubishi Motors Genuine
Super Long Life Coolant
Premium or equivalent
*
3.0 liter models 9.5 qt (9.0 L)
Washer fluid 4.8 qt (4.5 L) —
Refer to the “Air con-ditioning label” on
page 11-2.
HFO-1234yf
*:similar high quality ethylene
glycol based non-silicate, non-amine, non-nitrate
and non-borate coolant with long life hybrid o
rganic acid tech-
nology
Item
Capacity
Lubricants
BK0249100US.book 8 ページ ２０１７年５月１０日　水曜日　午前８時４９分