2018 MERCEDES-BENZ SL CLASS keyless

Problem
Possible causes/consequences and P Solutions
The engine cannot be
started using the Smart-
Key. The on-board voltage is too low. X
Switch off non-essential consumers, e.g. seat heating or interior
lighting, and try to start the engine again.
If this does not work: X
Check the starter battery and charge it if necessary ( Y
page 253).
or X
Jump-start the vehicle ( Y
page 253).
or X
Consult aq ualified specialist workshop.
The engine cannot be
started using KEYLESS-
GO. The SmartKey is in
the vehicle. The vehicle is locked. X
Unlock the vehicle and try to start the vehicle again.
The SmartKey battery is discharged or nearly discharged. X
Check the SmartKey battery ( Y
page 68) and replace it if necessary
( Y
page 68).
If this does not work: X
Start your vehicle with the SmartKey in the ignition lock.
There is interference from ap owerful source of radio waves.X
Start your vehicle with the SmartKey in the ignition lock.
You have lost aS mart-
Key. X
Have the SmartKey deactivated at aq ualified specialist workshop.X
Report the loss immediately to the vehicle insurers. X
If necessary, have the locks changed as well.
You have lost the
mechanical key. X
Report the loss immediately to the vehicle insurers. X
If necessary, have the locks changed as well.
The side windows cannot
be opened or closed
using the convenience
opening/closing fea-
ture. The SmartKey battery is discharged or nearly discharged. X
Check the SmartKey battery ( Y
page 68) and replace it if necessary
( Y
page 68).
Doors
Important safety notes
G WARNING
If children are left unsupervised in the vehicle,
they could: R
operate the vehicle's equipment. Additionally, children could set the vehicle in
motion if, for example, they: R
release the parking brake R
shift the automatic transmission out of park
position P R
start the engine
There is ar isk of an accident and injury.
Never leave children or animals unattended in
the vehicle.70
Doors
Opening and closing

When leaving the vehicle, alway st ake the
SmartKey with you and lock the vehicle. This
also applies to mobile phones if the "Digital
Car Key in smartphone" function is activated
via the Mercedes me connect web app.
Unlocking and opening doors from
the inside
! The side windows will not open/close if the
batter yisd ischarged or if the side windows
have iced up. It will then not be possible to
close the door. Do not attempt to forc et he
door closed. You could otherwise damage the
door or the side window.
You can open ad oor from inside the vehicle
even if it has been locked.
If the vehicle has previously been locked from
the outside, opening ad oor from the inside will
trigger the anti-theft alarm system. Switc ho ff
the alarm ( Y
page 64).
X
Pull door handle D .
If the door is locked, lockin gk no b C pops up.
The door is unlocked and can be opened.
When ad oor is opened, the side window on that
side opens slightly. When the door is closed, the
side window closes again.
Centrally locking and unlocking the
vehicle from the inside
You can centrally lock or unlock the vehicle from
the inside. For example, you can unlock the
front-passenger door from the inside or lock the
vehicle before you pull away. X
To unlock: press button C .X
To lock: press button D .
If the front-passenger door is closed, the vehi-
cle locks.
The central lockin gb utton does not lock or
unlock the fuel filler flap or the stowage com-
partmen tint he center console.
You cannot unlock the vehicle centrally from the
inside if the vehicle has been locked with the
SmartKey or KEYLESS-GO.
You can open ad oor from inside the vehicle
even if it has been locked.
If al ocked door is opened from the inside, the
previous unlock status of the vehicle will be
taken into consideration if: R
the vehicle was locked using the lockin gb ut-
ton for the central locking, or R
if the vehicle was locked automatically
The vehicle will be fully unlocked if it had previ-
ously been fully unlocked. If only the driver's
door had been previously unlocked, only the
door which has been opened from the inside is
unlocked.
Automatic locking feature Doors 71
Opening and closing Z

Opening/closing from outside
Opening X
Press the 6 button on the SmartKey.X
Pull handle C .X
Raise the trun kl id.
Closing
X
Pull the trun kl id down using recess C .X
Lock the vehicle if necessary using the 7
button on the key or with KEYLESS-GO.
If KEYLESS-GO detects aS martKey in the trunk,
it does not lock.
Locking the trunk separately You can lock the trun ks eparately. If you then
unlock the vehicle centrally, the trun kr emains
locked and cannot be opened. X
Close the trun kl id.X
Take the mechanical key out of the SmartKey
( Y
page 67). X
Inser tt he mechanical key into the trun kl id
lock as far as it will go. X
Turn the mechanical key clockwise from posi-
tion G to position H .X
Remove the mechanical key. X
Inser tt he mechanical key into the SmartKey.
Unlocking the trunk (mechanical key)
! The trun kl id swings upwards when opened.
Therefore, make sure that there is sufficient
clearanc ea bove the trun kl id.
If the trun kc annot be unlocked with the Smart-
Key or KEYLESS-GO, use the mechanical key.
If you use the mechanical key to unlock and
open the trun kl id, the anti-thef ta larm system
will be triggered. Switc ho ff the alarm
( Y
page 64). X
Take the mechanical key out of the SmartKey
( Y
page 67). X
Inser tt he mechanical key into the trun kl id
lock as far as it will go.
X
Turn the mechanical key from position G
counter-clockwise as far as it will go to posi- Trunk 73
Opening and closing Z

Convenience closing with KEYLESS-GO
G WARNING
When usin gt he convenience closin gf eature,
part soft he body coul dbet ra pped in th ec los-
ing area when as ide window is bein gc losed.
Ther eisar is kofi njury.
Observ et he complet ec losin gp rocedure
when th ec onvenience closin gf eature is oper-
ating. Mak es ure that no body part sa re in
close proximity durin gt he closin gp rocedure.
Procee dasf ollows if someon eist ra pped:X
Release th er ecessed sensor surface on the
door handle. X
Immediately pull and hold th ed oor handle
and keep th ed oor handle pulled.
The side windows open.
Wit hK EY LESS-GO you can close all side win-
dows simultaneously. The KEYLESS-GO key
must be outside th ev ehicle .A ll th ed oor sm ust
be closed. X
Touc hr ecessed sensor surface C on the
door handle until th es ide windows are fully
closed.
i Mak es ure you only touch recessed sensor
surface C . X
To interrup tc onvenience closing: release
recessed sensor surface C on th ed oor han-
dle.
Resetting th es id ew indowsIf as ide window can no longer be closed fully,
you must reset it. X
Close all th ed oors. X
Turn th eS ma rtKey to position G or H in the
ignition lock. X
Pull th ec orrespondin gs witch on th ed oor
control panel until th es ide window is com-
pletely closed ( Y
page 75).X
Hol dt he switch for an additional second.
If th es ide window open sa gain slightly:X
Immediately pull th ec orrespondin gs witch on
th ed oor control panel until th es ide window is
completely closed ( Y
page 75).X
Hol dt he switch for an additional second.
If th er espectiv es ide window remains closed
after th eb utto nisr eleased, then it has been
set correctly. If this is no tt he case, repeat the
steps above.
Problem sw ith th es id ew indows
G WARNING
If you close as ide window again immediately after it has been blocke dorr eset ,t he side window
closes wit hi ncreased or maximum force. The reversing feature is then no ta ctive. Part soft he
body coul dbet ra pped in th ec losin ga rea in th ep rocess. This pose sani ncreased ris kofi njury or
eve nf atal injury.
Mak es ure that no part soft he body are in th ec losin ga rea. To stop th ec losin gp rocess, release
th es witch or push th es witch again to reopen th es ide window.76
Sid ew indows
Opening and closing

Opening/closing using the SmartKey
Important safet yn otes
G WARNING
When opening or closing the roof, body parts
could be trapped by, for example, the roof
mechanism, trun kl id or side windows. There
is ar isk of injury.
When raising or lowering the roof, make sure
that no body parts are in the vicinity of moving
components. If someon eb ecomes trapped,
release the button.
Opening and closing This function is only available on vehicles with
KEYLESS-GO or with roof comfort operation. X
Close the trun kl id ( Y
page 72).X
Vehicles with comfort operation: point the
tip of the SmartKey at the driver's door han-
dle. X
Vehicles with KEYLESS-GO: the SmartKey
must be within 6ft(2m )o ft he vehicle.X
To open: press and hold the 6 button on
the SmartKey until the roof is fully opened.
The roof and the rear side windows open. The
fron ts ide windows close.X
To interrupt the opening procedure:
release the 6 button.X
To open the front side windows: press the
6 button on the SmartKey again.X
To close: press and hold the 7 button on
the SmartKey until the roof is fully closed.
The roof and the side windows close. X
To interrupt the closing procedure: release
the 7 button.
Locking the roof again
Important safet yn otes
G WARNING
If you do not fully open/close the soft top, the
soft-top hydraulics depressuriz ea fter as hort
time. This causes the soft top to lower unex-
pectedly and may cause you or other stob e
trapped. There is ar isk of injury. Always open or close the soft top completely.
The roof is not locked if: R
the Y symbol and the Vario-Roof in
Operation message appear in the multifunc-
tion display R
the Y symbol and the Open/Close
Vario-Roof Completely message appear in
the multifunction display and you hear aw arn-
ing tone R
you hear aw arning ton ef or up to ten seconds
when pulling away or while driving
Locking You can lock the roof again if it is not locked
fully. X
Pull over and stop the vehicle safely as soon
as possible, paying attention to road and traf-
fic conditions. X
Ensure that the SmartKey is in position H in
the ignition lock. X
Press the roof switch ( Y
page 78).
Trunk partition
General notes
! To avoid damaging the roof or luggage when
folding back the roof, you should: R
only load the trun ktob elow the trun kp ar-
tition R
not place any objects on or in fron toft he
trun kp artition R
not place any objects on the cover behind
the roll bars R
not allow the cargo to push the trun kp ar-
tition upwards
The trun kp artition can be used to cover luggage
and loads in the trunk. Roof 79
Opening and closing Z

If somebod yb ecomes trapped:R
press one of the memory function position
buttons, or R
press one of the memory function memory
buttons, or R
move the switch for steering wheel adjust-
ment in the opposite direction to that in
which the steering wheel is moving
The adjustment process is stopped.
G WARNING
If you use openings in the bodywork or
detachable parts as steps, you could: R
slip and/or fall R
damage the vehicle and cause yourself to
fall.
There is ar isk of injury.
Alway su se secure climbing aids, e.g. as uita-
ble ladder.
The EASY-ENTRY/EXIT feature makes getting in
and out of you rv ehicle easier.
You can activate and deactivate the EASY-
ENTRY/EXIT feature in the on-board computer
( Y
page 174).
Position of the steering whee lw hen the
EASY-ENTRY/EXIT feature is active The steering wheel swings up when you: R
remove the SmartKey from the ignition lock R
open the driver's door with KEYLESS-GO in
position 1R
open the driver's door and the SmartKey is in
position

Where possible, avoid spinnin gt he drive
wheels when pulling away on slippery roads.
You could otherwise damage the drive train.
Key positions
SmartKey
Z
To remove the SmartKeyG
Power supply for some consumers, such as
the windshield wipersH
Ignition (power supply for all consumers)
and drive positionI
To start the engine
i The SmartKey can be turned in the ignition
lock even if it is not the correct SmartKey for
the vehicle. The ignition is not switched on.
The engine cannot be started.
KEYLESS-GO
General notes Vehicles with KEYLESS-GO are equipped with a
SmartKey featuring an integrated KEYLESS-GO
start function and ad etachable Start/Stop but-
ton.
The Start/Stop button must be inserted in the
ignition lock and the SmartKey must be in the
vehicle.
When you insert the Start/Stop button into the
ignition lock, the system needs approximately
two seconds recognition time. You can then use
the Start/Stop button.
Pressing the Start/Stop button several times in
succession corresponds to the differen tk ey
positions in the ignition lock. This is only the
case if you are not depressing the brake pedal. If you depress the brake pedal and press the
Start/Stop button ,t he engine start si mmedi-
ately.
Ac heck which periodically establishes ar adio
connection between the vehicle and the Smart-
Key determines whether av alid SmartKey is in
the vehicle. This occurs ,f or example, when
starting the engine.
To start the vehicle without actively using the
SmartKey: R
the Start/Stop button must be inserted in the
ignition lock. R
the SmartKey must be in the vehicle. R
the vehicle must not be locked with the
SmartKey or KEYLESS-GO ( Y
page 65).
Do not keep the SmartKey: R
with electronic devices, e.g. am obile phone
or another SmartKey. R
with metallic objects, e.g. coins or metal foil. R
inside metallic objects, e.g. am etal case.
This can impair the functionality of the KEY-
LESS-GO key.
If you lock the vehicle with the SmartKey's
remot ec ontrol or with KEYLESS-GO, after a
short time: R
you will not be able to switch on the ignition
with the Start/Stop button. R
you will not be able to start the engine with the
Start/Stop button until the vehicle is
unlocked again.
The engine can be switched off while the vehicle
is in motion by pressing and holding the Start/
Stop button for three seconds. This function
operates independently of the ECO start/stop
automatic engine switch-off function.
Key positions with KEYLESS-GO
C
Start/Stop button
D
Ignition lock116
Driving
Driving and parking

i You can star tt he engin eint ra nsmission
position ] and \\ .
Starting procedur ew ith th eS martKeyTo star tt he engin eu sing the SmartKey instead
of KEYLESS-GO, pull the Start/Stop button out
of the ignition lock. X
Turn the SmartKey to position I in the igni-
tion lock ( Y
page 116 )a nd release it as soon
as the engin eisr unning.
Using KEYLESS-GO to start th ee ngineThe Start/Stop button can be used to star tt he
vehicle manually without insertin gt he SmartKey
int ot he ignition lock .T he Start/Stop button
must be inserted in the ignition lock and the
SmartKey must be in the vehicle. This mode for
startin gt he engin eo perates independently of
the ECO start/sto pa utomatic engin es tar tf unc-
tion. X
Depress the brak ep edal and keep it
depressed. X
Press the Start/Stop button once
( Y
page 116).
The engin es tarts.
Pulling away
Genera ln otes
G WARNING
If the engin es peed is above the idling speed
and you engage transmission position D or R ,
the vehicle could pull away suddenly. There is
ar isk of an accident.
When engagin gt ra nsmission position D or R ,
always firmly depres st he brak ep edal and do
not simultaneously accelerate.
! Change gear in good tim ea nd avoid spin-
nin gt he wheels. You could otherwise damage
the vehicle.
Depress the accelerator carefully when pulling
away.
The vehicle lock sc entrally onc ey ou have pulled
away. The locking knobs in the doors drop down.
You can open the doors from the inside at any
time. You can also deactivate the automatic locking
feature ( Y
page 173).
It is only possible to shift the transmission from
position ] to the desired position if you
depres st he brak ep edal. Only the nist he shift
lock released.
i Upshifts tak ep lace at higher engin es peeds
afte rac old start. This helps the catalytic con-
verter to reach its operating temperature
more quickly.
Information on the automatic release of the
electric parking brak e( Y
page 133).
Hill start assist Hill star ta ssist helps you when pulling away
forwar dorinr everse on an uphill gradient. It
holds the vehicle for as hor tt im ea fte ry ou have
removed your foot from the brak ep edal. This
gives you enough tim etom ove your foot from
the brak ep edal to the accelerator pedal and to
depres sitb efor et he vehicle begins to roll.
G WARNING
After as hor tt ime, hill star ta ssist will no lon-
ger brak ey our vehicle and it could roll away.
There is ar isk of an accident and injury.
Therefore, quickly move your foot from the
brak ep edal to the accelerator pedal. Never
leave the vehicle when it is held by hill start
assist.
Hill star ta ssist is not active if: R
you are pulling away on al evel road or on a
downhill gradient R
the transmission is in position \\R
the electric parking brak eisa ppliedR
ESP ®
is malfunctioning
ECO start/stop function
Introduction
The ECO start/sto pf unction switches the
engin eo ff automatically if the vehicle is stopped
under certain conditions.
The engin es tarts automatically when the driver
want stop ull away again. The ECO start/stop
function thereby helps you to reduce the fuel
consumption and emissions of your vehicle.118
Driving
Driving and parking