2018 MAZDA MODEL CX-3 tow

m{zd{ c x-3 17
NAVIGATION \fY\fTEM
(IF EQUIPPED)
To plan a route on your navigation system: 1 Push the N AV button on the commander switch.
2 \felect ENTER DESTINATION.
3 \felect Find Address.
NOTE: By default, the navigation system detects the country and city/town you are in.
If needed, you can change the country or state setting by selecting Country or a new
city/town by selecting City or Zip code.
4 Enter the street name.
5 Enter the house number, then select the
.
6
The system transitions to a screen where the input location can be checked.
To transition to the next screen, select
\felect, or to transition to the previous
screen, select
.
NOTE:
• \felect Places Nearby for Points Of Interest (POI) around the selected location,
or select Add to Favorites to register the selected location to Favorites.
• The route can be edited by selecting other options.
7
If
Start is selected or if no operation is performed for 10 seconds, the route guidance
is started. The set route can be checked by selecting MAP.
(\bontinued on next page)
2940109_18b CX-3 SSG_060817.indd 176/8/17 2:38 PM

m{zd{ c x-3 31
Pull to
dispense
windshield
washer fluidMISTAUTO
LO
HI
12
3
WIPER / WA\fHER \bONTROL
CAUTION:
If the ignition is\. ON, turn
the AUTO wipers OFF
when going through a car
wash or while cleaning or touching the windsh\.ield.
WINDSHIELD WIPER / WASHER CONTROL LEVER
(IF EQUIPPED)
The rain sensor senses the amount of rainfall and
turns the wipers on or off.
Rotating the inner ri\.ng
clockwise (away from you)
creates greater wiper sensitivity and makes the
wipers move faster. The + position increases wiper
speed. Rotating the inner ring counterclockwise
(toward you) makes the wipers move
slower. The - position
decreases wiper speed.
Normal speed
Intermittent
REAR WINDOW
WIPER/WASHER
(hold as desired)
NOTE: Vehicles not equipped with AUTO wipers will have
INT wipers. \fet the lever to INT and choose an interval timing by rotating the ring between fast and slow.
Windshield
wiper/washer
control lever
2940109_18b CX-3 SSG_060817.indd 316/8/17 2:40 PM

m{zd{ c x-3 33
HIGH BEAM CONTROL (HBC)
With HBC, the headlights are switched to high beams at speeds above 18 mph when there are no vehicles in front of your vehicle or approaching in the oppo\Xsite direction.
The HBC system switches to low beam when: •
You are approaching a vehicle or a vehicle is approaching in the oppo\.site direction.
• Driving on roads lined with street lights or well-lit cities and towns.
• At speeds lower than 12 mph.
To turn HBC on: 1 Turn the headlight switch to the AUTO position.
2 Push the headlight lever forward to the High Beam position.
NOTE: When the HB\b system is on, the HB\b indicator light in the instrument cluster will
illuminate (green). The High Beam indicator light will turn on (blue) when the HB\b system
switches to high beam and will turn off when the HB\b system switches to low beam.
Push for
high beams
Turn to the
AUTO position
HIGH BEAM \bONTROL
(IF EQUIPPED)
2940109_18b CX-3 SSG_060817.indd 336/8/17 2:40 PM

m{zd{ c x-3 35
AUDIO \bONTROL\f
(IF EQUIPPED)
AUDIO OPERATION USING VOICE
Audio operation and media selection can be done using v\.oice recognition. Push the
TALK
button on the steering wheel, wait for a beep, then say a command in a clear,
natural voice (not too fast or too slow). \fome common commands are listed below.
Play (and any of the following):
AM, FM, XM, Bluetooth
®, Aha, Pandora, \ftitcher, U\fB, AUX
Play or Resume/Pause or Stop/Next or Previous Play (and any of the following when
connected to USB port): \fong, Playlist , Artist ,
Album \., Genre , Folder
Tune to Station:
Tune to Channel Number (XM)
NOTE: Push the TALK button and say “Help” at any time to hear a list of
available commands.
BLUETOOTH® (BT) AUDIO
Bluetooth®-enabled phones and audio players provide an opportunity to play music
through the audio system without wires.
\fome phone models d\.o not support all features.
Go to www.mazdausa.com/mazdaconnect or contact (800) 430\f0153 for further
assistance or to report a phone/audio device concern.
NOTE: To use BT audio, make sure the musical icon is displayed by going to
Bluetooth® in Device \fettings. \fome Bluetooth® audio devices need a certain amount of
time before the icon is displayed.
PLAYING BLUETOOTH® AUDIO
1 Make sure the BT audio device is paired to your vehicle.
2
Turn on the BT audio device and open the aud\.io app on the device.
3
\felect Bluetooth
® from \fources. \fee your Owner’s Manual for further information on
Pandora, Aha, and \ftitcher operations.
NOTE: In order to use Aha, Pandora and \ftitcher as audio sources, the app must be
installed on your phone. These apps stream music using your data plan and listening to
them counts toward your monthly cellular data usage.
2940109_18b CX-3 SSG_060817.indd 356/8/17 2:40 PM