2018 Lexus LC500 clock setting

89
2
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
Vehicle status information and indicators
Outside temperature
Displays the outside temperature within the range of -40°C (-40°F) to 50°C (122°F)
Low outside temperature indicator comes on when the ambient temperature is 3°C (37°F)
or lower
Tachometer
Displays the engine speed in revolutions per minute
Speedometer
Shift position/shift range/gear position ( P.173, 179)
Shift position indicator ( P.175, 181)
Clock
Time displayed is linked to the analog clock on the instrument panel. (P.297)
Engine coolant temperature gauge
Displays the engine coolant temperature
If the engine coolant temperature gauge indi cator enters the red zone, a buzzer sounds
and the high coolant temperature warning light comes on
Odometer and trip meter display
Odometer:
Displays the total distance the vehicle has been driven
Trip meter:
Displays the distance the vehicle has been driven since the meter was last reset
Trip meters “A” and “B” can be used to record and display different distances independently
Fuel gauge
Displays the quantity of fuel remaining in the tank
Multi-information display
Presents the driver with a variety of vehicle data (P.92)
Displays warning messages in case of a malfunction (P.378)
Motor power display/Hybrid System Indicator (LC500h)
Displays the motor power display (P.87) or Hybrid System Indicator (P.86)
■Speed warning
When the vehicle reaches the set
speed, the speed warning display will
flash.
This setting can be enabled on the
multi-information display. ( P.92)
Always observe the legal speed limit when
driving on public roads.
■Rev indicator
When the engine reaches a set speed
or the red zone, a ring-shaped indica-
tor will be displayed on the tachometer.
B
C
D
E
F
G
H
I
J
K
L

97
2
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
Vehicle status information and indicators
■Eco Driving Indicator Light
(LC500)
Select to activate/deactivate the Eco
Driving Indicator Light.
■EV indicator (LC500h)
Select to activate/deactivate the EV
indicator.
■Drive information 1/Drive infor-
mation 2
Select up to 2 items that will be dis-
played on the “Drive Info 1” screen and
“Drive Info 2” screen respectively.
( P.94)
■Pop-up display
Select to set the following pop-up dis-
plays, which may appear in some situa-
tions, on/off.
• Route guidance display of the navi-
gation system-linked system (if
equipped)
• Making call display of the hands-
free phone system
• Audio system operation display
• Instrument panel brightness adjust-
ment display
■Ring position memory
Select to change the meter ring posi-
tion when the engine is
started.
The position before the engine system> is stopped or the center posi-
tion can be selected.
■Accent color
Select to change the accent color on
the screen, such as the cursor color.
■Rev indicator
Select to set the rev indicator on/off.
When set to on, proceed to select the
engine speed at which the rev indicator
will be displayed.
■Rev peak
Select to set the rev peak on/off.
■Clock
Select to switch between 24-hour dis-
play and 12-hour display.
■Initialization
Select to reset the meter display set-
tings.
■Suspension of the settings display
In the following situations, operation of the
settings display will be temporarily sus- pended.
●When a warning message appears on the multi-information display
●When the vehicle begins to move
■Customization
The settings can be changed on of the
multi-information display.
●Settings of the driving assist systems ( P.423)
●Vehicle settings (P.100, 335, 337, 423)

321
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
LC500
LC500h
1 Remove the oil filler cap by turning
it counterclockwise.
2 Add engine oil slowly, checking the
dipstick.
3 Install the oil filler cap by turning it
clockwise.
■Engine oil consumption
A certain amount of engine oil will be con-
sumed while driving. In the following situa- tions, oil consumption may increase, and engine oil may need to be refilled in
between oil maintenance intervals.
●When the engine is new, for example
directly after purchasing the vehicle or after replacing the engine
●If low quality oil or oil of an inappropriate viscosity is used
●When driving at high engine speeds or with a heavy load, or when driving while accelerating or decelerating frequently
●When leaving the engine idling for a long time, or when driving frequently through heavy traffic
■After changing the engine oil (LC500h)
The engine oil maintenance data should be reset. Perform the following procedures:
1 While the vehicle is stopped, press
of the meter control switches.
2 Press or of the meter control
switches, and select .
3 Press or of the meter control
switches, select “Vehicle Settings”, and
then press “OK”.
4 Press or of the meter control
switches, select “Oil Maintenance”, and
then press “OK”.
5 Select “Yes” and then press “OK”.
A message will be displayed on the multi- information display.
WARNING
■Used engine oil
●Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflamma-
tion and skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used
engine oil from your skin, wash thor- oughly with soap and water.

425
8
-$@-$I@0.@0.&@ &&

8-2. Customization
Vehicle specifications
*1: For details about each function: P.88, 96
*2: The default setting varies according to country.
*3:LC500
*4:LC500h
*5: 2 of the following items: current fuel consumption, average fuel economy (after reset),
average fuel economy (after start), average fuel economy (after refuel), average vehicle
speed (after reset), average vehicle speed (after start), elapsed time (after reset),
elapsed time (after start), distance (driving range), distance (after start), blank.
*6: Refer to the “NAVIGATION SYSTEM OWNER’S MANUAL”.
Accent colorColor 1Color 2O*6O—
Rev indicatorOffOn—O—
Rev indicator red zone setting5000 r/min.*3
4000 r/min.*4
2000 - 7300
r/min.*3
2000 - 6600
r/min.*4
—O—
Rev peakOffOn—O—
Clock24-hour dis-
play12-hour display—O—
Sensor sensitivity for darkening the
brightness of the instrument cluster
depending on the outside bright-
ness
Standard-2 to 2——O
Sensor sensitivity for returning the
brightness of the instrument cluster
to the original level depending on
the outside brightness
Standard-2 to 2——O
Suggestion functionOn
On
(when the vehicle is
stopped)O—O
Off
Function*1Default settingCustomized settingABC